Dakota Digital Odyssey II Series User manual

Series II
ODYR-04 & SLX-04 WATER TEMPERATURE
Introduction:
The Odyssey Series II gauges from Dakota Digital, Inc. incorporates the reliability and
quality of our standard gauges, along with several unique features and easy mounting. These
features include:
•Industry standard 2-1/16” gauge size.
•A warning feature that flashes the gauge readout when outside operating limits.
•User adjustable warning points.
•Microprocessor stabilized readings.
•Quick-Start feature to provide accurate readings quickly after being powered up.
•Night dimming with lens label lighting.
•Non-Glare, high contrast lens.
•High Visibility VFD display for sunlight readability.
Operation:
The PWR terminal should be connected to a 12 volt accessory feed. The case provides
the gauge ground. Connect a ground wire to the screw at the bottom rear of the case. When the
DIM terminal has 12 volts, it will dim the display for night viewing. The SND terminal is the
temperature sender input. The sender must be a Dakota Digital 300F temp unit. Sending
units from other manufacturers will cause incorrect readings. If a sender is not connected
properly, the display will show “EEE”. If the SND terminal is shorted to ground, the display will
show “---”.
The water temperature gauge will operate and read correctly between the temperature
range of 0 - 300°F(0 - 150°C). Because of the wide temperature span, the gauge may not be as
accurate below 75°F (24°C). The gauge has a user adjustable high warning level. This can be
set to indicate when the engine is beginning to overheat.
Setting the warning limits and sender setup:
The SND terminal is used to enter and change the warning settings. You will need a wire
connected to the SND terminal that can be momentarily grounded while you watch the gauge.
The headlights should be off or the DIM terminal unhooked so that it does not interfere with the
setup.
1. To enter the set mode, turn the key on with the SND wire not grounded. The gauge will
display “SEt”.
2. Ground the SND wire. The gauge will display “Snd”. (If you wait too long the gauge will
exit the setup routine and you will need to repeat step #1).
3. Release the SND wire. The gauge will display the current setup. “30F” is for °F and
“15C” is for °C. “40F” and “20C” are for higher temp. rated senders.
4. Each time you momentarily ground the SND wire the setup will change.
5. When the desired setup value is displayed, keep the SND wire grounded for about 2
seconds. The gauge will display “ HI”.
6. Release the SND wire. The gauge will display a number between 131 - 260 (55 - 126C).
7. Each time you momentarily ground the SND wire the number will change.
8. When the desired high warning value is displayed, keep the SND wire grounded for
about 2 seconds. The gauge will display “--”.
9. Turn the key off.

Wiring:
PWR - connect to 12 volt power.
(An accessory terminal will work for this.)
DIM - connect to the tail light circuit.
SND - connect to the temperature sender.
Gauge case - connect to a main ground location
PWR
SND
DIM
FOR GROUND CONNECTION
Sender mounting:
The currently available sender sizes are:
½” NPT SEN-04-4
3/8” NPT SEN-04-2
1/8” NPT SEN-04-1
M10X1 SEN-04-5
M12X1.5 SEN-04-6
M14X1.5 SEN-04-7
M16X1.5 SEN-04-8
Other sizes may be available by special order.
These senders have a tapered self-sealing thread. The engine and sender threads should be
cleaned before installation and no tape or sealant should be used on the threads. The sender
should be mounted in the engine block or in the intake manifold. Installing in the cylinder head
can cause high readings due to the exhaust manifold heat. Make sure that the sender tip can get
into the coolant flow.
Mounting:
The gauge requires a round hole 2-1/16” in diameter. It should be inserted into the
opening from the front and the U-clamp will be installed from the back. Tighten the two nuts on
the U-clamp so that the gauge is secure. Gauge depth to the back of the case is 1”. Gauge
depth including the mounting studs is 1-7/8”.

Troubleshooting guide.
Problem Possible cause Solution
Gauge will not light up PWR terminal does not Connect to a location that has power.
have power.
The gauge case is not getting Connect the ground to a different location.
a good ground.
Gauge is damaged. Return gauge for service. (see instructions)
Gauge lights up, but does Loose connection on SND Reconnect wire.
not read correctly. terminal.
Poor ground connection. Move ground to different location
Gauge is sender setup See “Setting sender setup” in the
is incorrect. manual.
Voltage or wiring problem Check wiring harness for loose or damaged
in vehicle wiring harness. wires.
Gauge lights up, but displays Gauge is damaged. Gauge must be returned for service.
“Er0”. (see instructions)
Gauge lights up, but displays SND terminal is shorted to Check wire for damaged insulation. Replace
“---”. ground. If necessary.
Sender is damaged. Replace sender.
Gauge lights up, but displays Sender is not connected Connect SND terminal on gauge to
sender
“EEE”. to gauge. terminal.
Wire between gauge and Test and replace wire.
sender is broken.
Sender is not grounding Sender grounds through it’s mounting
properly. threads. Make sure the threads are
clean. Do Not Use Tape or Sealant
on Sender Threads.
Sender is damaged. Replace sender.
Gauge is damaged. Return gauge for service. (see instructions)
Gauge lights up, but displays Gauge is sender setup See “Setting sender setup” in the
“Er4”. needs to be reset. manual.
Gauge lights up, but displays Gauge warning points need See “Setting the warning limits” in the
“Er5”. to be reset. manual.
Gauge flashes constantly. Warning limits are not set Reset warning limits.
properly.
Vehicle is overheating. Check coolant system.
Gauge will not dim. DIM terminal is not connected Check wiring connections.
correctly.
Gauge remains dim at all DIM terminal is getting power Connect DIM wire to location that only
times. all of the time. has power when the headlights are on.
Battery is very low. Recharge or replace vehicle battery.
Gauge is damaged. Return gauge for service. (see instructions)
SERVICE AND REPAIR
DAKOTA DIGITAL offers complete service and repair of its product line. In addition, technical
consultation is available to help you work through any questions or problems you may be having installing one of
our units.
Should you ever need to send the unit back for repairs, please package the product in a good quality box
along with plenty of packing material. Ship the product by UPS or insured Parcel Post. Be sure to include a
complete description of the problem, your full name and address (street address preferred), and a telephone
number where you can be reached during the day. An authorization number for products being returned for
repair is not needed. Do not send any money. We will bill you for the repair charges. Any returns for warranty
work must include a copy of the dated invoice or bill of sale.

Technical specifications
Minimum operating voltage - 7 volts
Maximum operating voltage - 17 volts
(operating at or near maximum voltage for an extended time can damage unit)
Maximum temperature reading - 305°F (150°C)
Gauge Resolution - 1°F (1°C)
Gauge accuracy - ±5°F (±3°C)
Typical current draw (@ 13.8V) - 0.2 A
ODYSSEY SERIES DIGITAL GAUGE LIMITED WARRANTY
DAKOTA DIGITAL (the Company) warrants to the ORIGINAL PURCHASER of this product that should it, under
normal use and condition, be proven defective in material or workmanship within 24 MONTHS FROM THE DATE OF
PURCHASE, such defect(s) will be repaired or replaced (at the Company’s option) without charge for parts or labor
directly related to repairs of the defect(s).
To obtain repair or replacement within the terms of this Warranty, the product is to be delivered with proof of
warranty coverage (e.g. dated bill of sale), name, address, phone number, and specification of defects, transportation
prepaid, to the factory. This Warranty is valid for the original purchaser only and may not be transferred.
This warranty does not cover nor extend to damage to vehicle electrical system. This Warranty does not apply
to any product or part thereof which in the opinion of the Company has been damaged through alteration, improper
installation, mishandling, misuse, neglect, or accident.
This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED WARRANTIES, INCLUDING
ANY IMPLIED WARRANTY OF MERCHANTABLITY, SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN
WARRANTY. ANY ACTION FOR BREACH OF ANY WARRANTY HEREUNDER INCLUDING ANY IMPLIED
WARRANTY OF MERCHANTABLITY MUST BE BROUGHT WITHIN A PERIOD OF 24 MONTHS FROM DATE OF
ORIGINAL PURCHASE. IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR
INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESSED OR IMPLIED,
WHATSOEVER. No person or representative is authorized to assume for the Company any liability other that expressed
herein in connection with the sale of this product.
The Company does not warrant that this product cannot be compromised or circumvented. THE EXTENT OF
THE COMPANY’S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED
ABOVE AND, IN NO EVENT, SHALL THE COMPANY’S LIABILITY EXCEED THE PURCHASE PRICE PAID TO THE
PURCHASER FOR THE PRODUCT.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation if
incidental or consequential damage so the above limitations or exclusions may not apply to you. This warranty gives you
specific legal rights and you may also have other rights which vary from state to state.
4510 W. 61ST St. N., Sioux Falls, SD 57107
Phone: [phone] FAX: [phone]
www.dakotadigital.com
[email protected]
©Copyright 2001 Dakota Digital Inc.