Dancing Wings Hobby S19 Manual

A1-1
A1-2
A1-3
F20 F21
F14 F4 F5
F5-1
F5-2 F5-3x2
F5
F3
F2
F1x2
F16
F17
F17
F18
F23 F24
F18
F19
F15
F6
A1
A2
A1-4
F7
F8
F9F10
F11
F12
F22
F13
A4
F25
A6
A5
A3
注意：粘贴轻
木蒙板A5，A6时用少量水
湿润，方便弯曲后，再进行蒙板。
Note: Soak the balsa cover board A5
and A6 a little,bend and paste by glue.
C2
C6 C7 C4
E6
C1
C10
C8 C9
E2 C14
E4
E5
R3
R14
R15
R17 R5
R4
R16
R7
R18 R1
R10
R2
R11
R13
R8
R9
R9
R12
A7x2
注意：A7打磨成机身弧度,
然后粘贴机身尾部。
Note: Polish the A7 with fuselage
radian,and paste onto the tail of the
fuselage.
1
2
3
4
找出A1，A1-1用胶水粘合牢固后再进行下一步操作
Find out the board A1 and A1-1,then paste together by glue.
A1-2，A1-3，F20，F21对准孔位粘贴。
Paste the part A1-2,A1-3,F20 and F21 as per the holes.
7
8
9
10
5
6
11
机身组装Fuselage Assembly
尾翼组装 Tail Assembly 机翼组装 Wing Assembly
12
13
14
B1
B1
A8
A9 A10
A11
B2
B3
B4
B6B5 B8B7
碳杆 70mm
注意：粘贴轻木蒙板A8-A11时用少量
水湿润，方便弯曲后，再进行蒙板。
Note: Soak the balsa cover bord
A8-A11 a little,bend and paste
by glue.
正
Upper 背
Bottom
U1 U2 U3 U4 U5 U6 U7 U8 U9 U10
U22
U19 U19
U18
U18
U20
U21
Ø3m 碳杆420mm
U15
U11
U14
U13
U12
D11
D10
D26
D9
D7D8-1 D8
D6
D5
D4
D3
D2
D1
S19 Mini Tiger Moth Balsawood Airplane
       15
16
17
18
19
上机翼组装
Upper-wing Assembly
下机翼组装
Lower-wing Assembly
自攻螺丝
self-tapping screws
Suggested Equipment
Motor: 2212-2216 1000-1400KV
ESC: 20-30A
Propeller: 8-9 inch
Servos: 9g*4
Battery: 3s 1800-2200mAh
Radio≥4CH
Speci�ication
Wingspan: 980mm
Length: 812mm
Flying Weight≈700-750g
推荐配置
马达: 2212-2216 1000-1400KV
电调: 20-30A
桨叶: 8-9寸
舵机: 9g*4
电池: 3s 1800-2200mAh
通道≥4CH
参数
翼展: 980mm
机长: 812mm
起飞重量≈700-750g
电机安装示范
Motor Installation
A2
R
L
U
D
F
C11 C12
C13
E3
轻木条
Balsawood strip
按实际长度截取
Cut off as per the actual length
轻木条
Balsawood strip
按实际长度截取
Cut off as per the
actual length
把步骤2中拼贴好的侧板安装到步骤4的机身框架上。
Paste the finished side board in step 2 onto the
fuselage in step 4.
carbon rod
carbon rod
Note: Motor is optional
注意: 马达为选配

D27
D27-1 D18 D30
D12
D14
D15
D16
D17
D19
D13
D29
D28
D25
D29-1
此处Z1-Z4支架配件为1:1大小，请对
比此图找出配件进行安装。
Z1
Z1
Z2
Z2
Z3
Z3
Z4
Z4
机翼为可拆卸设计，用拉线固定。拉线为一条线，按下图顺序安装。
1为起始点，8为结束点，1和8用铝扣，固定在一起。
卡扣
Clip
可拆卡扣
自锁螺母
Self-locking nuts
自攻螺丝
螺丝+螺母
screws + nuts
自攻螺丝
Self-tapping screw
Self-tapping screw
自攻螺丝
舵机安装位置
servo installation position
各组件组装 Components Installation
20
副翼组装
Aileron Assembly
组装好的副翼通过纸合页和
机翼连接在一起，使副翼可
以45度摆动。
21
重心设置 C.G. Adjustment
可拆卸机翼，拉线安装图示
the wing is removable,the wiring installation as picture shown.
在机头部安装头罩，按所需颜色进行喷
漆，用自攻螺丝固定到机身。
Install the cowling at the head of
fuselage,paint in any color as per your
needs,finally firm with self-tapping
screws onto the fuselage.
自攻螺丝
Self-tapping screw
22
23
24
25 26
27
舵机及连杆安装图示
Installation of the Servo and Connection Rod
轻木条
Balsawood strip
按实际长度截取
Cut off as per the actual length
Connect the aileron with wing by
paper hinges,make sure the aileron
could swing 45 degree.
Here are the 1:1 plan for bracket
accessories Z1-Z4,pls find out and
install as picture shown.
Start at point 1,and end at point 8,then connect 1 and 8 together by Aluminum buckle.
Wing is removable,and firm with one wiring. Assemble the wiring in order as picture below.
Removable buckle
碳杆420mm
carbon rod
300mm
碳杆
carbon rod
Ø7m
Ø7m
Ø3m
Ø3m
≈70mm C.G