Danby DPA100EAUWDB User manual

DANBY PRODUCTS LIMITED, ONTARIO, CANADA N1H 6Z9
DANBY PRODUCTS INC., FINDLAY, OHIO, USA 45840
OWNER’S MANUAL
MANUEL DU PROPRIÉTAIRE
MANUAL DEL PROPIETARIO
PORTABLE AIR CONDITIONER
Owner’s Manual.............................1 - 12
CLIMATISEUR PORTABLE
Manuel du propriétaire.................13 - 24
AIRE ACONDICIONADO PORTÁTIL
Manual del propietario.................25 - 36
MODEL •MODÈLE •MODELO
DPA100EAUWDB
DPA100EAUBDB
DPA120EAUWDB
DPA120EAUBDB
2017.11.21

Welcome
Welcome to the Danby family. We are proud of our quality products and we believe in
dependable service. We suggest that you read this owner’s manual before plugging in your new
appliance as it contains important operation information, safety information, troubleshooting and
maintenance tips to ensure the reliability and longevity of your appliance.
Visit www.Danby.com to access self service tools, FAQs and much more. For additional assistance
call 1-800-263-2629.
Note the information below; you will need this information to obtain service under warranty.
You must provide the original purchase receipt to validate your warranty and receive service.
Model Number: _________________________________________________
Serial Number: _________________________________________________
Date of Purchase: _______________________________________________
Need Help?
Before you call for service, here are a few things you can do to help us serve you better.
Read this owner’s manual:
It contains instructions to help you use and maintain your appliance properly.
If you receive a damaged appliance:
Immediately contact the retailer or builder that sold you the appliance.
Save time and money:
Check the troubleshooting section at the end of this manual before calling. This section
will help you solve common problems that may occur.
1-800-26- Danby
(1-800-263-2629)
1

SAFETY REQUIREMENTS
This appliance is not intended for use by persons
(including children) whose physical, sensory or
mental capabilities may be different or reduced,
or who lack experience or knowledge, unless such
persons receive supervision or training to operate
the appliance by a person responsible for their
safety.
Children should be supervised to ensure that they
do not play with the appliance.
To avoid risk of electric shock, do not operate this
appliance in an area that is likely to accumulate
standing water. If this condition develops, disconnect
the power supply before stepping into the water.
Do not store or use combustible materials such as
gasoline or other flammable vapors or liquids in the
vicinity of this or any other appliance.
Do not insert fingers or other objects into grills or
openings in the appliance.
Do not cover or block the intake and exhaust
openings.
Do not operate the appliance without the filter
installed.
Do not operate the appliance near heat sources.
This appliance is intended for indoor, residential
applications only. Do not use this appliance
outdoors. Do not use this appliance for commercial
or industrial applications.
If the air conditioner is transported on its back or
side, it must be allowed to stand upright for 6 hours
before plugging in to avoid damage to internal
components.
Keep the appliance away from walls, furniture and
curtains with a clearance of at least 30 cm (12
inches) on all sides.
GROUNDING INSTRUCTIONS
This appliance must be grounded. Grounding
reduces the risk of electrical shock by providing an
escape wire for the electrical current.
This appliance has a cord that has a grounding
wire with a 3-prong plug. The power cord must be
plugged into an outlet that is properly grounded.
If the outlet is a 2-prong wall outlet, it must be
replaced with a properly grounded 3-prong wall
outlet. The serial rating plate indicates the voltage
and frequency the appliance is designed for.
WARNING - Improper use of the grounding
plug can result in a risk of electric shock.
Consult a qualified electrician or service agent
if the grounding instructions are not completely
understood, or if doubt exists as to whether the
appliance is properly grounded.
Do not connect the appliance to extension cords,
adapters or together with another appliance in the
same wall outlet.
Do not splice the power cord. Do not under any
circumstances cut or remove the third ground prong
from the power cord.
If the power supply cord is damaged, it must be
replaced by the manufacturer, its service agent or
similar qualified person in order to avoid hazard.
Important Safety Information
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS!
2

INSTALLATION INSTRUCTIONS
3
ASSEMBLING THE WINDOW KIT
1. Attach the air outlet adapter and the window
slider adapter onto either end of the exhaust
hose.
2. Insert the air outlet adapter into the lower
groove of the air outlet on the back of the
appliance. Ensure that the hook of the adapter
is aligned with the hole seat of the air outlet and
then slide down
3. Measure the window opening where the window
kit will be installed. Assemble as many sliders as
necessary to fit the window.
4. If the length of the window requires all three
sliders, use two bolts to fasten the sliders at the
correct length.
5. If the window opening is less than the minimum
length of a single slider, use the slider that has
the hole in it and cut it to the correct length.
Make sure not to cut the end that has the hole
as this is necessary to attach the exhaust hose
adapter.
2
3
1
REQUIRED TOOLS
1. Medium sized Phillips screwdriver
2. Tape measure or ruler
3. Knife or scissors
4. Saw (in the event that the window sliders need to
be cut to size)
ACCESSORIES
1. Air outlet adapter
2. Exhaust hose
3. Window slider adapter
4. Bolts
5. Window slider A
6. Window slider B and C
7. Caster locks
8. Foam seal A (adhesive)
9. Foam seal B (adhesive)
10.Foam seal C (non-adhesive)
11.Security bracket and 2 screws
12.Drain hose
13.Remote control
1
2
3
4
5
6
7
8
9
10
11
12
13

INSTALLATION INSTRUCTIONS
4
INSTALLING THE WINDOW KIT
There are two possible installation methods
depending on the available window type.
Hung Window Installation
1. Cut the adhesive foam seals A and B to the
correct length for the window. Attach them to the
window sash and frame as shown.
2. Insert the assembled window slider kit into the
window opening.
3. Cut the non-adhesive foal seal C to match
the width of the window. Insert the foam seal
between the glass and the window frame to
prevent air and insects from getting into the
room.
4. Install the security bracket in the window frame
with the two provided screws.
5. Attach the window slider adapter to the hole in
the window slider kit.
A
B
AB
1
2
3
4
5
Note: Do not over extend or bend the hose as this
will impede air flow.

5
INSTALLATION INSTRUCTIONS
Sliding Window Installation
1. Cut the adhesive foam seals A and B to the
correct length for the window. Attach them to the
window sash and frame as shown.
2. Insert the assembled window slider kit into the
window opening.
3. Cut the non-adhesive foal seal C to match
the width of the window. Insert the foam seal
between the glass and the window frame to
prevent air and insects from getting into the
room.
4. Install the security bracket in the window frame
with the two provided screws.
5. Attach the window slider adapter to the hole in
the window slider kit.
B
B
A
A
1
2
3
4
5
Note: Do not over extend or bend the hose as this
will impede air flow.

OPERATING INSTRUCTIONS
FEATURES
Front
1. Control panel
2. Air outlet grill
3. LED display
4. Handle (both sides)
5. Air intake grill
6. Rollers
Rear
1. Air intake grill
2. Air outlet
3. Drain outlet
4. Power cord
LOCATION
Place the air conditioner on a smooth, level floor
that is strong enough to support it and all included
accessories.
Make sure the appliance is level to minimize noise
and vibration.
The appliance must be installed near a grounded
receptacle and the overflow drain outlet on the rear
of the appliance must be accessible.
Do not cover air inlets or outlets or the remote
control receiver on the control panel.
The appliance requires 30 cm (12 inches) of
clearance on the front and sides.
The appliance requires at least 50 cm (20 inches) of
clearance on the back.
6
1
2
3
4
5
6
1
2
3
4

OPERATING INSTRUCTIONS
CONTROL PANEL
1. Fan Button: Press to select fan speed; low,
medium, high.
2. Mode Button: Press to select the desired mode.
Modes will cycle in sequence with each press of
the button; cool, dry, fan.
3. Power Button: Press to turn the appliance on or
off.
4. Up and Down Buttons:
• Used to adjust the set temperature in 1°
increments.
• Press and hold both up and down buttons for 3
seconds to change the temperature display from
°C to °F.
7
12
3
4
13
2
45
LED DISPLAY
1. Temperature and Timer Display: Shows the set
temperature of the timer setting.
2. Temperature Scale: Indicates whether the
temperature scale is set to °C or °F.
3. Timer Indicator: Illuminates if the timer is
activated.
4. Fan Speed Display: Shows the current fan speed
setting; low, med, high.
5. Mode Display: Shows the current mode; cool,
dry, fan.
REMOTE CONTROL
1. Fan Button: Press to select fan speed; low,
medium, high.
2. Swing Button: Press to start the auto swing
feature. When auto swing is activated, press
again to stop the louver at the desired angle.
3. Sleep: Press to start the sleep function.
4. Up and Down Buttons: Used to set the
temperature and timer.
5. Power Button: Press to turn the appliance on or
off.
6. Mode Button: Press to select the desired mode.
Modes will cycle in sequence with each press of
the button; cool, dry, fan.
7. Timer Button: Press to set the timer function.
8. °C/°F Button: Press to change the temperature
display from °C to °F.
1
2
3
4
5
6
7
8

Operating Modes
• Cool Mode
Choose cool mode to set the cooling function. Use
the up and down Arrows to choose the desired
temperature. Press the fan button to adjust the fan
speed.
The temperature can be set within a range of 18 -
32°C (64 - 90°F).
The exhaust hose should be installed during cool
mode to ensure the best results.
• Dry Mode
Choose dry mode to remove excess moisture from
the air during periods of high humidity. All water
pulled from the air will collect inside the appliance
and evaporate due to the heat from the compressor.
In especially humid conditions, it may be necessary
to empty the drain pan when it becomes full. Press
the fan button to adjust the fan speed.
The exhaust hose should be installed during dry
mode to ensure the best results.
• Fan Mode
Choose fan mode to run the internal fan without
engaging the cooling function. Press the fan button
repeatedly to choose the fan speed, low, med, high.
OPERATING INSTRUCTIONS
Timer Function
To set the turn off timer:
• Ensure the appliance is turned on.
• Press the timer button, the time on the display
will flash.
• Press the timer button to select the desired
amount of hours before the unit turns off.
To set the turn on timer:
• Ensure the appliance is turned off.
• Press the timer button, the time on the display
will flash.
• Press the timer button to select the desired
amount of hours before the unit turns on.
Notes:
• The display will revert back to showing the
temperature setting if the appliance does not
receive a signal within a 5 second period during
programming.
• Turning the appliance on or off at any time
or adjusting the timer setting to 0.0 hours will
cancel the timer settings.
• The timer can be set between 1 - 24 hours.
Sleep Function
The Sleep Function can be used to conserve energy
during sleeping hours.
When selected, the set temperature will increase
by 2 degrees over a 2 hours period. The appliance
will hold the new set temperature for 7 hours before
automatically returning to normal operation.
The Sleep Function can be canceled at any time by
pressing the Sleep Button.
8

OPERATING INSTRUCTIONS
REPLACING THE REMOTE BATTERIES
The remote control will arrive with a CR2025 coin
battery pre-installed. It may be necessary to remove
a clear, plastic insulating strip before first use of the
remote control.
Follow the steps below to replace the battery.
1. Use a screwdriver to remove the screw that
secures the battery cover.
2. Push the battery cover hook to the right to
release it from the remote control. Pull the
battery cover out.
9
IMPORTANT
Do not dispose of
batteries as unsorted
municipal waste. Refer
to local laws for proper
disposal of batteries.
Notes:
• The air conditioner will not respond if curtains,
doors or other materials block the signal from
the remote control to the appliance.
• If the infrared signal receiver on the indoor unit
is exposed to direct sunlight, the air conditioner
may not function properly. Use curtains to
prevent the sunlight from falling on the receiver.
• Do not allow the remote control to get wet.
• Do not expose the remote control to direct
sunlight or heat.
• Do not leave the battery in the remote control
if it is not going to be used for more than 2
months.
1
2
WATER DRAINAGE
When the internal drain pan becomes full the
appliance will beep 8 times and the digital display
will show error code P1. The air conditioning or
dehumidifying action will stop but the fan may
continue to operate.
Follow the steps below to drain the appliance.
1. Turn the appliance off and unplug it from the
power source.
2. Carefully move the appliance to a location
where the water can be drained.
3. Remove the drain plug and allow the water to
completely drain.
4. Replace the bottom drain plug, pressing firmly to
ensure a tight fit and no leaks.
5. The P1 error symbol will disappear and the
appliance will resume regular function once
power is restored.