Daktronics All sport 100 User manual

201 Daktronics Drive

Brookings, SD 57006-5128

www.daktronics.com/support

800.325.8766

ALL SPORT®100

CONTROL CONSOLE

OPERATION MANUAL

P1196

ED-13432

Rev 5

9 February 2018

responsibility for errors or omissions. No part of this book covered by the copyrights hereon may be reproduced or copied

in any form or by any means—graphic, electronic, or mechanical, including photocopying, taping, or information

storage and retrieval systems—without written permission of the publisher.

Daktronics trademarks are property of Daktronics, Inc. All other trademarks are property of their respective companies.

– i –

Table of Contents

1 Introduction��1

Important Safeguards ...............................1

Specications Label ..................................1

Resources ...................................................2

Console Revision History............................2

Daktronics Exchange and Repair &

Return Programs ........................................2

Exchange Program ��2

Repair & Return Program ��3

Daktronics Warranty & Limitation of

Liability��3

2 Basic Operation ��4

Console Operation....................................4

Sport Inserts.................................................4

Start Up .......................................................4

Standard Keys ............................................5

Start ��5

Stop��5

Enter/Edit ��5

Clear/Alt��5

Set Time ��5

Up/Down (Alt� Function)��6

Manual Horn ��6

Auto Horn (Alt� Function) ��6

Dim (Alt� Function)��6

3 Clock/Score Operation ��8

Clock/Score Keys.......................................8

Score (+2/+1/-1)��8

Period +1 ��8

Bonus ��8

Possession/Serve ��9

4 Baseball Operation ��10

Baseball Keys............................................10

Score (+1/-1)��10

Hit ��10

Error��10

Ball +1, Strike +1, Clear Ball/Strike ��10

Out +1 ��11

Inning +1��11

5 Segment Timer Operation��12

Segment Timer Information ....................12

Segment Timer Keys ................................12

Segment Number & Time��12

First/Last Segment��13

Interval Time��13

Current Segment +1 ��13

Reset Current Segment ��14

Reset to 1st Segment��14

Warning Time ��14

Copy Range��14

Auto Stop��14

Set Program��15

TI-2025 & TI-2026 Segment Timers...........15

Sending Program Information to the

Display��15

Play Clock (Program 6)��16

Two-Minute Drill (Program 7) ��16

RC-50 Controls ��16

Segment Timer (Programs 1-5) ........16

Play Clock (Program 6) ....................17

Two-Minute Drill (Program 7)............17

A Sport Inserts ��19

B Daktronics Warranty and Limitation

of Liability��25

This page intentionally left blank.

Introduction

1

1 Introduction

This manual explains the operation of the All Sport®100 control console and the RC-50

wireless radio controller for segment timing functions. For additional information regarding

the safety, installation, operation, or service of this system, refer to the telephone numbers

listed in Daktronics Exchange and Repair & Return Programs (p� 2).

Important Safeguards

• Read and understand all instructions, both general and for specic sports.

• Do not drop the control console or allow it to get wet�

• This device shall not be exposed to dripping or splashing, and no objects lled with

liquid shall be placed upon it�

WARNING! To reduce the risk of re or electric shock, do not expose this device to

rain or moisture�

• Never yank the power cord to pull the plug from the outlet� Grasp the plug and pull to

disconnect�

• Do not let the power cord touch hot surfaces or hang over the edge of a table that

would damage or cut the cord�

• If an extension cord is necessary, use a three-pronged, polarized cord� Arrange the

cord with care so that it will not be tripped over or pulled out�

• Before using an extension cord, inspect the cable thoroughly and verify its

compliance with the local electric codes�

• Do not disassemble control equipment or electronic controls of the display; failure to

follow this safeguard will make the warranty null and void�

• Inspect console for shipping damage such as rattles and dents, and verify that all

equipment is included as itemized on the packing slip� Immediately report any

problems to Daktronics; save all packing materials if exchange is necessary�

All Sport 100 control consoles receive external power from a wallpack power adapter or

through a 20' (6.1 m) long cable plugged directly into a portable scoreboard. The same

cable (part # 0A-1196-0095) also provides signal from the controller to the scoreboard.

RC-50 wireless handheld controllers receive power via an internal 3V lithium battery.

Specications Label

Serial and model number information can be found on an ID label on the device. Refer

to Figure 1.

When calling Daktronics customer service, please have the model number, serial

number, and the date the device became operational available to ensure the request is

serviced as quickly as possible.

ASSY NO.

SER. NO.

MFG DATE

BROOKINGS, SD 57006-5128 PHONE 800-325-8766 LL-2305 R01

201 DAKTRONICS DR.

DAKTRONICS

Figure 1: Specications Label

Introduction

2

Resources

Figure 2 illustrates a Daktronics drawing

label. This manual refers to drawings by

listing the last set of digits. In the example,

the drawing would be referred to as

DWG-1007804. All references to drawing

numbers, appendices, gures, or other

manuals are presented in bold typeface.

Any drawings referenced in a particular

section are listed at the beginning of it as

shown below:

Reference Drawing:

System Riser Diagram....................................................................................... DWG-1007804

Daktronics identies manuals by the DD or ED number located on the cover page.

Console Revision History

For a complete history of revisions to the console rmware, refer to All Sport & OmniSport

Revision Histories (DD3679410), available online at www.daktronics.com/manuals.

Daktronics Exchange and Repair & Return Programs

Exchange Program

The Daktronics Exchange Program is a service for quickly replacing key components

in need of repair. If a component fails, Daktronics sends a replacement part to the

customer who, in turn, returns the failed component to Daktronics. This decreases

equipment downtime. Customers who follow the program guidelines explained below

will receive this service.

Before contacting Daktronics, identify these important numbers:

Assembly Number: ___________________________________________________________________

Job/Contract Number: _______________________________________________________________

Date Manufactured/Installed: _________________________________________________________

Daktronics Customer ID Number: ______________________________________________________

To participate in the Exchange Program, follow these steps:

1� Call Daktronics Customer Service�

Market Description Customer Service Number

Schools (including community/junior colleges), religious

organizations, municipal clubs, and community centers

877-605-1115

Fax: 605-697-4444

Universities and professional sporting events, live events for

auditoriums, and arenas

866-343-6018

Fax: 605-697-4444

2� When the new exchange part is received, mail the old part to Daktronics�

If the replacement part xes the problem, send in the problem part being replaced.

Drawing Number

Figure 2: Drawing Label

Introduction

3

a� Package the old part in the same shipping materials in which the replacement

part arrived.

b� Fill out and attach the enclosed UPS shipping document.

c� Ship the part to Daktronics.

3� The defective or unused parts must be returned to Daktronics within 5 weeks of initial

order shipment�

If any part is not returned within ve (5) weeks, a non-refundable invoice will be

presented to the customer for the costs of replenishing the exchange parts inventory

with a new part. Daktronics reserves the right to refuse parts that have been

damaged due to acts of nature or causes other than normal wear and tear.

Repair & Return Program

For items not subject to exchange, Daktronics offers a Repair & Return Program. To send

a part for repair, follow these steps:

1� Call or fax Daktronics Customer Service�

Refer to the appropriate number in the chart on the previous page.

2� Receive a case number before shipping�

This expedites repair of the part.

3� Package and pad the item carefully to prevent damage during shipment�

Electronic components, such as printed circuit boards, should be placed in an

antistatic bag before boxing. Daktronics does not recommend using packing

peanuts when shipping.

4� Enclose:

• name

• address

• phone number

• the case number

• a clear description of symptoms

5� Ship to:

Daktronics Customer Service

[Case #]

201 Daktronics Drive, Dock E

Brookings, SD 57006

Daktronics Warranty & Limitation of Liability

The Daktronics Warranty & Limitation of Liability is located at the end of this manual. The

Warranty is independent of Extended Service agreements and is the authority in matters

of service, repair, and display operation.

Basic Operation

4

2 Basic Operation

Console Operation

The console face consists of a 2-line by

16-character liquid crystal display (LCD) and an

area for a sport-specic insert. Refer to Figure 3.

The standard keys and functions common to all

sports are explained in Standard Keys (p� 5). All

of the keys that pertain to a specic sport code

insert are explained in detail in their respective

sport section.

Throughout this manual, the names or letters

of keys on the keypad are enclosed in angle

brackets (such as <ENTER*>).

Sport Inserts

Sport inserts allow one console to control multiple sports. To use an insert, slide it into the

opening on the bottom of the console until it stops. To remove a sport insert, pull on the

tab that extends from the bottom of the console.

If an insert is lost or damaged, a printed copy of the insert drawing from Appendix A may

be used until a replacement can be ordered.

A sport insert identies the keys required for normal operation of a specic sport. In most

cases, pressing a key immediately changes the scoreboard. Keys that require entry

of additional information are marked by a dot (such as <SET TIME •>). This additional

information is usually a number followed by the <ENTER*> key.

Some keys are labeled +1 or +2. By pressing one of these keys once, the corresponding

eld on the scoreboard (such as score or period) “increments”, or increases, by one. A

key with -1 “decrements”, or decreases, by one.

On most inserts, certain keys have been grouped together in green (Home) or red

(Guest). These keys are team keys and work the same for both teams. They affect the

statistics only for that one team. Keys not under one of these color groups are game keys.

They are general keys for the progress of the game (such as period or quarter).

Keys with arrows activate an indicator (possession, bonus, etc.) on the scoreboard. The

direction of the arrow selects the appropriate team (left for home, right for guest).

Start Up

Use the switch on the back of the console to turn it on, then follow the LCD screens:

Display Action

ALL SPORT 100

ED-13375 VER 1.7

The console turns on as soon as external power is applied.

The console performs a self-test when it is powered on. During

the self-test, a message displays the version of the standard

software loaded in the console.

VER = version number and revision number

ED = standard software number

LCD

Horn

Control

Menu

Navigation

Clock

Control

Number

Keypad

Sport-Speciﬁ c Insert

LCD

Horn

Control

Menu

Navigation

Clock

Control

Number

Keypad

Sport-Speciﬁ c Insert

LCD

Sport-

Speciﬁ c

Insert

LCD

Figure 3: All Sport 100

Basic Operation

5

Display Action

ENTER CODE 01

CLOCK/SCORE

ENTER CODE 03

BASEBALL

ENTER CODE 06

SEGMENT TIMER

When the self-test completes, a prompt displays the code

entered into the console.

• To resume the previous code, simply press <ENTER*>.

• To enter a new code, press <CLEAR> to remove the previous

code, use the number keys to enter the new two-digit code

from the available choices shown at left, and then press

<ENTER*>.

In order to change sport codes again, external power must be

removed then reapplied.

Standard Keys

Start

Press <START> to start the main clock.

Stop

Press <STOP> to stop the main clock.

Enter/Edit

The <ENTER*>/<EDIT> key has two main functions. When editing game data, pressing

this key will accept the new data and exit the edit mode. If not in Edit mode, this key

allows selection of the item to be edited, such as team score. After pressing the <EDIT>

key, the operator then presses another key to edit the desired eld on the scoreboard.

The operator enters the new value to display using the number keys and then presses

<ENTER*> to accept.

Clear/Alt

The <CLEAR>/<ALT> key has two main functions. When editing game data, pressing this

key will clear the data being edited or, if pressed twice, will exit the edit mode. When not

in Edit mode, pressing this key followed by a key with an alternate function will initiate the

secondary function.

Set Time

Display Action

TIME EDIT SET

CURR MM:SS.T*

MM:SS.T = minutes, seconds,

tenths of a second

After the main clock has been stopped, press <SET TIME •> to

display the current time of the main clock.

To change the time, enter the desired value using the number

keys, and then press <ENTER*>.

Press <CLEAR> twice to clear changes and return to the game.

Basic Operation

6

Display Action

MAIN CLOCK -EDIT

PERIOD MM:SS *

MM:SS = minutes, seconds

Press <SET TIME •> two times to display the congured time for

the main clock period length.

To set the period length as the new main clock time, press

<ENTER*>. To decline the selection of the period length, press

<CLEAR>.

To change the period length and set the main clock, enter the

new time in minutes and seconds using the number keys, and

then press <ENTER*>.

Press <CLEAR> twice to clear changes and return to the game.

Up/Down (Alt� Function)

Display Action

MAIN CLOCK-DOWN}

1-UP 2-DOWN

After the main clock has been stopped, the direction of the

clock can be set.

Press <ALT> followed by <SET TIME •> and then press <1> or <2>

to select UP or DOWN (default).

Note: The current direction of the main clock is shown by the

arrow on the top line of the LCD.

The <UP/DOWN> alternate function is disabled while the clock is

already running.

Manual Horn

Press <MANUAL HORN> to sound the main horn. The horn sounds as long as the key is

pressed. This key is not available for baseball mode.

Auto Horn (Alt� Function)

Display Action

AUTO HORN- ON

1-ON, 2-OFF

Press <ALT> followed by <MANUAL HORN> and then press <1> or

<2> to select ON (default) or OFF.

Note: A lowercase “h” is shown on the top line of the LCD to

indicate auto horn is enabled.

This key is not available for baseball mode.

Dim (Alt� Function)

Display Action

SELECT DIMMING

1-AUTO 2-MANUAL

Press <ALT> followed by <DIM> to access the scoreboard

dimming menu.

• If the display is equipped with a light sensor, press <1> to

select automatic dimming.

• If the display is not equipped with a light sensor, press <2> to

select manual dimming.

Basic Operation

7

Display Action

MAX INTENSITY

LEVEL(0-3): NONE

DIMMING

LEVEL(0-3): NONE

<0> = none (bright)

<1> = 2/3 (dim)

<2> = 1/2 (dimmer)

<3> = 1/3 (dimmest)

With automatic dimming enabled, press <0>, <1>, <2>, or <3> to

select the maximum intensity for the digits on the scoreboard.

The brightness will never exceed this level, regardless of ambient

lighting conditions. Press <ENTER*> to accept the dimming level.

With manual dimming enabled, press <0>, <1>, <2>, or <3> to set

the intensity for the digits on the scoreboard. If ambient lighting

conditions change, it may be necessary to adjust this setting.

Press <ENTER*> to accept the dimming level.

In general, the scoreboard digits do not need to be as bright at

night as during the day in direct sunlight.

Clock/Score Operation

8

3 Clock/Score Operation

Sport Insert: LL-2550 – Code 01

The Sport Insert drawing is located in Appendix A.

Reference Drawings:

Insert; LL-2550 A/S 100, Clock/Score Code-01 ................................................ DWG-167854

Refer to Section 2: Basic Operation (p� 4) for information on how to start up the

console and use the sport insert. If an insert is lost or damaged, a copy of the insert

drawing can be used until a replacement arrives.

Clock/Score Keys

Score (+2/+1/-1)

Display Action

HOME SCORE + 2

NNN

NNN = current setting

Press the appropriate score key to increment or decrement the

score for the home or guest team.

The LCD shows which key was pressed and the new value for

the team score of the corresponding team.

HOME SCORE

EDIT NNN*

NNN = current setting

Press <EDIT> followed by any score key to display the current

setting. Enter the correct value using the number keys, and then

press <ENTER*>.

Period +1

Display Action

PERIOD N

N = current setting

Press <PERIOD +1> to increment the current period.

The new period number displays briey.

PERIOD

EDIT N*

N = current setting

Press <EDIT> followed by <PERIOD +1> to display the current

setting. Enter the correct value using the number keys, and then

press <ENTER*>.

Bonus

Display Action

HOME BONUS

ON

HOME BONUS

OFF

Press a <BONUS> key to toggle the bonus indicator ON or OFF

for the selected team.

The selected team’s bonus status displays briey.

Clock/Score Operation

9

Possession/Serve

Display Action

HOME POSSESSION

GUEST POSSESSION

Press <POSS/SERVE> to toggle the possession indicator to HOME

or GUEST.

The possession status displays briey.

Note: This key would also be used to illuminate a serve indicator

for volleyball or tennis.

Baseball Operation

10

4 Baseball Operation

Sport Insert: LL-2572 – Code 03

The Sport Insert drawing is located in Appendix A.

Reference Drawings:

Insert; LL-2572 A/S 100, Baseball........................................................................ DWG-184219

Refer to Section 2: Basic Operation (p� 4) for information on how to start up the

console and use the sport insert. If an insert is lost or damaged, a copy of the insert

drawing can be used until a replacement arrives.

Baseball Keys

Score (+1/-1)

Display Action

HOME SCORE + 1

NN

NN = current setting

Press the home/guest <SCORE +1> key to increase the team

score, or press the <SCORE -1> key to decrease the team score.

The LCD shows which key was pressed and the new value.

HOME SCORE

EDIT NN*

NN = current setting

Press <EDIT> followed by any score key to display the current

setting. Enter the correct value using the number keys, and then

press <ENTER*>.

Hit

Display Action

HIT ON

HIT OFF

Press <HIT> to turn on the hit indicator or digits.

Press <HIT> again to turn off the hit indicator or digits.

The hit status displays briey.

Note: When hit is already on, pressing <ERROR> will turn it off.

Error

Display Action

ERROR ON

ERROR OFF

Press <ERROR> to turn on the error indicator or digits.

Press <ERROR> again to turn off the error indicator or digits.

The error status displays briey.

Note: When error is already on, pressing <HIT> will turn it off.

Ball +1, Strike +1, Clear Ball/Strike

Press <BALL +1> or <STRIKE +1> to increment the pitch types. Press <CLEAR BALL & STRIKE>

to immediately reset both values to 0.

Note: If the ball value is 4 when <BALL +1> is pressed, the value is blanked out.

If the strike value is 3 when <STRIKE +1> is pressed, the value is blanked out.

Baseball Operation

11

Out +1

Press <OUT +1> to increment the current number of outs. The new out number appears

immediately on the LCD.

Display Action

OUT EDIT

N*

N = current setting

Press <EDIT> followed by <OUT +1> to display the current setting.

Enter the correct value using the number keys, and then press

<ENTER*>.

Inning +1

Press <INNING +1> to increment the current inning number. The new inning number

appears immediately on the LCD.

Display Action

INNING # EDIT

N *

N = current setting

Press <EDIT> followed by <INNING +1> to display the current

setting. Enter the correct value using the number keys, and then

press <ENTER*>.

Segment Timer Operation

12

5 Segment Timer Operation

Sport Insert: LL-2648 – Code 06

The Sport Insert drawing is located in Appendix A.

Reference Drawings:

Insert; LL-2648 Segment Timer Code 06 ........................................................... DWG-274996

Refer to Section 2: Basic Operation (p� 4) for information on how to start up the

console and use the sport insert. If an insert is lost or damaged, a copy of the insert

drawing can be used until a replacement arrives.

Segment Timer Information

The segment timer is used to time events such as practice sessions. Operation of the

segment timer is determined by 40 segments of pre-programmed length. The segment

timer will count down starting at the segment number that is set as First Segment. When

the rst segment is completed, the timer will count the preset Interval Time and move on

to the next segment. The timer will continue counting segments until the segment number

that is set as Last Segment is complete. It then will reset to the segment saved as the First

Segment and will either begin counting down or wait for the <START> key to be pressed,

depending on the <AUTO STOP> setting. Refer to Auto Stop (p� 14) to set the segment-

stopping feature.

The First Segment and Last Segment values can be used to set up specic practice

sessions. For example, the practice session for one sport could be programmed for

5-minute segments on segments 1–10, while another might use 10-minute segments on

segments 11–20. Set the First Segment and Last Segment values to the desired segment

numbers for the session, and the console will count down each of the segments in order.

It may also be set to either stop on the last segment or loop back to the rst segment

segments, again based on the <AUTO STOP> setting.

The segment values will be saved when the console is turned off.

Segment Timer Keys

Segment Number & Time

Display Action

SEGMENT: NN *

TIME EDIT

NN = current setting

SEGMENT: NN

TIME EDIT MM:SS*

NN = current setting

MM:SS = minutes, seconds

Press <SEG NO • TIME •> to set individual segment times.

Enter the segment to be edited using the number keys, and

then press <ENTER*>.

Enter the time for the segment using the number keys.

Press <ENTER*> to move to the next segment time.

Press <ENTER*> again to exit the function.

Segment Timer Operation

13

First/Last Segment

Display Action

FIRST SEG XX*

LAST SEG YY

XX = current rst segment value

YY = current last segment value

Press <FIRST/LAST SEG>, use the number keys to enter the

segment to be set as the rst segment, and then press <ENTER*>.

Use the number keys to enter the segment to be set as the last

segment, and then press <ENTER*>.

The console will be reset to the segment selected here when the

<RESET TO 1ST SEG> key is pressed. After the segment set as the

last segment is completed, the console will automatically reset

to the segment saved as the rst segment.

Interval Time

The interval time is the time between each segment. The interval time can be displayed

on the scoreboard using the Display Interval function.

Note: If Auto Stop at Each Segment is set to YES, the interval time and display interval

settings will be ignored; the next segment begins whenever the operator presses

<START>.

Display Action

INTERVAL TIME

MM:SS*

MM:SS = minutes, seconds

Press <INTERVAL TIME •> to display the current value of interval

time. Edit the value of the interval time using the number keys,

and then press <ENTER*>.

If the interval time is set to 00:00, no interval time will be

counted, and the menu will be exited.

DISPLAY INTERVAL

1*YES 2-NO

* = current setting

If the interval time entered is greater than 0, the Display Interval

function will appear. This setting determines whether the interval

count will be displayed on the scoreboard.

Press <1> to display the interval time on the scoreboard.

Press <2> to disable the interval time display. The interval time

will be displayed only on the console.

Note 1: Regardless of this setting, the value saved in interval time

will be counted down between segments.

Note 2: When the interval time is being displayed, the segment

number on the scoreboard ashes to indicate that the time

displayed is interval time.

Current Segment +1

Press <CURRENT SEGMENT +1> to move to the next segment. The new segment number

appears immediately on the top line of the LCD.

Display Action

CURRENT SEGMENT:

EDIT NN*

NN = current setting

Press <EDIT> followed by <CURRENT SEGMENT +1> to display the

current setting. Enter the correct value using the number keys,

and then press <ENTER*>.

Segment Timer Operation

14

Reset Current Segment

Press <RESET CURRENT SEG> to reset the segment time to the value specied by the

current segment. The segment number will remain at the current value.

Reset to 1st Segment

Press <RESET TO 1ST SEG> to return to the rst segment. This may not necessarily be

segment “1” if the rst/last segment settings were changed.

Note: This function is disabled while the clock is running.

Warning Time

Display Action

WARNING TIME

MM:SS*

MM:SS = minutes, seconds

When the warning time is reached, the segment number ashes

until the main clock reaches zero.

Press <WARNING TIME •>, enter the time in minutes and seconds

using the number keys, and then press <ENTER*>.

Enter 00:00 for no warning time (default).

Copy Range

This key sets a range of segments to a specic value.

Display Action

COPY: MM:SS *

SEG XX TO YY

MM:SS = minutes, seconds

XX = starting segment value

YY = ending segment value

Press <COPY RANGE •> and enter the time desired. Press

<ENTER*> to move to the next eld. Enter the rst and last

segments that will have this time. When the last segment in the

copy range is set, the menu will be exited.

Once completed, all segments from XX to YY (inclusive) will be

set to the specied value.

Auto Stop

Note: To set the console to stop after the last segment in the series is completed, the

auto stop at each segment setting must be set to NO.

Display Action

STOP AT EACH SEG

1-YES 2*NO

Press <AUTO STOP> to enter this menu.

• Press <1> to set the console to stop after each segment is

completed.

• Press <2> to set the console to automatically begin the next

segment when each segment is completed.

STOP AT LAST SEG

1-YES 2*NO

If Stop at Each Segment is set to NO, the console will then

prompt for the Stop at Last Segment setting.

• Press <1> to set the console to stop when the last segment

has been completed.

• Press <2> to set the console to start over at the rst segment

when the last segment is completed.

Segment Timer Operation

15

Set Program

The segment timer mode includes 7 programs as described below. Program information

is saved when the All Sport 100 is powered down.

• Programs 1-5 allow a unique program for each weekday (Monday through Friday).

• Program 6 is a dedicated Play Clock.

• Program 7 is a dedicated Two-Minute Drill.

Display Action

CURRENT PROG N*

SELECT 1-7

N = current setting

Press <SET PROGRAM •> use the number keys to select the

desired program, and then press <ENTER*> to accept.

Once completed, all segments from XX to YY (inclusive) will be

set to the specied value.

TI-2025 & TI-2026 Segment Timers

The TI-2025 and TI-2026 portable timing displays (Figure 4)

are controllable by an All Sport 100 as well as a wireless

handheld RC-50 controller. However, before these

displays may be controlled with the RC-50, they must rst

be programmed with the All Sport 100. Connect the All

Sport 100 to the display using the provided power/signal

cable (part # 0A-1196-0095).

For more information about these displays, refer to the

TI-2025 & TI-2026 Segment Timers Display Manual (ED-

16738), available online at www.daktronics.com/manuals.

Sending Program Information to the Display

Display Action

TRANSFERING DATA

PLEASE WAIT

TRANSFER

COMPLETE

First ensure the All Sport 100 is properly connected to the TI

display, and then enter the information for programs 1 to 7.

When ready to load the program information into the display,

press <ALT> followed by <SEND>.

Wait approximately 5 seconds for the program data to transfer.

The TI display digits will show “PPPP” if the program data was

successfully received and stored into the display’s memory.

The All Sport 100 must then be unplugged to allow the RC-50 to

control the display remotely.

DAKTRONICS

Figure 4: TI-2025/TI-2026

Segment Timer Operation

16

Play Clock (Program 6)

Program 6 is a dedicated two-digit play clock. The play clock can be set up to 99

seconds using the <SET TIME •> key.

Display Action

CURRENT PROG 6*

SELECT 1-7

On the All Sport 100, press <SET PROGRAM •> followed by <6> to

set the console to the play clock Program 6. Press <ENTER*> to

accept.

SET PLAY

CLOCK 0:SS*

SS = seconds

Press the <SET TIME •> key. Enter a time using the number keys

and press enter to accept the changes.

PLAY CLOCK }

TIME: 0:25 P6

Press <START> to start the play clock.

Press <STOP> to stop AND reset the play clock.

Two-Minute Drill (Program 7)

Program 7 is a dedicated two-minute drill clock. This program consists of two different

clocks: a 2-minute game clock and a 25-second play clock. Times are not adjustable�

Display Action

CURRENT PROG 7*

SELECT 1-7

On the All Sport 100, press <SET PROGRAM •> followed by <7> to

set the console to the two-minute drill Program 7. Press <ENTER*>

to accept.

PLAY: 0:25 }

MAIN: 2:00 P7

Press <START> to start the main clock.

Press <STOP> to stop the main clock.

Press <CURRENT SEGMENT +1> to start the play clock.

Press <CURRENT SEGMENT +1> a second time to stop and reset

the play clock.

RC-50 Controls

Some buttons on the RC-50 (Figure 5) vary depending on the selected program.

Note: The All Sport 100 must be disconnected from the

display before the RC-50 will control it.

Segment Timer (Programs 1-5)

• <START> – Starts the segment timer

• <STOP> – Stops the segment timer

• <RESET PROGRAM> – Resets the current program

• <PROGRAM + > – Increments the program number

• <RESET SEGMENT> – Resets the current segment time

• <SEGMENT + > – Increments the current segment number

• <SEGMENT – > – Decrements the current segment number

• <HORN> – Manually sounds the horn Figure 5: RC-50

Daktronics ALL SPORT 100 User manual

Popular Controllers manuals by other brands