Daikin RXMQ4 5 6PVE User manual

Si34 - 603
Service Manual / R-410A RX(Y)MQ4·5·6PVE Si34-603
RX(Y)MQ4·5·6PVE
R-410A
Heat Pump 50/60Hz
Cooling Only 50/60Hz
Printed in Japan 07/2006 AK
July

Si34-603
Table of Contents i
R-410A
Heat Pump / Cooling Only
50/60Hz
1. Introduction .............................................................................................v
1.1 Safety Cautions ........................................................................................ v
1.2 PREFACE ............................................................................................... ix
Part 1 General Information ........................................................... 1
1. Model Names of Indoor/Outdoor Units....................................................2
2. External Appearance...............................................................................3
2.1 Indoor Units ..............................................................................................3
3. Capacity Range.......................................................................................4
Part 2 Specifications .................................................................... 5
1. Specifications ..........................................................................................6
1.1 Outdoor Units ...........................................................................................6
1.2 Indoor Units ............................................................................................10
Part 3 List of Electrical and Functional Parts............................ 35
1. List of Electrical and Functional Parts ...................................................36
1.1 Outdoor Unit ...........................................................................................36
1.2 Indoor Unit..............................................................................................37
Part 4 Refrigerant Circuit ........................................................... 43
1. Refrigerant Circuit .................................................................................44
1.1 RX(Y)MQ4 / 5 / 6P .................................................................................44
2. Functional Parts Layout ........................................................................46
2.1 RX(Y)MQ4 / 5 / 6P .................................................................................46
Part 5 Function............................................................................ 47
1. Operation Mode ....................................................................................48
2. Basic Control.........................................................................................49
2.1 Normal Operation ...................................................................................49
2.2 Compressor PI Control...........................................................................50
2.3 Electronic Expansion Valve PI Control...................................................51
2.4 Cooling Operation Fan Control...............................................................52
3. Special Control......................................................................................53
3.1 Startup Control .......................................................................................53
3.2 Oil Return Operation ..............................................................................54
3.3 Defrosting Operation ..............................................................................56
3.4 Pump-down Residual Operation ............................................................57
3.5 Restart Standby......................................................................................58
3.6 Stopping Operation ................................................................................59

Si34-603
ii Table of Contents
4. Protection Control .................................................................................60
4.1 High Pressure Protection Control...........................................................60
4.2 Low Pressure Protection Control............................................................61
4.3 Discharge Pipe Protection Control .........................................................62
4.4 Inverter Protection Control .....................................................................63
5. Other Control.........................................................................................64
5.1 Demand Operation .................................................................................64
5.2 Heating Operation Prohibition ................................................................64
6. Outline of Control (Indoor Unit) .............................................................65
6.1 Drain Pump Control................................................................................65
6.2 Louver Control for Preventing Ceiling Dirt..............................................67
6.3 Thermostat Sensor in Remote Controller...............................................68
6.4 Freeze Prevention ..................................................................................70
6.5 View of Operations of Swing Flaps ........................................................71
6.6 Electronic Expansion Valve Control .......................................................72
6.7 Hot Start Control (In Heating Operation Only)........................................72
Part 6 Test Operation ................................................................. 73
1. Test Operation ......................................................................................74
1.1 Procedure and Outline ...........................................................................74
1.2 Operation when Power is Turned On .....................................................77
2. Outdoor Unit PC Board Layout .............................................................78
3. Field Setting ..........................................................................................79
3.1 Field Setting from Remote Controller .....................................................79
3.2 Field Setting from Outdoor Unit..............................................................92
Part 7 Troubleshooting ............................................................. 111
1. Symptom-based Troubleshooting .......................................................113
2. Troubleshooting by Remote Controller ...............................................116
2.1 The INSPECTION / TEST Button.........................................................116
2.2 Self-diagnosis by Wired Remote Controller .........................................117
2.3 Self-diagnosis by Wireless Remote Controller .....................................118
2.4 Operation of the Remote Controller’s Inspection /
Test Operation Button ..........................................................................120
2.5 Remote Controller Service Mode .........................................................121
2.6 Remote Controller Self-Diagnosis Function .........................................123
3. Troubleshooting by Indication on the Remote Controller ....................130
3.1 “A0” Indoor Unit: Error of External Protection Device ...........................130
3.2 “A1” Indoor Unit: PC Board Defect.........................................................131
3.3 “A3” Indoor Unit: Malfunction of Drain Level Control System (33H)......132
3.4 “A6” Indoor Unit: Fan Motor (M1F) Lock, Overload...............................134
3.5 “A7” Indoor Unit: Malfunction of Swing Flap Motor (MA) .......................135
3.6 “A9” Indoor Unit: Malfunction of Moving Part of
Electronic Expansion Valve (20E) ........................................................137
3.7 “AF” Indoor Unit: Drain Level above Limit..............................................139
3.8 “AJ” Indoor Unit: Malfunction of Capacity Determination Device ..........140
3.9 “C4” Indoor Unit: Malfunction of Thermistor (R2T)
for Heat Exchanger ..............................................................................141
3.10 “C5” Indoor Unit: Malfunction of Thermistor (R3T) for Gas Pipes..........142
3.11 “C9” Indoor Unit: Malfunction of Thermistor (R1T) for Suction Air.........143

Si34-603
Table of Contents iii
3.12 “CA” Indoor Unit: Malfunction of Thermistor for Discharge Air...............144
3.13 “CJ” Indoor Unit: Malfunction of Thermostat Sensor
in Remote Controller ............................................................................145
3.14 “E1” Outdoor Unit: PC Board Defect ......................................................146
3.15 “E3” Outdoor Unit: Actuation of High Pressure Switch ..........................147
3.16 “E4” Outdoor Unit: Actuation of Low Pressure Sensor ..........................149
3.17 “E5”Compressor Motor Lock ................................................................151
3.18 “E7”Malfunction of Outdoor Unit Fan Motor..........................................152
3.19 “E9” Outdoor Unit: Malfunction of Moving Part of
Electronic Expansion Valve (Y1E, Y3E)...............................................153
3.20 “F3” Outdoor Unit: Abnormal Discharge Pipe Temperature ..................155
3.21 “F6”Outdoor Unit: Refrigerant Overcharged.........................................156
3.22 “H9” Outdoor Unit: Malfunction of Thermistor (R1T) for Outdoor Air.....157
3.23 “J3” Outdoor Unit: Malfunction of Discharge Pipe Thermistor (R2T) ....158
3.24 “J5” Outdoor Unit: Malfunction of Thermistor (R3T, R5T) for
Suction Pipe 1, 2 ..................................................................................159
3.25 “J6” Outdoor Unit: Malfunction of Thermistor (R4T) for
Outdoor Unit Heat Exchanger ..............................................................160
3.26 “J7” Outdoor Unit: Malfunction of Thermistor (R7T) for
Outdoor Unit Liquid Pipe ......................................................................161
3.27 “J9” Outdoor Unit: Malfunction of Subcooling Heat Exchanger
Gas Pipe Thermistor (R6T) ..................................................................162
3.28 “JA” Outdoor Unit: Malfunction of High Pressure Sensor......................163
3.29 “JC” Outdoor Unit: Malfunction of Low Pressure Sensor.......................164
3.30 “L1” Outdoor Unit: Malfunction of PC Board ..........................................165
3.31 “L4” Outdoor Unit: Malfunction of Inverter Radiating Fin
Temperature Rise.................................................................................166
3.32 “L5” Outdoor Unit: Inverter Compressor Abnormal ...............................167
3.33 “L8” Outdoor Unit: Inverter Current Abnormal .......................................168
3.34 “L9” Outdoor Unit: Inverter Start up Error..............................................169
3.35 “LC” Outdoor Unit: Malfunction of Transmission between Inverter
and Control PC Board ..........................................................................170
3.36 “P1” Outdoor Unit: High Voltage of Capacitor in Main Inverter Circuit ...171
3.37 “P4” Outdoor Unit: Malfunction of Inverter Radiating Fin
Temperature Rise Sensor ....................................................................172
3.38 “UO” Outdoor Unit: Low Pressure Drop Due to Refrigerant Shortage
or Electronic Expansion Valve Failure..................................................173
3.39 “U2” Power Supply Insufficient or Instantaneous Failure ......................175
3.40 “U3”Check Operation not Executed......................................................177
3.41 “U4”Malfunction of Transmission between Indoor Units and
Outdoor Units .......................................................................................178
3.42 “U5”Malfunction of Transmission between Remote Controller
and Indoor Unit.....................................................................................180
3.43 “U8”Malfunction of Transmission between Main and
Sub Remote Controllers .......................................................................181
3.44 “U9” Malfunction of Transmission between Indoor and
Outdoor Units in the Same System ......................................................182
3.45 “UA” Excessive Number of Indoor Units ................................................184
3.46 “UC” Address Duplication of Central Remote Controller........................185
3.47 “UE”Malfunction of Transmission between Central Remote Controller
and Indoor Unit.....................................................................................186
3.48 “UF” System is not Set yet .....................................................................188
3.49 “UH” Malfunction of System, Refrigerant System Address Undefined...189

Si34-603
iv Table of Contents
4. Troubleshooting by Indication on the Centralized
Remote Controller ...............................................................................190
4.1 “UE”Malfunction of Transmission between Centralized Remote
Controller and Indoor Unit ....................................................................190
4.2 “M1”PC Board Defect ............................................................................191
4.3 “M8” Malfunction of Transmission between Optional Controllers for
Centralized Control...............................................................................192
4.4 “MA” Improper Combination of Optional Controllers for
Centralized Control...............................................................................193
4.5 “MC” Address Duplication, Improper Setting ..........................................195
5. Troubleshooting by Indication on the Unified ON/OFF Controller.......196
5.1 Operation Lamp Blinks .........................................................................196
5.2 Display “Under Host Computer Integrate Control” Blinks
(Repeats Single Blink)..........................................................................198
5.3 Display “Under Host Computer Integrate Control” Blinks
(Repeats Double Blink) ........................................................................201
Part 8 Appendix......................................................................... 205
1. Piping Diagrams..................................................................................206
1.1 Outdoor Unit .........................................................................................206
1.2 Indoor Unit............................................................................................207
2. Wiring Diagrams..................................................................................210
2.1 Outdoor Unit .........................................................................................210
2.2 Field Wiring ..........................................................................................212
2.3 Indoor Unit............................................................................................213
3. Option List ...........................................................................................226
3.1 Option List of Controllers......................................................................226
3.2 Option List of Outdoor Unit...................................................................228
4. Example of Connection .......................................................................229
5. Thermistor Resistance / Temperature Characteristics........................231
6. Pressure Sensor .................................................................................233
7. Method of Replacing the Inverter’s Power Transistors Modules.........234
Part 9 Precautions for New Refrigerant (R-410A) ....................237
1. Precautions for New Refrigerant (R-410A) .........................................238
1.1 Outline ..................................................................................................238
1.2 Refrigerant Cylinders............................................................................240
1.3 Service Tools........................................................................................241
Index ............................................................................................. i
Drawings & Flow Charts ...............................................................iii

Si34-603 Introduction
v
1. Introduction
1.1 Safety Cautions
Cautions and
Warnings
Be sure to read the following safety cautions before conducting repair work.
The caution items are classified into “ Warning” and “ Caution”. The “ Warning”
items are especially important since they can lead to death or serious injury if they are not
followed closely. The “ Caution” items can also lead to serious accidents under some
conditions if they are not followed. Therefore, be sure to observe all the safety caution items
described below.
About the pictograms
This symbol indicates an item for which caution must be exercised.
The pictogram shows the item to which attention must be paid.
This symbol indicates a prohibited action.
The prohibited item or action is shown inside or near the symbol.
This symbol indicates an action that must be taken, or an instruction.
The instruction is shown inside or near the symbol.
After the repair work is complete, be sure to conduct a test operation to ensure that the
equipment operates normally, and explain the cautions for operating the product to the
customer
1.1.1 Caution in Repair
Warning
Be sure to disconnect the power cable plug from the plug socket before
disassembling the equipment for a repair.
Working on the equipment that is connected to a power supply can cause an
electrical shook.
If it is necessary to supply power to the equipment to conduct the repair or
inspecting the circuits, do not touch any electrically charged sections of the
equipment.
If the refrigerant gas discharges during the repair work, do not touch the
discharging refrigerant gas.
The refrigerant gas can cause frostbite.
When disconnecting the suction or discharge pipe of the compressor at the
welded section, release the refrigerant gas completely at a well-ventilated
place first.
If there is a gas remaining inside the compressor, the refrigerant gas or
refrigerating machine oil discharges when the pipe is disconnected, and it can
cause injury.
If the refrigerant gas leaks during the repair work, ventilate the area. The
refrigerant gas can generate toxic gases when it contacts flames.
The step-up capacitor supplies high-voltage electricity to the electrical
components of the outdoor unit.
Be sure to discharge the capacitor completely before conducting repair work.
A charged capacitor can cause an electrical shock.
Do not start or stop the air conditioner operation by plugging or unplugging the
power cable plug.
Plugging or unplugging the power cable plug to operate the equipment can
cause an electrical shock or fire.

Introduction Si34-603
vi
1.1.2 Cautions Regarding Products after Repair
Caution
Do not repair the electrical components with wet hands.
Working on the equipment with wet hands can cause an electrical shock.
Do not clean the air conditioner by splashing water.
Washing the unit with water can cause an electrical shock.
Be sure to provide the grounding when repairing the equipment in a humid or
wet place, to avoid electrical shocks.
Be sure to turn off the power switch and unplug the power cable when cleaning
the equipment.
The internal fan rotates at a high speed, and cause injury.
Do not tilt the unit when removing it.
The water inside the unit can spill and wet the furniture and floor.
Be sure to check that the refrigerating cycle section has cooled down
sufficiently before conducting repair work.
Working on the unit when the refrigerating cycle section is hot can cause burns.
Use the welder in a well-ventilated place.
Using the welder in an enclosed room can cause oxygen deficiency.
Warning
Be sure to use parts listed in the service parts list of the applicable model and
appropriate tools to conduct repair work. Never attempt to modify the
equipment.
The use of inappropriate parts or tools can cause an electrical shock,
excessive heat generation or fire.
When relocating the equipment, make sure that the new installation site has
sufficient strength to withstand the weight of the equipment.
If the installation site does not have sufficient strength and if the installation
work is not conducted securely, the equipment can fall and cause injury.
Be sure to install the product correctly by using the provided standard
installation frame.
Incorrect use of the installation frame and improper installation can cause the
equipment to fall, resulting in injury.
For integral units
only
Be sure to install the product securely in the installation frame mounted on a
window frame.
If the unit is not securely mounted, it can fall and cause injury.
For integral units
only
Be sure to use an exclusive power circuit for the equipment, and follow the
technical standards related to the electrical equipment, the internal wiring
regulations and the instruction manual for installation when conducting
electrical work.
Insufficient power circuit capacity and improper electrical work can cause an
electrical shock or fire.

Si34-603 Introduction
vii
1.1.3 Inspection after Repair
Be sure to use the specified cable to connect between the indoor and outdoor
units. Make the connections securely and route the cable properly so that there
is no force pulling the cable at the connection terminals.
Improper connections can cause excessive heat generation or fire.
When connecting the cable between the indoor and outdoor units, make sure
that the terminal cover does not lift off or dismount because of the cable.
If the cover is not mounted properly, the terminal connection section can cause
an electrical shock, excessive heat generation or fire.
Do not damage or modify the power cable.
Damaged or modified power cable can cause an electrical shock or fire.
Placing heavy items on the power cable, and heating or pulling the power cable
can damage the cable.
Do not mix air or gas other than the specified refrigerant (R-410A) in the
refrigerant system.
If air enters the refrigerating system, an excessively high pressure results,
causing equipment damage and injury.
If the refrigerant gas leaks, be sure to locate the leak and repair it before
charging the refrigerant. After charging refrigerant, make sure that there is no
refrigerant leak.
If the leak cannot be located and the repair work must be stopped, be sure to
perform pump-down and close the service valve, to prevent the refrigerant gas
from leaking into the room. The refrigerant gas itself is harmless, but it can
generate toxic gases when it contacts flames, such as fan and other heaters,
stoves and ranges.
When replacing the coin battery in the remote controller, be sure to disposed
of the old battery to prevent children from swallowing it.
If a child swallows the coin battery, see a doctor immediately.
Warning
Caution
Installation of a leakage breaker is necessary in some cases depending on the
conditions of the installation site, to prevent electrical shocks.
Do not install the equipment in a place where there is a possibility of
combustible gas leaks.
If a combustible gas leaks and remains around the unit, it can cause a fire.
Be sure to install the packing and seal on the installation frame properly.
If the packing and seal are not installed properly, water can enter the room and
wet the furniture and floor.
For integral units
only
Warning
Check to make sure that the power cable plug is not dirty or loose, then insert
the plug into a power outlet all the way.
If the plug has dust or loose connection, it can cause an electrical shock or fire.
If the power cable and lead wires have scratches or deteriorated, be sure to
replace them.
Damaged cable and wires can cause an electrical shock, excessive heat
generation or fire.
Do not use a joined power cable or extension cable, or share the same power
outlet with other electrical appliances, since it can cause an electrical shock,
excessive heat generation or fire.

Introduction Si34-603
viii
1.1.4 Using Icons
Icons are used to attract the attention of the reader to specific information. The meaning of each
icon is described in the table below:
1.1.5 Using Icons List
Caution
Check to see if the parts and wires are mounted and connected properly, and
if the connections at the soldered or crimped terminals are secure.
Improper installation and connections can cause excessive heat generation,
fire or an electrical shock.
If the installation platform or frame has corroded, replace it.
Corroded installation platform or frame can cause the unit to fall, resulting in
injury.
Check the grounding, and repair it if the equipment is not properly grounded.
Improper grounding can cause an electrical shock.
Be sure to measure the insulation resistance after the repair, and make sure
that the resistance is 1 Mohm or higher.
Faulty insulation can cause an electrical shock.
Be sure to check the drainage of the indoor unit after the repair.
Faulty drainage can cause the water to enter the room and wet the furniture
and floor.
Icon Type of
Information
Description
Note:
Note A “note” provides information that is not indispensable, but may
nevertheless be valuable to the reader, such as tips and tricks.
Caution
Caution A “caution” is used when there is danger that the reader, through
incorrect manipulation, may damage equipment, loose data, get
an unexpected result or has to restart (part of) a procedure.
Warning
Warning A “warning” is used when there is danger of personal injury.
Reference A “reference” guides the reader to other places in this binder or
in this manual, where he/she will find additional information on a
specific topic.

Si34-603 Introduction
ix
1.2 PREFACE
Thank you for your continued patronage of Daikin products.
This is the new service manual for Daikin's Year 2006 VRVIII-S series Heat Pump / Cooling
Only System.
Daikin offers a wide range of models to respond to building and office air conditioning needs.
We are confident that customers will be able to find the models that best suit their needs.
This service manual contains information regarding the servicing of VRVIII-S series R-410A
Heat Pump / Cooling Only System.
July, 2006
After Sales Service Division

Introduction Si34-603
x

Si34-603
General Information 1
Part 1
General Information
1. Model Names of Indoor/Outdoor Units....................................................2
2. External Appearance...............................................................................3
2.1 Indoor Units ..............................................................................................3
3. Capacity Range.......................................................................................4

Model Names of Indoor/Outdoor Units Si34-603
2General Information
1. Model Names of Indoor/Outdoor Units
*Indoor Units
Note:FXDQ has following 2 Series, as shown below.
FXDQ-P, N(A)VET: without Drain Pump (For General, Asia: except for EU, China and Australia)
FXDQ-P, N(A)VE: with Drain Pump
BEV unit is required for each indoor unit.
*1 VE:1φ, 220~240V, 50Hz, 1φ, 220V, 60Hz
V1:1φ, 220~240V, 50Hz
Outdoor Units
Type Model Name Power Supply
Ceiling Mounted
Cassette Type
(Double Flow) FXCQ 20M 25M 32M 40M 50M 63M 80M — 125M
VE *1
Ceiling Mounted
Cassette Type
(Multi Flow) FXFQ — 25M 32M 40M 50M 63M 80M 100M 125M
Ceiling Mounted
Cassette Corner
Type FXKQ —
25MA 32MA 40MA — 63MA ———
Slim Ceiling
Mounted Duct
Type
FXDQ-
PVE 20P 25P 32P — — — — — —
FXDQ-
PVET 20P 25P 32P — — — — — —
FXDQ-
NAVE 20NA 25NA 32NA 40NA 50NA 63NA — — —
FXDQ-
NVET 20N 25N 32N 40N 50N 63N — — —
Ceiling Mounted
Built-In Type FXSQ 20M 25M 32M 40M 50M 63M 80M 100M 125M
Ceiling Mounted
Duct Type FXMQ — — —
40MA 50MA 63MA 80MA 100MA 125MA
Ceiling Suspended
Type FXHQ — —
32MA —— 63MA — 100MA —
Wall Mounted
Type FXAQ
20MA 25MA 32MA 40MA 50MA 63MA ———
Floor Standing
Type FXLQ
20MA 25MA 32MA 40MA 50MA 63MA ———
Concealed Floor
Standing Type FXNQ
20MA 25MA 32MA 40MA 50MA 63MA ———
Ceiling Suspended
Cassette Type FXUQ——————
71MA 100MA 125MA V1
Connection Unit BEVQ-
M(A) ——————
71MA 100MA 125MA VE *1
Series Model Name Power Supply
Inverter
Heat Pump RXYMQ 4P 5P 6P VE *2
Cooling Only RXMQ 4P 5P 6P VE *2
*2 VE:1φ, 220~230V, 50Hz, 1φ, 220V, 60Hz

Si34-603 External Appearance
General Information 3
2. External Appearance
2.1 Indoor Units
Ceiling Mounted Cassette Type (Double Flow)
FXCQ20M
FXCQ25M
FXCQ32M
FXCQ40M
FXCQ50M
FXCQ63M
FXCQ80M
FXCQ125M
Ceiling Suspended Type
FXHQ32MA
FXHQ63MA
FXHQ100MA
Ceiling Mounted Cassette Type (Multi Flow)
FXFQ25M
FXFQ32M
FXFQ40M
FXFQ50M
FXFQ63M
FXFQ80M
FXFQ100M
FXFQ125M
Wall Mounted Type
FXAQ20MA
FXAQ25MA
FXAQ32MA
FXAQ40MA
FXAQ50MA
FXAQ63MA
Ceiling Mounted Cassette Corner Type
FXKQ25MA
FXKQ32MA
FXKQ40MA
FXKQ63MA
Floor Standing Type
FXLQ20MA
FXLQ25MA
FXLQ32MA
FXLQ40MA
FXLQ50MA
FXLQ63MA
Slim Ceiling Mounted Duct Type
FXDQ20P FXDQ20N(A)
FXDQ25P FXDQ25N(A)
FXDQ32P FXDQ32N(A)
FXDQ40N(A)
FXDQ50N(A)
FXDQ63N(A)
with Drain Pump (VE)
without Drain Pump (VET)
Concealed Floor Standing Type
FXNQ20MA
FXNQ25MA
FXNQ32MA
FXNQ40MA
FXNQ50MA
FXNQ63MA
Ceiling Mounted Built-In Type
FXSQ20M
FXSQ25M
FXSQ32M
FXSQ40M
FXSQ50M
FXSQ63M
FXSQ80M
FXSQ100M
FXSQ125M
Ceiling Suspended Cassette Type
(Connection Unit Series)
FXUQ71MA +
FXUQ100MA +
FXUQ125MA +
Connection Unit
Ceiling Mounted Duct Type
FXMQ40MA
FXMQ50MA
FXMQ63MA
FXMQ80MA
FXMQ100MA
FXMQ125MA
BEVQ71MA
BEVQ100MA
BEVQ125MA

Capacity Range Si34-603
4General Information
3. Capacity Range
Outdoor Units
Indoor Units
Note:FXDQ has following 2 Series, as shown below.
FXDQ-P, NVET: without Drain Pump (For General, Asia: except for EU, China and Australia)
FXDQ-P, NAVE: with Drain Pump
Capacity Range 4HP 5HP 6HP
RX(Y)MQ 4P 5P 6P
No of Indoor
Units to be
Connected
689
Total Capacity
Index of Indoor
Units to be
Connected
50~130 62.5~162.5 70~182
Capacity Range 0.8HP 1HP 1.25HP 1.6HP 2HP 2.5HP 3.2HP 4HP 5HP
Capacity Index 20 25 31.25 40 50 62.5 80 100 125
Ceiling Mounted
Cassette Type
(Double Flow)
FXCQ 20M 25M 32M 40M 50M 63M 80M — 125M
Ceiling Mounted
Cassette Type
(Multi Flow)
FXFQ — 25M 32M 40M 50M 63M 80M 100M 125M
Ceiling Mounted
Cassette Corner Type FXKQ — 25MA 32MA 40MA — 63MA — — —
Slim Ceiling Mounted
Duct Type
FXDQ-
PVE 20P 25P 32P — — — — — —
FXDQ-
PVET 20P 25P 32P — — — — — —
FXDQ-
NAVE 20NA 25NA 32NA 40NA 50NA 63NA — — —
FXDQ-
NVET 20N 25N 32N 40N 50N 63N — — —
Ceiling Mounted
Built-In Type FXSQ 20M 25M 32M 40M 50M 63M 80M 100M 125M
Ceiling Mounted
Duct Type FXMQ — — — 40MA 50MA 63MA 80MA 100MA 125MA
Ceiling Suspended
Type FXHQ — — 32MA — — 63MA — 100MA —
Wall Mounted Type FXAQ 20MA 25MA 32MA 40MA 50MA 63MA — — —
Floor Standing Type FXLQ 20MA 25MA 32MA 40MA 50MA 63MA — — —
Concealed Floor
Standing Type FXNQ 20MA 25MA 32MA 40MA 50MA 63MA — — —
Ceiling Suspended
Cassette Type FXUQ — — — — — — 71MA 100MA 125MA

Si34-603
Specifications 5
Part 2
Specifications
1. Specifications ..........................................................................................6
1.1 Outdoor Units ...........................................................................................6
1.2 Indoor Units ............................................................................................10

Specifications Si34-603
6Specifications
1. Specifications
1.1 Outdoor Units
Heat Pump 50/60Hz <RXYMQ-PVE>
Notes:
1 Indoor temp. : 27°CDB, 19°CWB / outdoor temp. : 35°CDB / Equivalent piping length : 7.5m, level
difference : 0m.
2 Indoor temp. : 20°CDB / outdoor temp. : 7°CDB, 6°CWB / Equivalent piping length : 7.5m, level difference
: 0m.
Model Name RXYMQ4PVE RXYMQ5PVE


1 Cooling Capacity
kcal / h 9,600 12,000
Btu / h 38,200 47,800
kW 11.2 14.0


2 Heating Capacity
kcal / h 10,800 13,800
Btu / h 42,700 54,600
kW 12.5 16.0
Casing Color Ivory White Ivory White
Dimensions: (H×W×D) mm 1,345×900×320 1,345×900×320
Heat Exchanger Cross Fin Coil Cross Fin Coil
Comp.
Type Hermetically Sealed Scroll Type Hermetically Sealed Scroll Type
Piston Displacement m³/h 19.36 19.36
Number of Revolutions r.p.m 6,480 6,480
Motor Output×Number
of Units kW 2.5×1 3.0×1
Starting Method Direct on line Direct on line
Fan
Type Propeller Fan Propeller Fan
Motor Output W 70×270×2
Air Flow Rate m³/min 106 106
Drive Direct Drive Direct Drive
Connecting
Pipes
Liquid Pipe mm φ9.5 (Flare Connection) φ9.5 (Flare Connection)
Gas Pipe mm φ15.9 (Flare Connection) φ15.9 (Flare Connection)
Machine Weight kg 125 125
Safety Devices High Pressure Switch, Fan Driver Overload Protector,
Inverter Overload Protector, Fusible Plugs, Fuse High Pressure Switch, Fan Driver Overload Protector, Inverter Overload Protector, Fusible Plugs, Fuse
Defrost Method Reverse cycle defrosting Reverse cycle defrosting
Capacity Control % 24~100 24~100
Refrigerant
Refrigerant Name R-410A R-410A
Charge kg 4.0 4.0
Control Electronic Expansion Valve Electronic Expansion Valve
Refrigerator
Oil
DAPHNE FVC68D DAPHNE FVC68D
Charge Volume L 1.5 1.5
Standard Accessories Installation Manual, Operation Manual, Clamps Installation Manual, Operation Manual, Clamps
Drawing No. C: 4D052608
Conversion Formulae
kcal/h=kW×860
Btu/h=kW×3412
cfm=m³/min×35.3

Si34-603 Specifications
Specifications 7
Notes:
1 Indoor temp. : 27°CDB, 19°CWB / outdoor temp. : 35°CDB / Equivalent piping length : 7.5m, level
difference : 0m.
2 Indoor temp. : 20°CDB / outdoor temp. : 7°CDB, 6°CWB / Equivalent piping length : 7.5m, level difference
: 0m.
Model Name RXYMQ6PVE


1 Cooling Capacity
kcal / h 13,300
Btu / h 52,900
kW 15.5


2 Heating Capacity
kcal / h 15,500
Btu / h 61,400
kW 18.0
Casing Color Ivory White
Dimensions: (H×W×D) mm 1,345×900×320
Heat Exchanger Cross Fin Coil
Comp.
Type Hermetically Sealed Scroll Type
Piston Displacement m³/h 19.36
Number of Revolutions r.p.m 6,480
Motor Output×Number
of Units kW 3.5×1
Starting Method Direct on line
Fan
Type Propeller Fan
Motor Output W 70×2
Air Flow Rate m³/min 106
Drive Direct Drive
Connecting
Pipes
Liquid Pipe mm φ9.5 (Flare Connection)
Gas Pipe mm φ19.1 (Brazing Connection)
Machine Weight kg 125
Safety Devices High Pressure Switch, Fan Driver Overload Protector,
Inverter Overload Protector, Fusible Plugs, Fuse
Defrost Method Reverse cycle defrosting
Capacity Control % 24~100
Refrigerant
Refrigerant Name R-410A
Charge kg 4.0
Control Electronic Expansion Valve
Refrigerator
Oil
DAPHNE FVC68D
Charge Volume L 1.5
Standard Accessories Installation Manual, Operation Manual, Clamps,
Auxiliary Piping
Drawing No. C: 4D052608
Conversion Formulae
kcal/h=kW×860
Btu/h=kW×3412
cfm=m³/min×35.3

Specifications Si34-603
8Specifications
Cooling Only 50/60Hz <RXMQ-PVE>
Notes:
1 Indoor temp. : 27°CDB, 19°CWB / outdoor temp. : 35°CDB / Equivalent piping length : 7.5m, level
difference : 0m.
Model Name RXMQ4PVE RXMQ5PVE


1 Cooling Capacity
kcal / h 9,600 12,000
Btu / h 38,200 47,800
kW 11.2 14.0
Casing Color Ivory White Ivory White
Dimensions: (H×W×D) mm 1,345×900×320 1,345×900×320
Heat Exchanger Cross Fin Coil Cross Fin Coil
Comp.
Type Hermetically Sealed Scroll Type Hermetically Sealed Scroll Type
Piston Displacement m³/h 19.36 19.36
Number of Revolutions r.p.m 6,480 6,480
Motor Output×Number
of Units kW 2.5×1 3.0×1
Starting Method Direct on line Direct on line
Fan
Type Propeller Fan Propeller Fan
Motor Output W 70×270×2
Air Flow Rate m³/min 106 106
Drive Direct Drive Direct Drive
Connecting
Pipes
Liquid Pipe mm φ9.5 (Flare Connection) φ9.5 (Flare Connection)
Gas Pipe mm φ15.9 (Flare Connection) φ15.9 (Flare Connection)
Machine Weight kg 125 125
Safety Devices High Pressure Switch, Fan Driver Overload Protector,
Inverter Overload Protector, Fusible Plugs, Fuse High Pressure Switch, Fan Driver Overload Protector, Inverter Overload Protector, Fusible Plugs, Fuse
Defrost Method Reverse cycle defrosting Reverse cycle defrosting
Capacity Control % 24~100 24~100
Refrigerant
Refrigerant Name R-410A R-410A
Charge kg 4.0 4.0
Control Electronic Expansion Valve Electronic Expansion Valve
Refrigerator
Oil
DAPHNE FVC68D DAPHNE FVC68D
Charge Volume L 1.5 1.5
Standard Accessories Installation Manual, Operation Manual, Clamps Installation Manual, Operation Manual, Clamps
Drawing No. C: 4D052613
Conversion Formulae
kcal/h=kW×860
Btu/h=kW×3412
cfm=m³/min×35.3

Si34-603 Specifications
Specifications 9
Notes:
1 Indoor temp. : 27°CDB, 19°CWB / outdoor temp. : 35°CDB / Equivalent piping length : 7.5m, level
difference : 0m.
Model Name RXMQ6PVE


1 Cooling Capacity
kcal / h 13,300
Btu / h 52,900
kW 15.5
Casing Color Ivory White
Dimensions: (H×W×D) mm 1,345×900×320
Heat Exchanger Cross Fin Coil
Comp.
Type Hermetically Sealed Scroll Type
Piston Displacement m³/h 19.36
Number of Revolutions r.p.m 6,480
Motor Output×Number
of Units kW 3.5×1
Starting Method Direct on line
Fan
Type Propeller Fan
Motor Output W 70×2
Air Flow Rate m³/min 106
Drive Direct Drive
Connecting
Pipes
Liquid Pipe mm φ9.5 (Flare Connection)
Gas Pipe mm φ19.1 (Brazing Connection)
Machine Weight kg 125
Safety Devices High Pressure Switch, Fan Driver Overload Protector,
Inverter Overload Protector, Fusible Plugs, Fuse
Defrost Method Reverse cycle defrosting
Capacity Control % 24~100
Refrigerant
Refrigerant Name R-410A
Charge kg 4.0
Control Electronic Expansion Valve
Refrigerator
Oil
DAPHNE FVC68D
Charge Volume L 1.5
Standard Accessories Installation Manual, Operation Manual, Clamps,
Auxiliary Piping
Drawing No. C: 4D052613
Conversion Formulae
kcal/h=kW×860
Btu/h=kW×3412
cfm=m³/min×35.3