Dancover Pagoda Tent EventZone User manual

3x3m 4x4m & 5x5m
Manual for
Pagoda Tent EventZone
20-08-2013

Safety Advice
Attention
In some countries approval is needed to set up a marquee/tent larger than 75 m2. It
is your responsibility to comply with local rules and regulations and to ensure that
the marquee/tent is assembled correctly.
In case of bad weather conditions, it is your responsibility to ensure the
marquee/tent is safely secured and that the marquee/tent does not cause damage
to others.
close to the tent.
The marquee/tent must be safely secured. We recommend you secure your
marquee/tent with straps and pegs as soon as it is assembled.
Make sure to check if the marquee/tent is covered by your home contents insurance.
Marquees/tents must be evacuated under extreme weather conditions.
In the event of snow always remove snow from the roof of the marquee/tent
regularly to prevent snow from building on the roof as heavy snow can cause the
marquee/tent to collapse.
In the event of rain there is a risk of rain puddles building up on top of the roof of the
marquee/tent. Heavy rain puddles can cause the roof to collapse. It is your responsi-
bility to ensure rain puddles do not build up. As a precaution, make sure theroof of
the marquee/tent is stretched out properly and adequately over the side frames of
the marquee/tent and remove rain water regularly.
Please always check our website for the latest safety advice and manuall.
Note: Marquees are intended for events and other arrangements and are as such only
meant for short term temporary assembly and the following disassembly. Dancover
warranty applies only to the normal use of the Product, normal wear and tear excepted,
in accordance with written use instructions or manual. The warranty does not apply to

11
3
3
3
1
3
1
3
1.) Take the eave-connector and push in the bolt, then fit the
eave-purlin overthe tube 40x40 until the bolt (2) slids in the hole.
Repeat for all 4 corners, see drawing above.
1
2
Push the bolt and take the eave purlin over the eave knuckle
Side view
Top view
Eave purlin
Eave purlin
1

1
4
4
4
4
1
44
2.) Take the beams (4) and fit these in eave-connectors (1).
Repeat at all four eave corners.
1
11
4
Top view
Eave purlin
Floor
Side view Roof beam
40x40x2
Eave purlin
Eave purlin
Roof beam
Eave purlin
2

5
5a
5
4
4
4
4
3.) Take the ridge-piece (5) and turn the spindle (5a) down until the top
comes out 3 cm. Lift the beams (4) to fit them in the ridge connectors,
smoothly.
5
5a
Top view
Eave purlin
Eave purlinEave purlin
Eave purlin
Side view
Ridge connector
Floor
Roof beam
40x40x2
3

3
6
5
7
8
3
5a
4.) Fit the top-cap (6) onto the spindle (5a) and put the roof-cover
over the frame. Fix the in the channel-groove (7)
of the roof-cover (8) on all 4 sides. Hook the track-device in the
eave-purlins (3) and span the roof by turning the spindle (5a) until
the required tensioning is reached.
8
4
Floor
Side view
Hooking track
device
mast top
Floor
Side view
Hooking track
device
mast top

99
1
5.) Lift the 4 legs and push the bolt (10), slide the legs overthe eave
connector until the bolt slids in.
9
10
5
Leg
Base plate
Floor
Side view

11 11
12 12
11
6.) Take the pagoda in position. After this fix the side-covers. Hit the
earth-anchors (11) into the available holes of the base-plate (12).
Each pagoda, comes with 4 earth-anchors.
12
6
Earth anchor
Base plate
Base plate
Floor
Floor
Earth anchor
Side view

Contact information
Head office:
Dancover A/S
Nordre Strandvej 119 G
3150 Hellebæk
Denmark
For more information
please visit:
www.dancovershop.com
National contact
Denmark:
[e-mail]
UK:
[e-mail]
Spain:
[e-mail]
Italy:
[e-mail]
Germany:
[e-mail]
Switzerland:
[e-mail]
France:
[e-mail]
Austria:
[e-mail]
Sweden:
[e-mail]
Finland:
[e-mail]
Nederland:
[e-mail]
Poland:
[e-mail]
Ireland:
[e-mail]
Luxembourg:
[e-mail]
Belgium:
[e-mail]
Norway:
[e-mail]