Daintree GE current Lumination LPL Gen D Series User manual

Installation Guide
IND676 | DOC-2002763
Lumination® LED Luminaire
LPL Gen D Series
BEFORE YOU BEGIN
Read these instructions completely and carefully.
Save These Instructions
Use only in the manner intended by the manufacturer.
If you have any questions, contact the manufacturer.
Prepare Electrical Wiring
Electrical Requirements
• The LED luminaire must be connected to the mains
supply according to its ratings on the product label.
• Class 1 wiring should be in accordance with NEC.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
CAN ICES-005(A)/NMB-005(A) Grounding Instructions
• The grounding and bonding of the overall system
shall be done in accordance to local electric code of
the country where the luminire is installed.
Note: This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the FCC
Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
WARNING / AVERTISSEMENT
RISK OF ELECTRIC SHOCK
• Turn power off before inspection, installation or removal.
• Properly ground electrical enclosure.
RISK OF FIRE
• Follow all NEC and local codes.
• Use only UL approved wire for input/output connections.
Minimum size 18 AWG (0.75mm2).
• Do not install insulation within 3 inches (76 mm) of luminaire top.
RISQUES DE DÉCHARGES ÉLECTRIQUES
• Coupez l’alimentation avant d’inspecter, installer ou déplacer le luminaire.
• Assurez-vous de correctement mettre à la terre le boîtier d’alimentation électrique.
RISQUES D’INCENDIE
• Respectez tous les codes NEC et codes locaux.
• N’utilisez que des fils approuvés par UL pour les entrées/sorties de connexion.
Taille minimum 18 AWG (0.75mm2).
• Maintenir une distance de 76 mm (3 pouces) entre le luminaire et l’isolant.
1

4
Lumination® LPL Gen D Series Installation Guide
Luminaire Installation
TURN OFF POWER at the source to the
luminaire.
1Default lumen level is M(medium), and default CCT is
4000K. For other lumen level or CCT, loosen screw and
remove switch cover, then set switch to the desired
lumen level or CCT by screwdriver. Re-attach cover and
tighten screw.
2
LPL22x Series
Connection hole
for safety cable
T-Bar
T-Bar
Bracket on the housing
LPL24x Series
Bend the brackets on the housing to make sure
they hook to T-Bar.
Secure safety cable to connection hole as needed
to meet local seismic requirements. Safety cable
and method of attachment to the building are
provided by contractor according to local
building codes.
T-Bar
3Insert luminaire into T-bar ceiling grid. Unit should
not move freely within the ceiling grid. To ensure a
consistent appearance, align fixtures in the same
orientation throughout the ceiling pattern.
22
CCT switch Switch cover
Lumen switch
Screw
Sensor enclosure
(optional)
Sensor enclosure
(optional)
K.O. for EMBB only
K.O. for EMBB only

1
2
Lumination® LPL Gen D Series Installation Guide
Electrical Connections - Basic version
Optional Installation: 0-10V Volt Dimming
Remove electrical enclosure cover with three Knock-Outs on the top. Carefully remove knockout for AC mains input wires. Install
UL listed electrical fittings in the knockout holes for wire protection.
Connect the AC mains to the black (line) and white (neutral) input wires of the fixture by using UL listed connectors or wire-nuts
for 14-18 AWG.
Connect the ground wire to the green-yellow ground wire of luminaire. When connecting dimming controller, wires must run
through a separate knockout hole equipped with an appropriate wire restraint or cable gland. Then, re-attach and fix electrical
enclosure cover with screw by screwdriver.
Option: Follow diagram for 0-10V. Run wires from controller through a different knockout than the AC input wire. At the output
side of fixture, make appropriate connections by using UL listed connectors or wire-nuts. To combine with LFAMBA0VQFAEL,
LCAMBA0NRFAEL, LCAMBA0TSFAEL, LCAMBA0TQFAEL, LFAMBADVQFA, LCAMBA0NRFAB2,LCAMBA0TSFAB2, LCAMBA0TQFAB2,
LCAMBA0NRFA, LCAMBA0TSFA or LCAMBA0TQFA, please follow the installinstructions provided with those products.
NOTE: Please cover dimming leads with wire nuts if leads not be connected.
3
Fixture
Green/Yellow
White
Line
Neutral
Ground
1-10V(+)
1-10V(-) To 0-10V
Dimmer
Violet
Pink
3
Electrical enclosure cover AC mains Dimming
AC Mains
Black

1
Lumination® LPL Gen D Series Installation Guide
Electrical Connections - Sensor version
Remove sensor enclosure cover. Carefullyremove knockout for AC mains input wires. Install UL listed electrical fttings in
the knockout holes for wire protection.
LPL22x
Connect the AC mains to the black (line) and white (neutral) input wires of the LED driver by using UL listed connectors or wire-nuts
for 18-14 AWG.
LPL24x
Connect the AC mains to the brown (line) and blue (neutral) input wires of the LED driver by using UL listed connectors or wire-nuts
for 18-14 AWG.
Connect the ground wire to the green-yellow ground wire of luminaire. When connecting dimming controller, wires must run
through a separate knockout hole equipped with an appropriate wire restraint or cable gland. Then, re-attach and fix enclosure cover
with screw by screw driver.
www.gecurrent.com
©2020 Current Lighting Solutions, LLC. All rights reserved. GE and the GE monogram are trademarks of the
General Electric Company and are used under license. Information provided is subject to change without
notice. All values are design or typical values when measured under laboratory conditions.
IND676 REV-A
Fixture
Line
Neutral
Ground
4
Sensor enclosure cover AC mains
Green/Yellow
White (or Blue)
AC Mains
Black (or Brown)