Dancover Storage Tent PRO User manual

04-10-2019
for
Storage Tent PRO
8x12x5,2m PVC
Manual

Safety Advice
Attention
In some countries approval is needed to set up a tent larger than 75 m2. It is your responsibility
to comply with local rules and regulations and to ensure that the tent is assembled correctly.
In case of bad weather conditions, it is your responsibility to ensure the tent is safely secured
and that the tent does not cause damage to others.
Do not use open re, welding equipment or other sources which can ignite, inside or close to the
tent.
The tent must be safely secured. We recommend you secure your tent with straps and pegs as
soon as it is assembled.
Make sure to check if the tent is covered by your home contents insurance.
Tents must be evacuated under extreme weather conditions.
In the event of snow, always remove snow from the roof of the tent regularly to prevent snow
from building on the roof, as heavy snow can cause the tent to collapse.
In the event of rain, there is a risk of rain puddles building up on top of the roof of the tent.
Heavy rain puddles can cause the roof to collapse. It is your responsibility to ensure rain
puddles do not build up. As a precaution, make sure the roof of the tent is stretched out
properly and adequately over the side frames of the tent and remove rain water regularly.
Do not unpack or repack your tent in freezing temperatures. In case of temperatures below
zero, always unpack and repack your tent indoors to avoid the risk of cracking parts.
The tent must be totally dry before you repack and store it to avoid mildew.
Note: Dancover warranty applies only to the normal use of the Product, normal wear and tear
excepted, in accordance with written use instructions or manual. The warranty does not apply
to damage caused by accident, abuse, misuse, or modification of the Product.
Warranty Information
Please visit dancovershop.com for information on warranty.
Please always check our website for the latest safety advice and manual.

1
8x12
1Back leg 4
2 18
4Crossbar 16
6Ceiling rail 11
5Ceiling rail 11
3Extension pipe 22
7Corner arch 22
8Center arch 11
9Connecting
pipe 117
10 Connecting
pipe 13
11 Extension pipe 22
12 Extension pipe 4
13 Door pillar 4
16 Foot base 26
17 Connecting
component 4
15 Fasten bar 20
04-10-2019
Back leg
Instruction
18 Nail
10x350mm 16
19 Nail
6x180mm 60
20 Nail
7x300mm 52
1

2
Spiral nail
10x700mm 4
23 1.75" Screw 12
24 2.5" Screw 40
25 4" Screw 148
26 Wing nut 200
27 Floor Bracket
(set of 2 pcs) 8
28 Bungee ball 92
29 Spanner 2
30 Bolt with nut 34
31 Tie-down kit 4
32 Steel clip 40
33 Steel wire 12
34 Rope 4
35 Rope 4
22 Cross bar 8
04-10-2019
36 Roof 1
37 Endwall 2
21

3
Attention
Please use gloves when assembling the metal frame of this unit. The metal components of this product have been treated,
with a rust preventive coating. This coating is not dangerous, but you may grease your hands during assembly. We
recommend that you wipe metal parts clean with a mixture of warm water and dish detergent prior to assembly. Should your
hands become dirty, simply wash with soap and water.
After the frame is set up, it should look like the picture shown below.
8x12

4
Please assemble the frame in these steps. All sizes have similar assemble step.
Step 2,
Step 3,
gnisurehtohcaehtiwstnemelehcraehttcennocwoN
the connecting pipes (9 and 10). Note that only corner
arch 10 are used for the front segments. Use the 4” screw
and wing nut to tighten them.
Step 4,
Strengthen the frame with steel wire.
Step 1
When assembling the tent, make sure that all the wing
nuts are attached to the inside.
Connect one center arch pipe(8) with the extension
pipe(11). Attach the corner arch(7) to the ends of the
extension pipe(3). Now connect the ceiling rail(6 and 5)
with each other using the 1.75" screw and the wing nuts.
Connect extension pipe (3) and (11) together then attach
ceiling rail to extension pipe(3 and 11) through 17 using
the 2.5" screws and wing nuts.
Repeat step 1 for the next elements and place them on
the ground one after another, as illustrated.

5
Step 5,
Start setting up one side first. Connect the corner arch 7) with the legs (1 and 2). Secure the frame using the connecting
pipes (9 and 10). Attach the diagonal pipes (4) to the back legs (1). Please refer to the completed frame pictures to attach the
diagonal pipes.
Screw tighten the tent at the feet, using the 4” screws and wing nuts.
Use the floor bracket and the 10x350mm pegs to fasten the frame to the ground.
Step 6,
Unfold the tent cover and put it over the frame. Insert the fasten bar(15) into the loop at the lower end of roof and fasten it with
steel clips. Attach the end wall to the frame using the bungees. Tension the roof cover to the tent frame to the ground using
the 6x180mm pegs.
(

6
Step 7,
Assemble the pillar set like on the picture below.
Step 8,
Use the ropes to attach the door and cover to the frame. Find a proper way and strength to attach the cover to the frame
carefully. Please do not use too much strength to tear the eyelet out of fabric.

Contact information
Head office:
Dancover A/S
Nordre Strandvej 119 G
3150 Hellebæk
Denmark
For more information
please visit:
www.dancovershop.com
National contact
Denmark: 70 26 76 20
[e-mail]
UK: 020 8099 7570
[e-mail]
Spain: 911 436 828
[e-mail]
Italy: 02 479 21 198
[e-mail]
Germany: 041 0266 7040
[e-mail]
Switzerland: 0840 000125
[e-mail]
France: 0975 181 800
[e-mail]
Austria: 0662 626935
[e-mail]
Sweden: 040 233 262
[e-mail]
Finland: 0 931 581 720
[e-mail]
Nederland: 0 858 880 524
[e-mail]
Poland: 22 300 8602
[e-mail]
Ireland: 0 151 33 003
[e-mail]
Luxembourg: [phone]
[e-mail]
Portugal: 308 800 899
[e-mail]
Belgium: 0 28 08 08 09
[e-mail]
Norway: 231 00 690
[e-mail]