Dancing Wings Hobby S25 Extra330 User manual

C1
C1-1L / C1-1R
C2
Align
Align
对齐
对齐
F1x2
F2
F18
F15
F7F8F9F10
F10
F9
F11
F12
F13
F14x2
F17x2
F3
F4
F5
F16
M2
M1
M1
Z6
Z5 Z7
Z4
Z3
Z1
Z2
Z8
Z8
M2
磁铁 magnet
磁铁
magnet
机身与舱身盖两部
分磁铁为相吸状态
Fx2
U
L
R
R1
R2
R7
R10 R9
R6
R8
R5
R3
R4
R14
R12
R11
R23
R15
R19
R13
R16
R20
R17
R22 R21
R18
E12
E1
E2
E7
E11
E10
E6
E9
E5
R24
机身组装
Assemble the Fuselage
工具 Tools Needed
S25 Extra330 V.2019
Instruction Manual
散件 KIT
1
2
3
C1，C2粘贴在一起，按预留孔对齐
C1-1L粘贴时按预留孔对齐
翻转
Turn over
把侧板粘贴到步骤 拼装的骨架
上，如下图。
3
4
5
6
7
粘贴蒙版M2时，用水稍加湿润，
方便弯曲，然后进行粘贴。
When pasting the covering
mask M2, it is slightly
moistened with water, which is
easy to bend and then pasted.
粘贴蒙版M1时，用水稍加湿润，
方便弯曲，然后进行粘贴。
When pasting the covering mask M1, it
is slightly moistened with water, which is
easy to bend and then pasted.
Cut the PVC canopy cover according to
the actual shape and then paste it onto
the hatch cover.
The cover is detachable.
Do not stick to the body
with glue.
8
9
10
11 12
仓身盖为可开合设计，请勿
用胶水粘死到机身上。
安装圆木杆
install the round
wooden rods.
机翼，尾翼组装
Assemble the Wing and Tail
尾翼组装
Assemble the Tail
13
13.1
13.2
14.1
14.2
14
Assemble the Wing
机翼组装
15
16
17
W6
W7
W5
W4
W3 W2 W1-1 W1
L2
M4
L1
顶面 Top
E8
E4
E3
E19
E13
E15E14
E22
E21
E17
E18
E20
E16
E23
按实际形状裁剪PVC座舱罩，然
后粘贴到舱盖上。
仓身内舵机位置
3X4mm桐木 Paulownia
3X3mm轻木
Balsawood
此处按实际长度截取
Paste together the C1 and C2,and
align with reserved holes
Align with the reserved holes
when paste the C1-1L
翻转
Turn over
Paste the side panel onto the
skeleton of step as shown
below
3
Cut here by actual length
servo position
inside the cabin
The two parts of the
fuselage and the body
cover are in a state of
attraction.
3X3mm轻木
Balsawood
此处按实际长度截取
Cut here by actual length

W2-1 W3-1
M5
M3
M5
L3
L4
S1
L5
L6
L3
L3
底面 Bottom
底面 Bottom
机翼前缘
Leading edge of the wing
机翼前缘按机翼弧
度打磨成弧形
垫入M3以方便副
翼舵角安装
18 19
20
21
22 23
24
25
M3
12.1
13.1 水平尾翼和垂直尾翼在机身尾部
调整好后，用胶水粘合固定。
副翼拼装好后，如图打磨成斜角
在尾翼上安装副翼，通过纸合页连接。
安装好后使副翼可以自由摆动。
调整好头罩位置后，用
自攻螺丝固定头罩到机
身上。
After adjusting the
position of the cowling,
fix the cowling to the
body with self-tapping
screws.
26
27
12.2
13.2
13.2
28
Components Assembly
各部件组装
尾翼组装
Tail Assembly
Ø7*400mm 碳管 carbon tube
机翼对插入机身后，链接
处用胶水粘合固定住。
After the wing pair is
inserted into the fuselage,
the link is glued and fixed.
29
30
31
机翼组装
Wing Assembly
起落架组装
Landing Gear Installation
后尾轮组装 Rear Wheel Installation
头罩组装
Cowling Installation
起飞重心设置
C.G. Setting
自攻螺丝
Self-tapping screws
Self-tapping screws
自攻螺丝
自攻螺丝
32
33
34
机翼舵机位置
servo position
of the wing C.G
Suggested Equipment
Motor: 2212-2216 900-1200KV
ESC: 20-30A
Propeller: 9-11 inch
Servos: 9g*4
Battery: 3s 1500-2200mAh
Radio≥4CH
Speci�ication
Wingspan: 1000mm
Length: 900mm
Flying Weight≈800g
推荐配置
马达: 2212-2216 900-1200KV
电调: 20-30A
桨叶: 9-11寸
舵机: 9g*4
电池: 3s 1500-2200mAh
通道≥4CH
参数
翼展: 1000mm
机长: 900mm
起飞重量≈800g
≈68mm
调整好重心后即可进行试飞
After adjusting the center of gravity, you can test flight.
Ø3*200mm碳管 carbon tube
自攻螺丝
The leading edge of the wing
is polished to an arc according
to the curvature of the wing.
Pad into M3 to intall
the aileron servo horn.
After the ailerons are assembled,polished
as shown in the figure.
After the horizontal tail and the
vertical tail are adjusted at the rear of
the fuselage,they are glued and fixed.
Install ailerons on the tail wing and
connect them through paper hinges.
Installed so that the aileron can swing
freely.
Self-tapping screws
Self-tapping screws
A6 A5 A1A2
A8
A7
L4
A3
A4