Dakota Alert DCR-4000 User manual

Wireless Receiver
DCR-4000
USER GUIDE
www.dakotaalert.com
Dakota Alert®
WIRELESS SECURITY EQUIPMENT
TM

2

3
PACKAGE CONTENTS
• Receiver
• Power adapter
• User Guide
POWERING YOUR RECEIVER
1. Connect the power adapter to the bottom of the receiver, threading the cord through a
groove in the bottom.
2. Plug the adapter into a power outlet.
Bottom
Power adapter

4
SETTING UP YOUR RECEIVER
Note: You can connect up to 16 transmitters to your receiver.
1. Place your receiver and transmitter next to each other.
Note: Be careful not to activate your transmitter until you nd the tune you want. If your transmitter is a
motion sensor, consider covering the sensor to avoid accidentally activating it.
2. Press and hold the MODE and (volume) buttons for three seconds. When all four LEDs
ash, release the buttons.
Speaker
Mode
LEDs
Volume

5
3. Press (volume) repeatedly until you nd the tune you want to use.
1 Ding Dong (high) 5 Alarm/Siren 9 William Tell
2 Ding Dong (low) 6 Coo Coo Clock 10 Cannon in D
3 Westminster 7 Bird Chirping 11 Morning
4 Fur Elise 8 Twinkle Twinkle 12 Toreador March
4. After you choose a tune, activate the transmitter (for example, press its button or activate
the motion sensor). The receiver emits a short beep.
Note: If you accidentally activate the transmitter on a tune you don’t want, press the (volume) button
to continue cycling through the tunes to select the tune you want, then reactive the transmitter.
5. If you are coding more than one transmitter, repeat steps 3 and 4.
6. After your transmitter(s) are coded, press and hold the MODE button until the LEDs stop
ashing.
7. To test the transmitter tune, activate the transmitter. You’ll hear the selected tune through
your receiver and the LEDs will ash.
ADJUSTING THE VOLUME
• Press the (volume) button repeatedly to adjust the volume (four levels and o). The lights
show the volume level for four seconds.

6
MOUNTING THE RECEIVER
Attach two screws (not included) or nails to your wall 2.6 inches (6.7 cm) apart, then hang your
receiver.
DELETING ALL SENSORS
1. Press and hold the MODE and (volume) buttons for three seconds until the four lights
ash slowly.
2. Press and hold the MODE and (volume) buttons again for ve seconds. The four lights
ash quickly, then turn o. The receiver is reset.
Note: To relearn the sensors, see ”Setting up your receiver” on page 4.

7
SPECIFICATIONS
• Power supply: 12 VDC, 500 mA
• Wireless range: up to 1 mi. (1.6 km)*
*Actual range will vary depending on local terrain and obstructions.
• Dimensions: 3.25 × 1.75 in. (8.25 × 4.45 cm)
• Operating temperature: -30 to 120°F (-34.4 to 48.9°C)
• Operating frequencies: 433 MHz
TECH SUPPORT
If you have problems using this product after reading this manual, please contact us. You can reach us by phone at
605-356-2772 from 8:30 AM to 5:00 PM Monday through Friday (Central Standard Time). We will be happy to answer
your questions and help you in any way we can.
WARRANTY
Dakota Alert warrants this product to be free of defects in materials and workmanship for a period of one year from
the date of purchase. This warranty does not cover damage resulting from accident, abuse, act of God, or improper
operation. If this product does become defective, simply return it to Dakota Alert. Please include a note describing
the troubles along with your name and return address as well as the original sales receipt. If the product is covered
under the warranty it will be repaired or replaced at no charge. If it is not covered by the warranty, you will be
notied of any charges before work is done.
LEGAL NOTICES
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. Changes or modications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment. This equipment has been

Dakota Alert, Inc.
www.dakotaalert.com
Phone: [phone]
Fax: [phone]
Address: 32556 477th Ave. | P0 Box 130 | Elk Point, SD 57025
18-0638
tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment o and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING: Cancer and Reproductive Harm. Go to www.P65Warnings.ca.gov for more information.
Dakota Alert®
WIRELESS SECURITY EQUIPMENT
TM