Daikin 2MKS70JVLT User manual

REMOVAL
PROCEDURE
SERVICE MANUAL
Outdoor Unit
Inverter
Multi Type
7.0/8.0/9.0/10.0 kW Class
24000/32000 Btu/h Class
Si121176

Service Manual
Removal Procedure
Outdoor Unit
Applicable Models
zCooling Only zHeat Pump
2MKS70JVLT 3MXS24JVJU
2MKS80JVLT 4MXS32GVJU
3MKS90KVLT
4MKS100KVLT 2MXS70JVLT
2MXS80JVLT
4MKS90EVMA 3MXS90KVLT
4MXS100KVLT
4MKS80KVM
4MKS100KVM 4MXS80EVMA
5MKS90E2V3B 4MXS80KVM
4MXS100KVM
4MXS80E2V3B
5MXS90E2V3B

Si121176
Removal Procedure 1
Table of Contents
1. Removal of Outer Panels ........................................................................2
2. Removal of Electrical Box .....................................................................16
3. Removal of PCBs..................................................................................22
4. Removal of Fan Motor...........................................................................26
5. Removal of Coils / Thermistors .............................................................27
6. Removal of Sound Blankets..................................................................32
7. Removal of Compressor .......................................................................35
Note: The illustrations may be slightly different depending on the model.
The illustrations are for heat pump models as representative.

Removal of Outer Panels Si121176
2Removal Procedure
1. Removal of Outer Panels
Procedure Warning Be sure to wait for 10 minutes or more after turning off all power
supplies before disassembling work.
Step Procedure Points
Appearance features
1. Remove the suction grille. The hooks are secured in
the clearances of the
outdoor heat exchanger fins.
1Unfasten the 2 hooks at
the bottom first.
(
R6368
)
Hook
Rear side
(R14612)
Suction grille
(R6370)

Si121176 Removal of Outer Panels
Removal Procedure 3
2Slide the suction grille
downward to unfasten
the 3 top hooks.
3Remove the suction
grille.
2. Remove the top panel.
1Remove the 4 screws
on the back and the
screw on the left side
panel.
Step Procedure Points
Hook
(
R14613
)
(R6372)
Top panel
Left side panel
(R6373)

Removal of Outer Panels Si121176
4Removal Procedure
2Remove the 2 screws
on the front and the
screw on the right side
panel.
3Lift the top panel and
remove it.
3. Remove the right side
panel.
1Remove the 5 screws.
Step Procedure Points
(R6374)
Right side
panel
(R6375)
(R6376)
Right side panel

Si121176 Removal of Outer Panels
Removal Procedure 5
2Slide the right side
panel downward to
unfasten the 2 hooks on
the back side.
Step Procedure Points
(R6377)
Hook
(R14614)
Hook
(R14615)

Removal of Outer Panels Si121176
6Removal Procedure
3Remove the right side
panel.
The US model has a service
lid on the stop valve
mounting plate.
Remove the 2 screws to
remove the service lid.
The US model has a conduit
mounting plate.
4. Remove the front panel
(2). This screw is M5 × 16
1Remove the 2 screws.
2Slide the front panel (2)
downward to unfasten
the hook.
Step Procedure Points
(R10441)
Service lid
Screw (R10372)
Lock nut
Conduit
Knockout hole
(R17351)
Conduit
mounting plate
(R10629)
+
+
Front Panel (2)
Front
Panel (1)
(R10374)

Si121176 Removal of Outer Panels
Removal Procedure 7
3Remove the front panel
(2).
5. Remove the front panel
(1).
Remove the discharge grille
and outdoor fan first to
remove the front panel (1).
1Remove the 4 screws
on the discharge grille.
2Pull the bottom of the
discharge grille.
Step Procedure Points
(R6383)
(R10375)
(R10376)
Front
Panel (1)
Discharge grille
(R10377)

Removal of Outer Panels Si121176
8Removal Procedure
3Slide the discharge
grille downward to
unfasten the 2 hooks at
the top.
4Remove the discharge
grille.
5Remove the nut and
remove the outdoor fan.
Nut size : M8
When reassembling, align
the mark of the outdoor
fan with the D-cut section of
the motor shaft.
Step Procedure Points
(R17173)
Hook
(R10380)
(R10381)
Outdoor fan
13 mm
(R12301)