Dancing Wings Hobby S20 1.2M Fokker-E User manual

F11
F11
F23
F22
F20
F1
F2-1 F2-1F2
F20
F21
F24
F23
玻纤
Fiberglass
F11
F23 爪牙螺母
Nut screws +F2-2
F32-1
F32-1
F32
F32
F35
F32-2
F33-1
F35-1
F35-1 F33
F34-1 F34
F32
F3
F19
F4 F5 F6 F7 F8 F9 F10
F18
F6-1
F5-1
F17
F6-1
F5-1
F7-1
F14
F10 F18-2
F18-1
F15
F16
F7-1
F16-1
有孔一端在外
hole side out
F26
轻木条8x8x57mm
F30
F27
F28
F25
轻木条
Balsawood strip
F31
F29
F0
4x4x100mm
顶面 Top surface
底面 Bottom surface
F17
方碳杆
Square carbon rod
4x4x500mm
1.21.1 1.3
2
3
4
5
6
把步骤3中拼好的两片侧板粘合到1.3上
Stick the 2pcs sideboards which you
assembled in step 3 on the "1.3".
7.1
7.2
8.1
8.2
8.3
9
10
11 F10-1
机身组装 Fuselage Installation
机翼及尾翼组装 Wing and Tail Wing Installation
机翼及尾翼请按1：1图纸拼装，并在水平工作台面上进行拼装，
并保持拼装机翼的平整。
12
U7机翼固定插销
U7 wing fixed bolt.
堆叠粘贴后，打磨成机翼相应弧度
碳管 Carbon tube
W19
U7
W19-1
W13
W14
W15
W16
W17
W25
W25
W16-1
W16-1
S20 1.2M Fokker-E Instruction Manual
W40
W41
W42
参数
翼展：1200mm
机长：950mm
起飞重量：≈1100g
推荐配置
推荐马达：2216 920KV
推荐电调：20A
推荐电池：3S 2200-2800mAh
推荐舵机：9g*4pcs
推荐桨叶：8-9寸
通道≥4CH
Speci�ication
Wingspan: 1200mm
Length: 950mm
Flying Weight:≈1100g
Tools Needed
Electric power: 2216 920kv
ESC: 20A
Battery: 3S 2200-2800mAh
Servo：9g*4pcs
Propeller: 8-9inch
Radio≥4CH
Balsawood strip
轻木条
Balsawood strip
10x10x20mm
Install wing and tail wing according to 1:1
drawing,assemble them on the horizontal workdesk,
keep the wings straightness.
10x93mm
碳管 Carbon tube
10x93mm
Pile and stick, then sand it to the
corresponding radian of the wing.
纸合页
Paper Hinge
1

后尾轮安装图示 Rear tail wheel installation 后滑撬安装图示 Rear skid installation
起落架及机轮安装图示
Landing Gear and Wheels Installation
后起落架设计为尾轮和滑撬两种方式，分为图17,18两种安装方式，请自行选择安装
14
各完成部件组装 Finished Parts Installation
M4
M5
M3
M1
M2
U2 M0
13
安装尾翼到机身 Install tail wing to fuselage.
15 16
17 18
正面
Front
合页
L-1
玻纤L-1
Fiberglass
玻纤L-1
Fiberglass
螺丝+螺帽
背面
Back
小弹簧
Small Spring
螺丝+螺帽
螺丝+螺帽
19 19.1
19.1
19.2
19.2
自攻螺丝
Self-tapping screw
19.3
19.4
方碳管
Square carbon tube
5x5x150mm
F2-2
小弹簧
拉线支架 Bracing wire bracket
机翼安装图示
Wing Installation
马达座安装图示
Motor Board Installation
马达及桨叶安装图示
Motor and Propeller Installation
像真引擎安装图示
Scale Engine Installation
像真机枪安装图示
Scale Machine Gun Installation
按拼装步骤图在起落架配件包中，找出相应形状的钢
丝、碳管，按图组装。
Find appropriate shape's steel wire, carbon tube
from the landing gear accessories bag.
20
21
马达及像真件安装 Motor and Scale Parts Installation
自攻螺丝
拉线安装 Fasten the end of bracing wire with aluminium buckle
舵机安装示意图 Servo Installation
重心位置展示 CG Position Show
短
short
长
long
单边有两条拉线 ，按图中数字顺序进行安装，两条线用不同颜色表示。
U6
U3
U5
U5
U4
U4
碳管
拉线末端用铝扣固定
马达座根据选用马达的长度，调整马达座伸
出长度，然后用角型铝块加自攻螺定住。
2pcs wires on each side, assemble them according to the numerical order,
different wires with different colors in the picture. Fasten the end of bracing
wire with aluminium buckle.
Carbon tube
Adjust the extending length of
motor mounting board according
to your motor length, then fasten
with angle aluminum block and
self-tapping screw.
Self-tapping screw
F12
U1
F12 F13
爪牙螺母
Nut screws+F2-2
方碳管
Square carbon tube
裁剪粘贴橡胶条 Cut and stick rubber strip
碳管 Ø8x280mm
Carbon tube
Small Spring
螺丝+垫片
Screw+Spacer
There are two kinds of design for rear landing gear. One is
tail wheel, another one is skid wheel.See Figure 17 and 18,
please choose one design you like for installation.
Screw+Screw Cap
Screw+Screw Cap
U8
Screw+Screw Cap
Hinge
自攻螺丝
Self-tapping screw
3x3x90mm
C.G
≈245mm
22
2

像真件组装图示
Scale Parts Installation
像真引擎组装
Scale Engine Installation
按拆分图在像真引擎配件包中，找出相应的木
件，按图组装，连接处用胶水粘合。
Find appropriate wooden parts from the scale parts bag,
assemble it according to the split graph,glue the joints.
1-1 1-2 1-3
S20 1.2M Fokker-E Instruction Manual

Find appropriate wooden parts from the scale parts bag,
assemble it according to the split graph,glue the joints.
像真机枪组装
Scale Machine Gun Installation
按拆分图在像真机枪配件包中找出相应的木件，
按图组装，连接处用胶水粘合。
像真件完成后喷黑漆，然后安装到机身。
1-4
2-1
2-2
2-3
S20 1.2M Fokker-E Instruction Manual
Finished scale parts should be sprayed with
black paint, then install to the fuselage.
注意：拼装像真引擎时直径不要大于105mm
≤105mm
Note:The Diameter of scale engine cannot be more than 105mm.