Dancover PRO XL User manual

16-12-2019
Manual
for
Storage Tent PRO
3,5 Series PVC/PE

Safety Advice
Attention
In some countries approval is needed to set up a marquee/tent larger than 75 m2. It is your
responsibility to comply with local rules and regulations and to ensure that the marquee/tent is
assembled correctly.
In case of bad weather conditions, it is your responsibility to ensure the marquee/tent is safely
secured and that the marquee/tent does not cause damage to others.
Do not use open re, welding equipment or other sources which can ignite, inside or close to the
tent.
The marquee/tent must be safely secured. We recommend you secure your marquee/tent with
straps and pegs as soon as it is assembled.
Make sure to check if the marquee/tent is covered by your home contents insurance.
Marquees/tents must be evacuated under extreme weather conditions.
In the event of snow, always remove snow from the roof of the marquee/tent regularly to prevent
snow from building on the roof, as heavy snow can cause the marquee/tent to collapse.
In the event of rain, there is a risk of rain puddles building up on top of the roof of the marquee/
tent. Heavy rain puddles can cause the roof to collapse. It is your responsibility to ensure rain
puddles do not build up. As a precaution, make sure the roof of the marquee/tent is stretched
out properly and adequately over the side frames of the marquee/tent and remove rain water
regularly.
Do not unpack or repack your marquee/tent in freezing temperatures. In case of temperatures
below zero, always unpack and repack your marquee/tent indoors to avoid the risk of cracking
parts.
The marquee/tent must be totally dry before you repack and store it to avoid mildew.
Note: Marquees are intended for events and other arrangements and are as such only meant for
short term temporary assembly and the following disassembly. Dancover warranty applies only
to the normal use of the Product, normal wear and tear excepted, in accordance with written
use instructions or manual. The warranty does not apply to damage caused by accident, abuse,
misuse, or modication of the Product.
Warranty Information
Please visit dancovershop.com for information on warranty.
Please always check our website for the latest safety advice and manual.

Warning
1. In order to avoid being rusted by air, oil is covered on the surface of the pipes. Before setting
up the tent, please remove the oil carefully rst to keep the cover clean.
2. Take note that the tent needs to be handled carefully to avoid damage.
3. Do not force the frames as they may be damage in the process.
4. Tents are meant as temporary shelter, and must be evacuated under extreme weather
conditions.
Please, select a suitable site for the tent to avoid the damage of underground sprinkler systems,
water, gas or electrical lines.

Part no. 3.5x8m 3.5x10m
1Frame pole
1600mm 50-50 18 24
2Frame pole
1880mm 38-38 30 37
3Groundbar
1380mm 38-38 2 2
4Roof support
1730mm 25-25 5 6
5Frame pole
1600mm 50-50 4 4
6Diagonal support
1720mm 32-32 8 8
73-way connector
54-42/3 rings 4 4
83-way connector
54-42/2 rings 2 2
9Diagonal support
800mm 32-32 4 4
9-1 4-way connector
54-42/4 rings 3 4
10 Female doorbar
1835mm 32-32 2 2
10-1 4-way connector
54-42/4 rings 6 8
11 Lower leg
1600mm 50-50 8 8
12 Female doorbar
970mm 32-32 2 2
16-12-2019

Part no. 3.5x8m 3.5x10m
13 Strenghten bar
1845mm 32-32 2 2
14 3-way conntector
54-42 4 4
15 4-way connector
54-42 6 8
16 3-way connector
for corner 2 2
17 3-way connector
for corner 2 2
18 3-way connector
for sidewall 6 8
19 2-way connector
for endwall 2 2
20 Strengthen bar
980mm 32-32 2 2
21 Bracket 10 12
22 Groundbracket 8 10
23 Strengthen bar
1855mm 25-25 16 20
24 Turnbuckle for
door 4610mm 4 4
25 Turnbuckle for
roof 2550mm 16 20
16-12-2019

Part no. 3.5x8m 3.5x10m
26 Turnbuckle for
side 3700mm 16 20
27 Peg
10x350mm 16 20
28 Spiral peg 4 4
29 Small peg 38 42
30 Bungeeball long 56 56
31 M6 wingnut 22 24
32 Screw
M6x30mm 10 12
33 Screw
M6x45mm 10 10
34 Screw
M6x65mm 2 2
35 M6 nut 4 4
36 Spanner 2 2
37 Tie down 4 4
38 Steel clip 34 40
39 Screw
M8x50mm 64 78
40 Screw
M8x65mm 68 80
41 M8 nut 132 158
42 Peg
16x600mm 16 18
16-12-2019

Part no. 3.5x8m 3.5x10m
43 M12 washer 4 4
44 M12 nut 4 4
45 Screw
M12x48mm 2 2
46 Screw
M12x65mm 2 2
47 Sheaved block
1 wheel 2 2
48 Sheaved block
2 wheel 2 2
49 Ratchet stape 4 4
50 Roof 1 1
51 Endwall 2 2
16-12-2019

Part 33 Part 34 Part 35 Part 43 Part 44 Part 45 Part 46
M6x45
Screw
M6x65
Screw
M6
Nut
M12
Washer
M12
Nut
M12x48
Screw
M12x65
Screw
3.5x8 3.5x10 3.5x8 3.5x10 3.5x8 3.5x8 3.5x10 3.5x8 3.5x10 3.5x8 3.5x10
Used for Part 4 and Part 21 10 12
Used for Part 6 and Part 12 2
Used for Part 6 and Part 10 2
Used for Part 6 and Part 9 4
Used for Sheaved block 1wheel Part 47 2 2 2
Used for Sheaved block 2 wheel Part 48 2 2 2
Used for M6x30 10 12
Used for M6x45 10 10
Used for M6x65 2 2
Used for 2-way connector 19 4 4
Used for 3-way connector 7 4 4 8 8
Used for 3-way connector 8 2 2 4 4
Used for 3-way connector 14 4 4 8 8
Used for 3-way connector 16 4 4 2 2
Used for 3-way connector 17 4 4 2 2
Used for 3-way connector 18 12 16 6 8
Used for 4-way connector 9-1 6 8 6 8
Used for 4-way connector 10-1 12 16 12 16
Used for 4-way connector 15 12 16 12 16
Used for Part 6 and Part 11 4 4
Used for Part 9 and Part 11 4 4
Used for M8x50 64 78
Used for M8x65 68 80
Used for M12x48 2 2
Used for M12x65 2 2
22 24 10 12 10 2 4 64 78 68 80 132 158 4 4 2 2
M8
Nut
3.5x8-10x3.3m storage pro
Part 31 Part 32 Part 39 Part 40 Part 41
M6
Wing nut
M6x30
Screw
M8x50
Screw (Ø42)
M8x65
Screw (Ø54)
16-12-2019

I
tubes, tent and accessories... etc. are present and the same as the list.
Assemble the framework of rooftop by joining the portion (7, 8, 9-1, 10-1) together with poles (1, 2,
4, 5, 6, 12) NO. 11 is on four corners for diagonal pipe.
II
across through each section as below.
III
Attach one end of supported pole (1) to the joints.
If you want the rope pull at the opposite side
than shown in the drawing then switch
sheaved block (47) and (48)
48
47
7 7
7 7
4

IV
Attach the other supported poles (1, 2, 11) to the joints, built-up the framework. NO. 11 is on four
corners for diagonal pipe.
V
You facilitate the assembly and dismantling by pulling the roof with ropes on tent frame. Use the
steel clips to fasten the cover to the frame. Each section we offer bracket and nail to fasten the
frame to ground.
48
47