Dancover PROSHED MS117050 User manual

for
Garden Shed
3,01x2,38x2,14m
Manual
11-06-2020

Metal Garden Shed
OWNER'S MANUAL
Instructions for Assembly
Requires two people
Quick & Easy Assembly
Ridge Reinforced Walls
Available in Various Sizes

BEFORE YOU START
Owner's Manual
Prior to installation, it is important that you contact your local government authority to
determine if building approval is required. Study and understand this owner's manual.
Important information and helpful tips will make your construction easier and more
enjoyable.
Assembly instructions
Instructions are supplied in this manual and contain all appropriate information for your
building model. Review all instructions before you begin. During assembly, follow the
step sequence carefully for correct results .Please be aware: this unit takes two people
about one full day to complete.
Parts
Check to be sure that you have all the necessary parts for the building.
Separate contents of the carton by the part number while reviewing parts list.
Familiarize yourself with the hardware and fasteners for easier use during
construction. These are packaged within the carton. Note that extra fasteners have been
supplied for your convenience.
TOOLS MAY REQUIRED
Use heavy duty gloves when handling steel sheets and flashing
PLAN AHEAD
Watch the weather:
Please be sure the day you select for installation is dry and calm.
DO NOT attempt to assemble your shed in windy weather
because of risk of damage to panels, or personal injury. Be careful
of wet or muddy ground.
Teamwork:
Whenever possible, two or more people should work together to
assemble the building. One person can position parts or panels
while the other is able to handle the fasteners and the tools.
It requires two people a full
day to complete installation

PLAN AHEAD
Site Selection
Avoid overhanging trees as much as possible as leaves will make regular cleaning
necessary and broken branches are a potential hazard.
Small trees,bushes or fences nearby can be helpful,acting as a wind break.
Site Preparation
The site must be prepared so that the base of the shed is level all round and checking
with a spirit level is required.
The base can be constructed by treated timber or concrete,in order to stop the moisture
getting into the shed.The shed is not designed to be built onto lawn directly.Also the
ground will get muddy during rainy days.
If a concrete pad is made,it is important that this slopes towards the edges to prevent
water ingress.
Time must be allowed for any concrete or cement to dry before building the shed on top.
Bases can also be constructed from bricks,blocks,or mounted on a concrete pad.
The bricks or blocks should be cemented onto firm and level concrete footings and the
shed frame drilled and screwed to the base.
IMPORTANT NOTES:
Find someone to help you:it is much easier with someone to hold parts,pass tools
ect.Also some steps require two people to lift structures together.This is not very
heavy work so would suit most able-bodied people.
Allow plenty of time:rushing often causes errors and the re-doing of incorrect
assemblies.If you have never built a shed before,it can take most of a day to carefully
complete the construction.
Have the right tools to hand.
Safety clothing as recommended in the 'Tools' section.
Ideally lat out the parts and check that all are present before commencing
construction.Lay on cloths or plastic sheets if there is any risk of scratching the parts.
Tighten all nuts carefully,being sure not to miss any.Check the frame is square and
using a spirit level to check that it is upright.

PART
NO. Qty.
1L
PART
NO. Qty.
2
2R
3L
1169mm
1R
2L
1244mm
4L
4R
5
6
7
8
9
10L
10R
11
13
14
15-1
15-2
16
3R
12
16-1
17L
17R
18
19
20
21L
21R
22L
22R
23L
23R
24-1
24-2
B1
B2
B3
B4
1169mm
916mm
916mm
1720mm
1720mm
1246mm
1304mm
1426mm
1426mm
1115mm
1439mm
1439mm
1115mm
356mm
1173mm
1173mm
1090mm
1090mm
1244mm
1540mm
1540mm
655mm
1090mm
1304mm
1118mm
1118mm
1304mm
1304mm
182mm
182mm
371mm
371mm
2
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
1
1
1
1
2
2
6
1
1
2
2
2
2
1
1
1
1
2
1
1
2
2
2
1490mm
1490mm
1439mm
1439mm

1720mm
PART
NO. Qty.
G2 4
2
GF
GD
GB
GC
4
4
F1
F2
F3
S3
420
9
65
384
S2 290
PART
NO. Qty.
1710X659mm
D1 1
D2 1
4
P1
P3
P4
P5
P6
P7
1540mm
2
5
4
2
2
2
P2 4
1710X659mm
P8 2
1540mm
1540mm
1540mm
2
GE
1720mm
1720mm
1720mm

13
14
16-1
16
13
14
21R
21L
21L
21R
12
B1 B3 B4
B2
12 B1
B3
B4
B2
11
9
1R
1R
1L
1L
2L
2R
3L
3R
5
22L
22R
23L
23R
P4
P3
P3
GE
GE
17R
17L
17L
17R
GC
GC
GC
GC
15-1
15-2
24-1
24-2
19
20
P6
P6
P5
P7
P7
P8
P8
P5
P2
22R
11
P3
P3
P3
10L
10R
P4
P4
P4
P2
22L
9
8
P1
P1
D1
D2
18
6
4R
4L
7
P2
P2

2L
2R
1R
1L
F1
F1
-7-
1L
PART
NO. Qty.
2
F1
1R
1L
1R 2
2L
PART
NO. Qty.
1
F1
2R
2L
2R 1
1L
1R
x2

PART
NO. Qty.
1
1
3L
3R
3L
3R
F1
F1
PART
NO. Qty.
1
5
5
F1 F1
1、When diagonal measurements are
equal,the frame is square.
2、The Floor Frame must be
BOTH square AND level or the
holes will not line up properly.
-8-

PART
NO. Qty.
P1 1
F1
S3
PART
NO. Qty.
1
PART
NO. Qty.
22R 1
S3 F1
-9-
F1
Ⅱ
Ⅰ
S3
P4
F2
S3
P1
P4
Ⅰ
Ⅱ
22R

PART
NO. Qty.
P2 1
F1
S3
PART
NO. Qty.
1
PART
NO. Qty.
22L 1
S3 F1
-10-
P4
F1
Ⅱ
S3
Ⅰ
P4
Ⅰ
Ⅱ
P2
22L
F1

PART
NO. Qty.
P3 1
F1
S3
PART
NO. Qty.
1
P4
F1
S3
F1
Ⅱ
S3
PART
NO. Qty.
23R 1
S3 F1
-11-
F1
23R
22L
Ⅰ
23R
P3
P4
Ⅰ
Ⅱ

PART
NO. Qty.
23L 1
S3 F1
-12-
PART
NO. Qty.
1
PART
NO. Qty.
1
P1
F1
S3
S3 F1
22R
F1
F1
23L
22R
P1

F1
Ⅱ
S3
PART
NO. Qty.
1
-13-
F2
S3
P4
PART
NO. Qty.
1
S3 F1
22L
F1
PART
NO. Qty.
2
9
2
11
Ⅰ
F1
P4
Ⅱ
Ⅰ
22L
9
11
11
9
F2

10L 10R
PART
NO. Qty.
1
10L
1
10R
-14-
x2
PART
NO. Qty.
GF 4
PART
NO. Qty. PART NO. Qty.
2
2
21L
21R
2
2
B3
B4
2
2
B1
B2
2
12
GF GF
x2
21L
21R
B4 B3
B1
B2 12
12
B3
21L
F2
10R
10L

-15-
P3
P3
87
G2
PART
NO. Qty.
1
7
1
8
G2 4
7
8
PART
NO. Qty.
3
P2
4
P3
PART
NO. Qty.
2
2
13
14
13
14
F2
P3
P3
P2
P2
P3
P3
P2
x2
7&8
G2

PART
NO. Qty.
1
16
1
16-1
F2
16
16-1
F2
12
F2
12
Ⅰ
F2
F2
Ⅱ
-16-
16
16-1
16-1
16
F1
Ⅲ
Ⅰ
Ⅱ
Ⅲ
Ⅲ
Ⅲ
Ⅲ
ⅡⅠ
14
13
14
13

-17-
4L
4R
6
PART
NO. Qty.
1
4L
1
4R
1
6
4R
6
F1
S3
PART
NO. Qty.
1
P5
P6 1
PART
NO. Qty.
2
P7
F1
S3
F1
S3
S3
F2
P5
P5
P6
P7
P7

-18-
PART
NO. Qty.
2
P8
PART
NO. Qty.
1
P5
P6 1
PART
NO. Qty.
2
17L
17R 2
F1
S3
F1
S3
P8
P8
P6
P5
17L
17R
F1
S3
17L
17R

-19-
PART
NO. Qty.
1
19
20 1
GE 2
F1
S3
F1
GE
17R
20
17L
PART
NO. Qty.
1
15-1&15-2
4
GC
1
24-1&24-2
15-2
24-1
15-1
24-2
Ⅰ
Ⅰ
PART
NO. Qty.
D1 1
D2 1
2
GB
x2
GB
F2
D1&D2
20
19
Ⅰ
Ⅱ
Ⅰ
Ⅱ
F1