Dancover Basic-1339H User manual

SHELTER
Assembly Manual
W4xL12xH5,5 m
17-10-2012

Congratulations on your purchase of our instant shelter. This unit is a combination of
excellent manufacturing and design. It is comprised of a rigid frame and a durable cover. For
easy assembly, we have marked all the parts with codes. With proper installation, use and
maintenance, your unit will provide many years of good and suitable service.
READ ALLTHE INSTRUCTIONS BEFOREASSEMBLY！
1. The proper erection and installation of this building requires a high level of care and safety.
We recommend the safety regulations be complied with during the installation. It includes
but is not limited to:
-Safety hats, protective eyewear and protective clothing
-Safety harnesses for all elevated workers
-Proper ladder, cage, and safety operation
2. Site selection: Choose a solid level location for your building. Do not install the building
where the ground could not keep the building steady. Do not install the building where the
ground could not bear the weight of the building. Do not install the building in soft grass
ground or wetland.
3. Be cautious with the surroundings. Keep work area clean. Do not set up it near snow drifts, in
slippery places, or in wet location. The cover of the building will protect against normal
falling leaves and light debris, however, large, fast or sharp falling items etc. may cause a
puncture or tear in the cover material. So, keep the building away from such harmful things.
Be careful with power and heat sources. Don’t keep heat sources near the tarpaulin. Don’t
expose to open flame.
4. Chose a windless day to install the building. It is very difficult to attach the cover in heavy
wind.
5. All snow accumulation on the main cover should be removed as soon as possible. Otherwise,
when old snow on the roof becomes hard with new snow falling in, it will increase the
burden of the roof badly and will damage the roof.
6. Try to keep the building, especially its base, in a dry condition. This will help the building to
have a longer life than keeping it in a wet condition.
7. The user should be responsible for the parts missing or damage occurred during the
installation.
8. Don’t make alteration of the frame. Don’t hang anything besides included parts to the frame.
Damages, consequential damages, or injuries caused by improper installation, alteration,
improper use, or damages caused by snow, wind, or any acts of nature are owing to the user.
The building is not intended for occupancy for any length of time.

ASSEMBLY PROCEDURE
1. Prepare location and place all unit boxes near location sight. Perform an inventory check
before beginning, to be certain all components are available for installtion.
2. Secure base plate flanges to base surface.
3. Assemble every group of arch.
4. Begin frame assembly with front end arch, first interior arch, purlins, etc.
5. Add to assemble other groups of arches.
6. Install main cover over frame.
7. Install end covers over end panels.
Read all the detailed instructions and notices in the following assembly instructions!
MAINTENANCE AND CARE
1. If some parts or the cover were accidently damaged during the use, contact the local supplier
for advises on the repairing method or replacements, so that to prevent from further damage
and keep the building in a good condition.
2. When replacing the parts, make certain the whole frame and the parts connected to the
replaced parts be well fixed or supported.
3. Same with when attaching the cover, choose a windless day to replace the cover. Begin with
making certain all the bolts of the frame and the tensioning equipments be well fixed. When
taking off the cover, make sure the related ropes, etc. be taken off, and the cover will not be
blocked during the way. Avoid taking off the cover with heavy big power equipments.
4. To enlongate the life of the cover, put small duct tape or foam rubber (provide it by yourself)
on the frame that comes to in contact with cover. The tape and foam rubber acts as a cushion
to avoid rubbing damage to the cover over years.
5. Periodically (once in half a year or more often), the building should be completely inspected
and maintained internally and externally to make certain the building remains properly
installed and secured. Including: check all bolts and hardware connectors to be certain they
are in place and tightened, the base plates are still fixed firmly, check and adjust the ropes if
in need, clean the cover with suitable washing. Allowing dirt and debris to sit on cover over
an extended time will damage cover irreparably.
Thanks again for choosing this quality product. The following is the detailed assembly
instructions for you starting the assembly.

Part Code Description Quantity
1 Top roof curved tube 7
2 Shoulder tube 12
2B Shoulder tube in front panel 2
2A Upper sidewall tubes 14
3 Lower sidewall tubes 14
4 Horizontal wall and roof purlin 42
5 Base flange of four corner of frame 4
6 Base flange of backwall tube in the middle 1
7 Base flange of sidewall tubes 10
9 Vertical support tube for cross tube in the front wall 1
10 Upper Cross tube in the front and back wall (2 pcs per set) 2sets
12 Standing tube in the middle of back wall 2
13 Lower Cross tube for back wall 4
14 Tensioning tube for back cover at the bottom 2
16 Ground support tube in the front wall (2 pcs per set) 1set
17 M10x60 bolt for upper cross tube in front&back panel 4
17A M6x40 bolt for ground support tube in front wall 1
17B m10x75 bolt for swaged connection 116
17C M10x30 bolt for connection angle 8
17D M10x15 bolt for tie down ratchet 28
18 M10x90 bolt for horizontal tube 51
20 Connecting angle for four conners of the frame 8
21 Roof cover 1
22 Lower roof cover tensioning tube 2sets
23 Tie down ratchet 14
24 Nylon bands for tensioning roof cover 14
25 Back cover 1
27 Front cover 1
29 Ropes for fastening the roof cover and the front&back cover 10
30 Tube for opening and closing door 1
31 Stake peg 44
32 Door dropping tube 1set
33 Plastic cap for cover tensioning tube 12
34 Windstabilizers on both sides of the shelter 8sets
35 Door pulley 2
36 Rope for door 2
Part List of Model#Basic-1339H(L12.0xW4.0xH5.5m)