Dancing Wings Hobby T90 Tractors User manual

 
T90

Balsawood Airplane
工具
Tools Needed
飞行参数
Specification
翼展:2130mm
机长:1500mm
起飞重量≈5.3Kg
Wingspan: 2130mm
Length: 1500mm
Flying Weight≈5.3Kg
推荐配置
Suggested Equipment
推荐引擎: DLE 20cc/DLE 20ccRA
推荐舵机: 37g*7pcs
推荐桨叶: 16-18寸
推荐8通道以上接收机
Suggested Motor: DLE 20cc/DLE 20ccRA
Suggested Servos: 37g*7pcs
Suggested Propeller: 16-18 inch
Radio≥8CH
● 这个产品不是玩具，而是一个复杂的具有难度的飞行器。您和您身边人的安全取决于您如何操作它，您需要了解相关知识，并谨慎操作。禁止
没有成人陪伴的儿童独自操作该设备。不适合14岁以下人群使用。再次强调，这不是一个玩具。
● This product should not be considered a toy, but rather a complicated and sophisticated flying model. Your safety depends
on how you use and fly it, If not correctly operated, could cause injury to you or your family members. Children must be
accompanied by an adult at all times if operating this product. Not suitable for children under the age of 14. THIS IS NOT A
TOY.
● 不要在机场，军事基地，居民区或其他任何受限制的地方飞行。
● Do not fly around some restricted location like airports, military bases, residential areas, etc.
● 您需要对发射机进行距离检查，以确保没有收到任何干扰。
● You will need to range check the transmitter to be sure you are not experiencing any interference.
● 始终保持先打开发射机后打开接收机，先关闭接收机后关闭发射机的步骤。
● Always turn on the receiver last after turning on the transmitter and shut off the receiver first before turning off the transmitter.
● 如果您是初学者，建议您在有经验玩家的协助下调试和飞行。
● If you are only a beginner to the radio control model flying, do not attempt to fly your model without any assistance or advice from
advanced expert fliers.
● 请将相关物品放置在孩子们够不到的地方
● Keep relevant items out of reach of children.
● 这个设备的设计已经超过我们正常使用所需要刚性要求，但若您需要以超出我们推荐的动力飞行时，请合理控制动作幅度并适当增加机体强度。
● This product has been flight tested to meet or exceed our rigid performance and reliability standards in normal use,if you plan to perform
any high-stress flying, you are solely responsible for taking any and all necessary steps to control movement range and reinforce the body
strength.
● 您的设备中可能包括一些玻纤和碳纤雕刻的部件，这些纤维部件所带的粉尘可能会引起眼睛，皮肤的不适，请您在需要的时候带上护目镜或者防尘服。
● This product may include some fiberglass and carbon-fiber reinforced plastic parts,which may cause eye and skin discomfort,pls wear the
goggles or dust-proof clothes when needed.
● 因航空运输安全管制，您收到的产品可能没有清单中出现过的胶水，请您理解无法发送胶水给您的原因。您可以在当地文具店很方便的购买到您所需要
的胶水。
● Due to air traffic safety control, the products you receive may not have the glue that appears in the list. Please understand and purchase the
glue you need at your local stationery store.
注意事项
SAFETY PRECAUTIONS
http://www.dwhobby.com/

1
KIT
组装说明 How to Assemble
机身拼装 Assemble the Fuselage
拼装之前 请打磨雕刻连接处的地方。
Pls polish the joints before assembly.
注意：木件用美工刀从板材上取下，各连接点用快干胶定型，用白
乳胶固定。
Note:Take down the parts from the board by knife.pls use the
fast dry adhesive as stablization to connect all joints and
white latex as reinforcement.
01-1
配件图仅做参考用，您收到的实物可能因为
修改/优化的原因导致与图片有略有不同。
Photos shown here just for reference,
the product you received maybe
slightly differ from the photos due to
continuous improvement on products.
01-2
01-3
01-4
细节Detail 1
C1
C4
C2
F2
F1*2
F3
F22
F28*2
F4
C1-1
01-6 01-7
01-5
在平整工作台上粘合C1，C1-1
Pasting C1 and C1-1 on a flat
workbench 对齐 Align
对齐 Align
F26 F26 F26 F26-1 F26-1
F22-1*2 F22-2*2
F26
01-3
01-4
F21 F5
F7
F6
F9
F8
F23
F17
F24
ERS
F10F11
F12
01-8 01-9
01-10
01-11
01-12
01-13
01-14
01-15 01-16
01-17
01-18
在卡口内嵌入轻木条 6*8mm
Insert the balsa strip into the slot
在卡口内嵌入轻木条 6*8mm
Insert the balsa strip into the slot
在卡口内嵌入轻木条 6*8mm
Insert the balsa strip into the slot
在卡口内嵌入轻木条 6*8mm
Insert the balsa strip into the slot
F29-1
F29
F29-3
F29-4
按01-1.01-2步骤拼好另一侧板，注意左右方向。然后拼装到
机身，并注意安装步骤01-9.01-10的轻木条。
Assemble the other side of the board according to the
steps 01-1.01-2, pay attention to the left and right
direction. Then assemble to the fuselage, and pay
attention to the installation of the balsa strip of step
01-9.01-10
注意：拼装完成后检查机身对称性，调整
保持机身不要扭曲。然后进行后续步骤。
Note: Check the symmetry of the
fuselage after the assembly is
completed, and adjust to keep the
fuselage body from twisting.Then
proceed to the next steps.
M4爪牙螺母
M4 claw nut M3爪牙螺母
M3 claw nut
注意爪牙螺母朝向
Pay attention to the claw nut orientation
注意爪牙螺母朝向
Pay attention to the claw nut orientation
拼装此步骤时，用少量快干胶稍加固
定，方便后面步骤调整。
When assembling this step, use a
small amount of quick-drying
glue to fix it slightly, which is
convenient for later adjustment.
此处需两段轻木条拼接
Here you need to
paste together the two
pieces of balsa strips
01-2
F23-1
此处需两段轻木条拼接
Here you need to
paste together the two
pieces of balsa strips
轻木条 6*8mm
balsa strip 6*8mm
轻木条 4*5mm
balsa strip 4*5mm
轻木条 4*5mm
balsa strip 4*5mm
轻木条 4*5mm
balsa strip 4*5mm
按实际长度截取
Cut according to actual length
按实际长度截取
Cut according to actual length
按实际长度截取
Cut according to actual length
按实际长度截取
Cut according to actual length
按实际长度截取
Cut according to actual length
按实际长度截取
Cut according to actual length
按实际长度截取
Cut according to actual length
按实际长度截取
Cut according to actual length

机翼拼装 Assemble the Wing
2
01-19 01-20 01-21 01-22
01-23
01-2401-24
01-25
此处轻木F29-2
粘固后进行打
磨，与机身弧度
成为整体。
Paste and
polish the
balsa wood
F29-2 here
until it is
integrated
with the
curvature of
the fuselage.
D1
F19
F13
F14
F15
F19-1
D2
机翼拼装请参考机翼1：1图纸，拼装时在平整工作台上进行。此处标注了一部分拼装细节，请结合图纸进行拼装。
Pls assemble the wing as per the supplied 1:1 drawing, which is carried out on the flat workbench during
assembly. Here we marked out some assembly details,please assemble them in combination with the
drawings.
嵌入加强条
insert the reinforcement strips
M1-1
M1-1
M1
M1
F29-2*3
F29-2*3
M1-2
M1-2
M1-3
M1-4
M1-4M1-3
在上图位置安装此贴，并确保仓身盖
磁铁与机身上磁铁为相吸状态。
Install the magnet in the position
above and make sure that the
magnet of the body cover is in
the same state as the magnet on
the body.
蒙板先在平面上拼装，粘合成上图状态，再蒙到机翼上。上图为上蒙板，下蒙
板为编号DM1-DM5，参考上蒙板拼装。
Firstly assemble the cover mask on the flat workbench,bonded to the
state of the above picture, and then paste to the wing. The picture
above shows the upper mask, the lower mask is numbered
DM1-DM5,which need to assemble in same way as upper mask.
01-26
01-27
仓身盖为磁吸设计，可开合。
The body cover is designed for magnetic attraction and
can be opened and closed.
完成机身拼装后，需整体打磨平滑，待下一步进行蒙皮。
After the fuselage is assembled, it needs to be polished
and smoothed, and waiting for covering the film.
细节Detail 4
细节Detail 3
细节Detail 6
细节Detail 7
细节Detail 5
细节Detail ２
DP-1DP
细节Detail 1
在机翼前端粘贴L1-1,并打磨成机翼一体弧度。
Paste L1-1 on the leading edge od the wing
and sand it into a full arc of the wing.
UM1
UM1-1
UM5 UM3
UM4
UM2
副翼拼装时注意垫入轻木块，并
打磨斜面，然后再粘贴AUM
When assembling the aileron,
you need to put balsawood
block and polish the bevel,
then paste the AUM.
背面打磨平滑
The back needs to be
polished and smoothed
AUM
在预留槽内装入合页，快干胶粘固。
Insert the hinge in the reserved
slot,and fix them with fast-drying
adhesive.
襟翼拼装时注意垫入轻木块，并打磨斜面，然
后再粘贴FUM
When assembling the flaps, you need to
put the balsawood block, polish the bevel,
and then paste the FUM.
细节Detail 8
1
1
2
2
2
先插入长玻纤片1，然后再侧
边卡入方玻纤片2，卡牢固后
用胶水粘合2在机翼上。
Firstly insert the long
fiberglass sheet 1,
secondly insert the square
fiberglass sheet 2 on the
side,finally fix them firmly
to the wing with glue.
嵌入加强条 insert the reinforcement strips
注意：保持平整无变形，完成后需打磨。
Note: Keep it flat and free of deformation,
and polish it when finished.
蒙皮详细操作可查看以下链接内容，我们提供了蒙
皮范本（可直接扫二维码）
http://www.dwhobby.com/art/film
M1蒙板有长短两种，具体见页码4结尾处描述。
M1 masks are available in both long and short
versions. See page 4 for details.
For detailed operation of the film, please view
the following link.We provide the example (can
directly scan the QR code)
铝管 20*530MM
Aluminum tube 20*530MM

3
蒙皮详细操作可查看以下链接内容，我们提供了蒙皮范本
（可直接扫二维码）
http://www.dwhobby.com/art/film
机翼背面
Back side of the wing
细节Detail 9 细节Detail 10
副翼安装到机翼，合页插入机翼预留槽内，用快干胶粘固，并保持副
翼可以上下摆动。
The aileron is mounted to the wing, and the hinges are inserted
into the reserved slot of the wing,and fasten with quick-drying
glue,make sure the aileron can be swung up and down.
以下2个步骤建议蒙皮完成后再安装。
The following two steps recommend to install after covering the film.
后续步骤需要蒙皮处均可参考此蒙皮范本。
Follow-up steps that need to cover the film refers to this template.
蒙皮前可在机翼内放置一跟引导线，方便拉出舵机线。
A guide wire can be placed in the wing before covering the film,more
convenient to pull out the servo wire.
以下步骤需蒙皮完成后再安装。The following steps need to install after covering the film.
襟翼如上图连接到机翼，用合页加自攻螺丝固定住。
The flap is connected to the wing as shown above,and fasten
with hinges and self-tapping screws.
自攻螺丝
机翼及起落架安装到机身 Mount the wing and Landing gear to the fuselage
尾翼及后尾轮安装到机身 Mount the tail and rear tail wheel to the fuselage
电子设备及引擎安装示范 Installation for Power system and Engine
02-1 02-2
02-3 02-1至02-3展示了机翼安装到机身的步骤。
02-1 to 02-3 show the steps to mount the wing to the fuselage
02-1插入铝管到机身居中位置。
02-1 insert the aluminum tube to the center position of the fuselage
02-2把铝管插入机翼预埋铝管内，注意玻纤片嵌入的位置。
02-2 Insert the aluminum tube into the embedded aluminum tube of the wing,
pay attention to the position where the fiberglass sheet is embedded.
02-3翻转到机身底部，用螺丝锁定机翼玻纤片。
02-3 flip to the bottom of the fuselage, lock the wing fiberglass with screws
底部
Bottom
水平尾翼插入机身尾部
卡口，用胶水粘合连接
处。安装升降舵用铰链
连接。可参考机翼拼装
的细节7，9。
The horizontal tail is
inserted into the slot
at the rear end of the
fuselage, and fix with
glue at the
joints.Install the
elevator with hinges.
See the details of the
wing assembly 7,9.
03-1
打磨垂直尾翼末端，用刀切出槽，并装入铰链，用胶水
粘固。
Grind the end of the vertical tail,and cut the groove
with a knife,finally insert the hinge and fasten with
glue.
把垂直尾翼插入机身，
胶水粘固，把方向舵对
接垂直尾翼，铰链插入
开的槽内，胶水粘固。
Insert the vertical tail
into the fuselage,and
fix with glue.Dock the
rudder to the vertical
tail,insert the hinge
into the slot and
fasten with glue.
03-4
尾轮组组合状态
Tail wheel status
长度可能需要裁剪
Length may need to
be cut
轮挡
wheel stopper
轮挡
wheel stopper
轮轴
wheel axle
把尾轮组固定到机身尾部，用自
攻螺丝固定。
Fix the tail wheel to the rear
of the fuselage and fix it with
self-tapping screws
安装尾轮组时，钢丝插入转向舵内，用大量快
干胶水粘固。使尾轮可以随转向舵转动。
When the tail wheel is installed, insert the
steel wire into the steering rudder and fix
with a large amount of quick-drying glue.
Make sure the tail wheel could turn with
the steering rudder
在机身内安装舵机，并把钢丝连杆插入机身内，钢丝
套引导管，引导管用胶水固定在机身内。
Install the servos inside the fuselage, insert the
steel wire linkage rod into the fuselage, insert
the steel wire into the guide tube, and fix the
guide tube inside the fuselage with glue.
连杆钢丝Z型一头穿入舵臂固定住。
The Z-shaped end of the linkage rod is inserted
into the servo arm.
引导管
guide tube
03-2
03-3
打磨方向舵，参考垂直尾翼装好的铰链位置用刀在方向舵
上切出槽。
Grind the rudder, refer to the hinge position of the
vertical tail and cut the groove on the rudder with a
knife.
03-5
04-1 04-2
02-4 02-5
切开
Cut
M3*10mm内六角螺丝
M3*10mm inner hexagon screws
M4*20mm内六角螺丝
M4*20mm inner hexagon screws
Self-tapping screws
以下步骤需蒙皮完成后再安装。The following steps need to install after covering the film.
轮挡
wheel stopper
铝管 18*1000MM
Aluminum tube 18*1000MM
For detailed operation of the film, please view the
following link.We provide the example (can directly
scan the QR code)

更多电子设备调试细节可参考以下链接查看（可直接扫二维码）
http://www.dwhobby.com/art/connection
常规飞行(Normal Flying) 3D飞行 部分飞机支持(3D Flying only support some models)
副翼 Aileron ±（15°-30°） ±40° 或者更大(or larger)
平尾 Elevator ±15° ±40° 或者更大(or larger)
垂尾 Rudder ±15° ±40° 或者更大(or larger)
常用襟翼 Flap （起飞 take-off）15°-20° （降落 Landing）20°-40°
部分特殊机型会有V型尾翼，襟翼，前缘机翼或舵面很小等，可以以常规飞行的角度作为参考，在您不确认且没有有经验人员指导
的情况下，我们建议您先以小角度试飞以确认您的设置是否正确。
Some special models will have V-tails, flaps, leading edge wings, etc., which can be used as a reference for conventional
flight angles. If you do not confirm and there is no experienced person to guide you, we recommend that you first test
at a small angle to confirm that your settings are correct.
Elevator
Aileron
15°-30°
15°
15°
15°
15°
15°-30°
通常情况下，舵面角度的设置如下：
Usually, the control throws set as below:
≈110mm
升降舵
Flap
襟翼
副翼
Rudder
方向舵
引擎及所需相关设备此处仅做示范，实际安装请跟据您所选设备的说明进行调整及安装。
The engine and related equipment are only shown here for reference. The actual installation should be adjusted and installed according to the
instructions of the equipment you selected.
引擎头部蒙版分为长短两套，跟据您所选用的引擎选择安装。（油动引擎建议用短蒙板，电动马达建议用长蒙板）
The engine mask is available in two sets, which are selected according to the engine you choose. (The oil engine recommends short masks and
the electric motor recommends long masks)
安装机翼上的副翼，襟翼舵机
Install the servos on the aileron and flap of the wing 安装引擎
Install the engine
襟翼舵机为内装设计，用轻木块固定在S3上，舵
机线穿入机翼内。
The flap servo should be installed inside the
wing,fix the servo on the S3 with balsawood
block,and the servo wire penetrate into the
wing.
舵机固定好后，用自攻螺丝把S3固定在机翼上。
After the servo is fixed, fasten the S3 to the
wing with a self-tapping screw.
钢丝连杆Z型一头连接舵臂，然后连杆垂直机翼确定出
舵角位置，然后安装舵角。在舵角上安装快装接头，
快装接头锁定连杆。
The Z-shaped end of the linkage rod is connected
to the servo arm. Pulling the linkage rod to the
appropriate position on the aileron determines
the position of the servo horn.Here pls note the
linkage rod needs to be perpendicular to the
wing. Then install the servo horn.Install the
EZ-connector on the servo horn,then lock the
linkage rod.
副翼上舵机安装方法和襟翼上相同。安装完成
后，舵机线从上图预留孔导出。
Install the aileron servo in the same way
as flap servo.After the installation is
completed, the servo wire is exported
from the reserved hole in the above
figure.
Self-tapping screws
自攻螺丝
S3
4
04-3 04-4
04-5
04-6
04-7
连杆从机身尾部预留槽导出，根据连
杆位置确定出舵角位置，然后安装舵
角。在舵角上安装快装接头，快装接
头锁定连杆。
The linkage rod is led out from the
reserved slot at the rear of the
fuselage,servo horn position is
determined according to the
position of the linkage rod, and
then install the servo horn.Install
the EZ-connector on the servo
horn,then lock the linkage rod.
快装接头
EZ-connector
快装接头
EZ-connector
25°
35°
襟翼设置成两个档位，起飞开启一档，升空后关闭襟翼。降落时开启二档。
The flaps are set to two gears with different angles, open the first gear (recommend angle 1) for
take-off,and close the flaps after lifting. Open the second gear (recommend angle 2) when landing.
一档
Recommend angle 1
二档
Recommend angle 2
More details about power system adjustment, please refer
to below link: (You can scan QR Code directly.)
M1
M1 M1
L1-1 M1

重心位置展示 Display for C.G
注意：设置重心时，油箱放置在重心点位
置。
Note: When setting the center of
gravity, the oil tank is placed at the
center of gravity.
折叠PVC风挡到合适形状，然后粘到驾驶室前部。
Fold the PVC windshield to the suitable shape and stick
it to the cab.
Control Directions Tests
Elevator
升降舵
方向舵
副翼
AileronRudder
遥控器动作 飞机反应
升降杆下拉
Direction rod to the left
升降杆上推
Direction rod to the right
Steering rod to the left
Steering rod to the right
Lifting rod up
Lifting rod down
转向杆向右
转向杆向左
方向杆向右
方向杆向左
地面控制方向测试
● 安装舵机前，请先将舵机通电让舵机中心点回中，以便能更好的调试舵面。
● Check/adjust servo centering, in order to adjust the control surface better.
● 初次启动电机，您需要确认电机旋转的方向以适配您的机型。
● Double-check the spinning direction of motor at first usage, and sure it’s suitable for your model.
● 请将重心（CG）调整至说明书所述位置并尽量靠近。如果有需要，您可以增加机头或者机尾的重量，以确保机体有更好的飞行姿态。
● Set the center of gravity (CG) at the position that manual already marked out. If necessary, add weight to the nose or tail
to ensure the best flight performance.
● 检查机身内部，确保所有设备正常连接；检查机身表面，包括但是不限于蒙皮，固定螺丝，舱盖，座舱罩等位置。
● Double-check the inside of the fuselage, make sure all the equipments are correctly connected; Check the heat-shrink
covering material’s surface, Make certain all screws, bolts, cabin and canopy remain secure.
● 在飞行前，请检查您电池情况，若有低电压，电池损坏等情况，请您停止操作并马上更换电池。
● Take great care when connecting/disconnecting the battery, pls replace the battery immediately once found low voltage
or damage to battery.
● 机身内部设备连接的方式，会和您的收发设备有关，在一些功能更多的收发设备上，您可以通过设置简化机身内部设备的连接。详细
请查看您的收发设备以确认是否满足您需要的功能。
● The way the internal devices of the fuselage are connected will be related to your transmitter-receiver device. For those
transmitter-receiver devices with more functions, you can simplify the connection of the internal devices of the fuselage.
Check your device for details to see if it meets the features you need.
● 动力设备和收发设备第一次配对时，可能需要设置油门最大行程，请您自行设置。
● When the power system and transmitter-receiver device are paired for the first time, you may need to set the maximum
stroke of the throttle. Please set it yourself.
飞行前的建议
PRE-FLIGHT CHECKS
5
≈110mm