Dakota Alert WR-3000 User manual

Dakota Alert™
WR-3000
Wireless
Receiver
Owner’s Manual

WR-3000 Receiver
2
3
1
2. 3.
WR-3000 RECEIVER INSTRUCTIONS
WARNING
This device complies with Part 15 of the FCC rules, operation of this device is
subject to the following conditions: 1. This device may not cause harmful in-
terference. 2.This device must accept any interference, including interference
that may cause undesired operation.
INTRODUCTION
The WR-3000 receiver can be used with any of the Dakota Alert 3000 series
transmitters (WMT-3000, WPT-3000, WHT-3000). The WR-3000 plugs in to a
standard wall outlet and can be placed on a table or mounted on the wall.
When the receiver gets a signal from the transmitter one of 4 different tones
(Classical , Westminster Chime, Ding Dong, Whistle) will sound for a few sec-
onds. There is also a volume control so you can set the sound to the desired
level. The receiver is also equipped with 4 form“C”relays (one for each zone)
and one 12 VDC output terminal that will activate for several seconds when a
signal is received.The receiver can be user programmed so the 12VDC termi-
nal and one relay will activate for 10 minutes if this is desired. The tones will
still sound for several seconds.
OPERATION
1. Connect the end of the power supply to the receiver. (1)
2. Plug the power supply into a wall outlet
3. Locate the off/on switch (2) and move to the“on”position.
4. Press the “test” button (3) on the side of the receiver to determine the
level of the volume. Rotate the “volume” knob (4) until you have the
sound desired level.
Transmitter Module
4
5
8
67
}
}

4. 5.
For maximum range between the transmitter and receiver, the receiver
should be mounted horizontally on a wall and as high off the floor as pos-
sible. Although the maximum range is about 3000 feet, things such as hills,
trees, metal siding and stucco can all reduce the range.
CODING THE RECEIVER
1. Open the receiver case by inserting a small screw driver into one of the
pry notches on the side of the case.
2. Gently lift off the front cover.
3. Locate the 8 dip switches (5) on the receiver and make sure they set
identically to the first 8 dip switches (6) on the transmitter. Note: If more
than one transmitter is used with the receiver, the first 8 dip switches of all
transmitters must match the 8 dip switches of the receiver.
NOTE: Whenever a change is made to the time jumper or the dip switches,
the receiver must be turned“OFF”and then back“ON”to operate properly.
CODING THE TRANSMITTER
1. Locate the dip switches in the 3000 series transmitter. (refer to trans-
mitter manual)
2.The first 8 dip switches (6) are for the frequency setting (256 combina-
tions). Set the first 8 switches to match the 8 switches in the receiver.
3. Switches 9 & 10 (7) are for the zone/channel setting on the transmitter.
The four zones are as follows:
TONE, RELAY AND VOLTAGE OUTPUT
1. Each of the four transmitter zones (selectable by switch 9 & 10) will
sound a tone and activate the corresponding relay on the receiver.
2. Each of the form“C”relays is rated for 24 VDC at 3 Amp maximum current.
3.The 12 VDC output will activate when the transmitter is set to zone 1.The
voltage duration will last for four seconds and has a maximum current of
400mA.
Switch 9 Switch 10 Channel Tune
ON ON 1+12VDC Classical
OFF ON 2 Westminster
ON OFF 3 Ding Dong
OFF OFF 4 Whistle

6.
4. The channel 1 relay and the 12 VDC output can be set to operate for
4 seconds or 10 minutes. To change the duration, locate the jumper (8)
on the upper right hand corner of the circuit board. When the jumper is
covering both pins,the output time is 4 seconds.When the jumper is only
covering one pin,the output time will be 10 minutes.
NOTE: Whenever a change is made to the time jumper or the dip switches,
the receiver must be turned“OFF”and then back“ON”to operate properly.
For maximum range between the transmitter and receiver, the receiver
should be mounted horizontally on a wall and as high off the floor as pos-
sible. Although the maximum range is about 3000 feet, things such as hills,
trees, metal siding and stucco can all reduce the range.
Frequency: 433.92 MHz
Operating voltage: 12VDC
12 volt DC output current: 400 mA maximum
Relay output rating: 24VDC at 3 Amp
TECHNICAL SUPPORT
If you encounter any difficulty in the operation of this product after reading
the manual, please contact us. You can reach us by phone at 605-356-2772
from 8:30 AM to 5:00 PM Monday through Friday (Central Standard Time).We
will be happy to answer your questions and help you in any way we can.
WARRANTY
Dakota Alert warrants this product to be free of defects in material and work-
manship for a period of one year from the date of purchase. This warranty
does not cover damage resulting from accident,abuse,act of God or improp-
er operation.
If this product does become defective,simply return it to Dakota Alert.Please
include a note describing the troubles along with your name and return ad-
dress as well as the original sales receipt.If the product is covered under war-
ranty it will be repaired or replaced at no charge. If it is not covered by war-
ranty, you will be notified of any charges before work is done.
7.

Dakota Alert, Inc.
109 W. Main St.
P0 Box 130
Elk Point, SD 57025
Phone: [phone]
Fax: [phone]
Web: www.dakotaalert.com