Dancing Wings Hobby T20 Sport Scale Cessna 152 User manual

S1
S2
S3
F2
F8
F3
安装爪牙螺母
Install nut screw 注意此处爪
牙螺母朝向
F3-1
Here please note
the nut direction.
Q5
S1-1
S1-2
F11-2
1
23
4
F4
F11x2
F1x2
F5
F9
F6 F7
3
6
F10-1
F10x2
7
5
轻木条
L15
L14
Q3 轻木条
轻木条 Q4
轻木条
S9
S10 磁铁
L6
L7
垫入第二片L7时，需稍加
打磨成斜面
圆木杆
Round wooden pole
L7
L11
注意：粘贴侧板时，有雕刻门
窗的一面朝外。
8 9
10 11
12
安装连杆导管到预留孔内,从舵机安装位
置到尾部。
安装前转向轮固定组件，用内六角螺丝固定
S6 S4
S7
S8
S5
S4-2 S4-2
S4-1
S11
S11
找出S1-S3轻木板，把他们如图粘贴在一起，待粘合
牢固后，再进行下一步骤。
机翼及尾翼请对比1:1图纸上的编号拼装，将图纸平铺到水平
工作台面上进行拼装，拼装时保持机翼平直。
拼装时注意以下细节图片
水平尾翼
Horizontal Tail
垂直尾翼
Vertical Tail
底部安装爪牙螺母
磁铁
Magnet
塑料合页
Plastic hinge
13
14
细节 Detail 1
机身组装 Fuselage Installation
机翼组装 Wing Installation
T20 Sport Scale Cessna 152 Instruction Manual
参数
翼展：1200mm
机长：870mm
起飞重量：≈1000-1200kg
推荐配置
推荐马达：2216-2814 900-1100KV
推荐电调：20A-40A
推荐电池：3S 2200-2800mAh
推荐舵机：9g*4pcs / 6pcs
推荐桨叶：9-11寸
通道≥4CH
Speci�ication
Wingspan: 1200mm
Length: 870mm
Flying Weight:≈1000-1200g
Electric power: 2216-2814 900-1100KV
ESC: 20A-40A
Battery: 3S 2200-2800mAh
Servo：9g*4pcs / 6pcs
Propeller: 9-11inch
Radio≥4CH
工具 Tools Needed
此处所用轻木
条请按实际长
度自行截取。
Here please cut
the balsawood
strips according
to the actual
length by
yourself.
S4-1
Suggested Equipment
Find out S1-S3 balsawood board, stick them
together as shown.Proceed next step after glueing
them firmly.
Install nut at the bottom.
Install nut on
the back.
背面安装爪牙
螺母
Note:Put the side with laser-cut
door and window outward when
you stick the sideboard.
Balsawood strip
Balsawood strip
Balsawood strip
Balsawood strip
此处所用轻木条请按
实际长度自行截取。
Here please cut
the balsawood
strips according to
the actual length
by yourself.
Install front-wheel steering fixed parts,
fix with hexagon screw.
Install link rod duct on the
reserved hole from servo
mounting location to tail.
Build the wing and tail wing according to 1:1
drawing plan.
Put the drawing plan on horizontal workbench for
building and keep the wing straightness.
Pay attention to below details
pictures during building.
细节 Detail 2
Please polish L7 to bevel
when you assemble the
second L7.
Magnet

副翼
Aileron
襟翼

L8-4
L9-4
副翼，襟翼拼装时在下图位置垫入轻
木片，方便安装舵角。
在机翼前缘粘贴L1-1，并打磨成机翼一体的
弧度。
16 17
15
18
内六角螺丝固定
Fasten soket head cap screw
起落架安装，在上图所示位置安装起落架。
Landing gear and other parts installation.
轮档固定
Fix wheel chock
前转向轮穿入步骤9安装的组件中，用顶丝锁定。
Insert front-wheel steering into the part
which installed on step 9, fix with top screw.
F13x2
起落架及各部件组装 Landing gear and other parts installation
马达及舵机安装图示
Motor and servo
installation show
粘贴后打磨成弧形
Sand to arc after sticking.
M2
W4-1
L2-1x2
19
自攻螺丝
Self-tapping screw
机翼支架
Wing bracket
20
D1
D1
21
安装马达时，根据所选用的马达的大小适当的垫入M1，使
马达可以正常运转。
Insert M1 according to the motor size you use during
installing motor.
Z型钢丝连杆穿入步骤10中预
装的套管中，并连接舵臂，舵
角，用快装接头固定。
Insert Z-shape steel wire link
rod into the drivepipe which
preassembled in step 10,
and connect rudder arm and
control horn, fix with quick
mounting connector.
如图安装舵机，舵角。
Install servo and control horn
as shown.
22
23
重心位置展示图示 CG position show
54mm C.G
调整电子设备及重心即可进行试飞。
Adjust the electric equipment
and C.G,then test the flight.
24
细节 Detail 3 细节 Detail 4 细节 Detail 5
细节 Detail 6
Stick L1-1 at the leading edge of wing, and
sand it to the same radian of wing.
Add balsawood sheet in below position
when you install aileron and flap,
convenient for installing control horn.
完成后的两部分机翼，通过L2-1对
插在一起，连接处大量胶水粘合。
Plug the two finished wings into
each other by L2-1, stick the joint
with a lot of glue.
前转向轮安装，在上
图所示位置安装前转
向轮。
Front-wheel steering
installation as shown.
内六角螺丝固定
Fasten soket head cap screw
自攻螺丝
Self-tapping screw
在下图位置，按实际长度截取轻
木条粘到舵机安装位置。
In below position, please cut
the balsawood strips according
to the actual length, stick it on
the servo installation position.
自攻螺丝
Self-tapping screw
自攻螺丝
Self-tapping screw
如图安装襟翼、副翼舵机，在襟翼和副
翼安装舵角，用Z型钢丝连杆连接舵臂
和舵角，通过快装接头锁定。
Install servos and control horns of
flap and aileron as shown,
Connect rudder arm and control
horn with Z-shape steel wire link
rod, lock with quick mounting
connectors.