Dancing Wings Hobby GEEBEE User manual


R01

Balsawood Airplane
工具
Tools Needed
飞行参数
Specification
翼展:600mm
机长:550mm
起飞重量≈210g
Wingspan: 600mm
Length: 550mm
Flying Weight≈210g
推荐配置
Suggested Equipment
推荐马达: MM1904-1908 1500-2000KV
推荐电调: 20A
推荐舵机: 5g*3pcs
推荐桨叶: 7-8寸
推荐电池 2S 400-800mAh
推荐4通道以上接收机
Suggested Motor: MM1904-1908 1500-2000KV
Suggested ESC: 20A
Suggested Servos: 5g*3pcs
Suggested Propeller: 7-8 inch
Suggested Battery: 2s 400-800mAh
Radio≥4CH
● 这个产品不是玩具，而是一个复杂的具有难度的飞行器。您和您身边人的安全取决于您如何操作它，您需要了解相关知识，并谨慎操作。禁止
没有成人陪伴的儿童独自操作该设备。不适合14岁以下人群使用。再次强调，这不是一个玩具。
● This product should not be considered a toy, but rather a complicated and sophisticated flying model. Your safety depends
on how you use and fly it, If not correctly operated, could cause injury to you or your family members. Children must be
accompanied by an adult at all times if operating this product. Not suitable for children under the age of 14. THIS IS NOT A
TOY.
● 不要在机场，军事基地，居民区或其他任何受限制的地方飞行。
● Do not fly around some restricted location like airports, military bases, residential areas, etc.
● 您需要对发射机进行距离检查，以确保没有收到任何干扰。
● You will need to range check the transmitter to be sure you are not experiencing any interference.
● 始终保持先打开发射机后打开接收机，先关闭接收机后关闭发射机的步骤。
● Always turn on the receiver last after turning on the transmitter and shut off the receiver first before turning off the transmitter.
● 如果您是初学者，建议您在有经验玩家的协助下调试和飞行。
● If you are only a beginner to the radio control model flying, do not attempt to fly your model without any assistance or advice from
advanced expert fliers.
● 请将相关物品放置在孩子们够不到的地方
● Keep relevant items out of reach of children.
● 这个设备的设计已经超过我们正常使用所需要刚性要求，但若您需要以超出我们推荐的动力飞行时，请合理控制动作幅度并适当增加机体强度。
● This product has been flight tested to meet or exceed our rigid performance and reliability standards in normal use,if you plan to perform
any high-stress flying, you are solely responsible for taking any and all necessary steps to control movement range and reinforce the body
strength.
● 您的设备中可能包括一些玻纤和碳纤雕刻的部件，这些纤维部件所带的粉尘可能会引起眼睛，皮肤的不适，请您在需要的时候带上护目镜或者防尘服。
● This product may include some fiberglass and carbon-fiber reinforced plastic parts,which may cause eye and skin discomfort,pls wear the
goggles or dust-proof clothes when needed.
● 因航空运输安全管制，您收到的产品可能没有清单中出现过的胶水，请您理解无法发送胶水给您的原因。您可以在当地文具店很方便的购买到您所需要
的胶水。
● Due to air traffic safety control, the products you receive may not have the glue that appears in the list. Please understand and purchase the
glue you need at your local stationery store.
注意事项
SAFETY PRECAUTIONS
http://www.dwhobby.com/

02 机身组装Assemble the Fuselage
03 各部件完成 打磨
Finish the assembly and Polishing
01-10 01-11
02-1
B6
B4
B4
B4
B4
B4
B4
B4
B4
B8
B8
B5
A
机翼反面
Back side of the wing Front side of the Wing
机翼正面
4*5mm轻木条
4*5mmbalsawood strip 02-2
02-3
F
CUT
切开
完成各部件后，用砂纸打磨平滑，然
后进行蒙皮操作，蒙皮完成后进行下
一步安装。
After completing the parts, polish
them with sandpaper, then make
a covering film, and then finish
the next step after the film is
finished.
机翼组装 Assemble the Wing 01
01-1 01-2
01-3
01-4
01-5
01-6 01-7
01-8
01-9
B1
B2
B2
B2
B2
B3
C4
B3
C1
B3
B3
B7
C3
C4
C4
注意：木件用美工刀从板材上取下，各连接点用快干胶定型，用白乳胶固定。
Note:Take down the parts from the board by knife.pls use the fast dry adhesive as
stablization to connect all joints and white latex as reinforcement.
注意：机翼拼装时在平整工作台进
行，并保持机翼平直。
Note:Pls assemble the wing on
a flat table.and keeps the wing
horizontal. 4*5mm轻木条
4*5mm balsawood strip
5*5mm轻木条
5*5mm balsawood strip
4*5mm轻木条
4*5mm balsawood strip
按实际长度截取
Pls cut the balsawood strips according to
the actual length.
切除
CUT
先粘贴一边，然后弯曲B7 粘贴另一边
Paste one side first, then bend B7
and paste the other side
注意：把C3粘贴在机翼的中心线上，
粘贴C4加固。
Glue the C3 in the middle line of
the wing and glue the C4 as
reinforcement.
注意：粘贴B7蒙板时，请用少量水湿润蒙板，方便弯曲。
Note:Moisten the covering board B7 with a little
water for easy bending.
注意：粘贴B7蒙板时，涂完胶水后，可以用橡皮筋固定住，待胶水干后取下。
Note: When pasting the B7 mask, after applying the glue, it can be fixed
with rubber band. After the glue is dry, you remove it and paste again.
1

04 安装电机，舵机 Install the motor and servos
06 安装桨叶 Install the propeller
桨叶通过桨保护器固定到电机上。
Fix the propeller onto the
motor by prop saver.
Aileron
通常情况下，舵面角度的设置如下：
Usually, the control throws set as below:
≈50mm
Elevator
15°
15°-30°
15°-30°
15°
升降舵
副翼
Rudder
15°
15°
方向舵
常规飞行(Normal Flying) 3D飞行 部分飞机支持(3D Flying only support some models)
副翼 Aileron ±（15°-30°） ±40° 或者更大(or larger)
平尾 Elevator ±15° ±40° 或者更大(or larger)
垂尾 Rudder ±15° ±40° 或者更大(or larger)
常用襟翼 Flap （起飞 take-off）15°-20° （降落 Landing）20°-40°
部分特殊机型会有V型尾翼，襟翼，前缘机翼或舵面很小等，可以以常规飞行的角度作为参考，在您不确认且没有有经验人员指导的情况下，我们
建议您先以小角度试飞以确认您的设置是否正确。
Some special models will have V-tails, flaps, leading edge wings, etc., which can be used as a reference for conventional flight angles.
If you do not confirm and there is no experienced person to guide you, we recommend that you first test at a small angle to confirm
that your settings are correct.
07 安装舵角，连杆 Install the servo horns and linkage rods.
07-1
07-2
07-3
快装接头
EZ Connector
快装接头
EZ Connector
快装接头
EZ Connector
舵角
servo horn
舵角
servo horn
舵角
servo horn
05 安装机翼，尾翼 Assemble the wing and tail wing.
纸合页
Papar hinge
05-2
05-3
05-1
在方向舵升降舵上用美工刀切开小口，插入纸合页。
Cut off a small opening on rudder and elevator,and insert the paper hinges.
05-4
机翼插入机身，调整与机身
垂直后，连接处用胶水粘合
固定。
The wing is instered into
the fuselage ,make it
vertical with fuselage,then
fix the joints by glue.
05-5
安装副翼，用纸合页连接，安装方法与步骤05-2相同。
Install the ailerons and connect them with paper
hinges,the installation way is same as the step 05-2.
纸合页
Papar hinge
2
机翼中部
Middle part of the Wing
机身中部
Middle part of the fuselage

≈50mm
C.G
08 调整重心 Adjust the C.G.
Control Directions Tests
Elevator
升降舵
方向舵
副翼
AileronRudder
遥控器动作 飞机反应
升降杆下拉
Direction rod to the left
升降杆上推
Direction rod to the right
Steering rod to the left
Steering rod to the right
Lifting rod up
Lifting rod down
转向杆向右
转向杆向左
方向杆向右
方向杆向左
地面控制方向测试
● 安装舵机前，请先将舵机通电让舵机中心点回中，以便能更好的调试舵面。
● Check/adjust servo centering, in order to adjust the control surface better.
● 初次启动电机，您需要确认电机旋转的方向以适配您的机型。
● Double-check the spinning direction of motor at first usage, and sure it’s suitable for your model.
● 请将重心（CG）调整至说明书所述位置并尽量靠近。如果有需要，您可以增加机头或者机尾的重量，以确保机体有更
好的飞行姿态。
● Set the center of gravity (CG) at the position that manual already marked out. If necessary, add weight to
the nose or tail to ensure the best flight performance.
● 检查机身内部，确保所有设备正常连接；检查机身表面，包括但是不限于蒙皮，固定螺丝，舱盖，座舱罩等位置。
● Double-check the inside of the fuselage, make sure all the equipments are correctly connected; Check the
heat-shrink covering material’s surface, Make certain all screws, bolts, cabin and canopy remain secure.
● 在飞行前，请检查您电池情况，若有低电压，电池损坏等情况，请您停止操作并马上更换电池。
● Take great care when connecting/disconnecting the battery, pls replace the battery immediately once found
low voltage or damage to battery.
● 机身内部设备连接的方式，会和您的收发设备有关，在一些功能更多的收发设备上，您可以通过设置简化机身内部设
备的连接。详细请查看您的收发设备以确认是否满足您需要的功能。
● The way the internal devices of the fuselage are connected will be related to your transmitter-receiver
device. For those transmitter-receiver devices with more functions, you can simplify the connection of the
internal devices of the fuselage. Check your device for details to see if it meets the features you need.
● 动力设备和收发设备第一次配对时，可能需要设置油门最大行程，请您自行设置。
● When the power system and transmitter-receiver device are paired for the first time, you may need to set
the maximum stroke of the throttle. Please set it yourself.
飞行前的建议
PRE-FLIGHT CHECKS
3