Dancing Wings Hobby CESSNA150 User manual

F6
C2
F16
B17
F13
F12
F11
F15
F10
F14
F4
F5
F18
F18.5
F19
F20
F20
F21
F22
F6
F7.5
F5
A3
A3 F23
F24
F25
F22
A11
A8
PVC transparent shield
(pls cut the size yourself)
C3
X2
X5
X5
X1
Cut the suitable length
B3
B3
5.5x2mm balsawood strip
X6 X7
X4
X4
B14 B14
X1.5
B1
B6
B13
B5
B11
PVC transparent shield
(pls cut the size yourself)
screw
Wingspan:960mm
Length:820mm
Flying Weight:≈680g
Suggested Prop:9-10inch
Suggested Motor:2212 KV1100
Suggested ESC:20A 3S
Suggested Servo:9g servo*4
Suggested BATT:3S 1400-2000mah
Suggested Radio≥4CH
SPECIFICATION
TOOLS NEEDED
ACCESSORIES
1.Fuselage Assembly
A2
F17
PVC transparent shield
(pls cut the size yourself)
Cut the suitable length
5.5x2mm balsawood strip
Cut the suitable length
5.5x2mm balsawood strip
F26
Cut the suitable length
5.5x2mm balsawood strip
wood bar
C6
F9
F8
F7
c5
B7 B8 B9
c10
c9
c5
B5
B6
c10
c9
B4 B4
B14
B3
B2
B2
B16
B18 B1
B14
B12
B13
B12
B13 C8 c1
B3
B11
w8
w8
w3 w3
w1
w1
B19
B20
A16
A17
A17
A16
B21
B21
B22
B22
B23
B23
w10
w9
w11
w10
w7
w7
w12
w6
w6
w2
w2
w4
w4
w5
w5 456789 10 1223
A7
A6
A8
w11
w10
w12
w2
A14
w5
A11
A11
A12
A13 A12
A13
L2
w12
w9
w11
A9
A9 L1
L2
L1
A10
C2
F18
F6
G2
X7
F25
X4
X4
G2
X1.5
F15
B17
F7.5
F12
F12
F9
F5
X6 X7
B17
F14 F17
F5
F24
F5
F23
X2
A1
F20
F21 F22
F3
C6 F18.5
F19
A4
A5
F8 F7
A3
A3 X1 C3 X5
C4 F2
F16
F26
F4
A2
F13 F10
B4
B4
B2
B2
All manuals and user guides at all-guides.com

B7
A16
A16
A17
A12
A9
A9
C8
C1
A12
A13
A13
B8
A17
B9
B9
2. Vertical Fin Assembly
4.Landing Gear Assembly ≈60mm
Position of center of gravity
3.Wing Assembly
6.Power System Assembly
front wheel
pushrod
rudder
pushrod
elevator pushrod
Assemble the wing as per the 1:1 drawing,pls
assemble it on the desk and make ture the
flastness of the whole wing.Assemble the left and
right wing in same way.
L1,L2
Grinding into
wing's radian.
Snap the aileron's steel
wire linkage into slot.
Connect aileron here.
Note:Please finish linkage installation before sticking C10.
Use steel wire linkage to connect
servo's arm here.
Cut a gap here.
5.Assemble together the
wing,assemble the horizontal
and vertical fin onto the
fuselage,pls note the wing
must be fixed by screws.
Sand 5*6mm balsawood strip to circular arc.
All manuals and user guides at all-guides.com