Dancover CA119011 User manual

06-07-2017
for
Folding Garage (Car)
2,5x5,4x2m
Manual

TABLE OF CONTENTS
1. GENERAL INFORMATION……………………………………………………………….…....3
1.1 Introduction………………………………………………………………………………...........3
2. BOX DESCRIPTION AND TECHNICAL SHEET………………………………………....….4
2.1 General description…………………………………………………………………………......4
2.2 Components………………………………………………………………………………..……5
2.3 Fabric’s characteristics……………………………………………………………………..…..8
3. INSTALLATION…………………………………………………………………………..........10
3.1 Handling and transport…………………………………………….......................................10
3.2 Place and requirements for the installation…………………………………………….…...10
3.3 Installation…………………………………………………………………………………...…10
3.3.1 Package opening……………………………………………………………………………10
3.3.2 Squared holding devices placement………………………………………………..........11
3.3.3 Box installation…………………………………………………………………………..….11
3.3.4 Bracing system………………………………………………………………….……..........12
3.3.5 Snails opening…………………………………………………………………………..…. .13
4. BOX UTILIZATION…………………………………………………………………….…….. .13
5. CHECKS AND MAINTENANCE………………………………………………………..........14
6. DISASSEMBLY…………………………………………………………………………….…..14
2

1. GENERAL INFORMATION
1.1. Introduction
This manual is an integral part of the product; it is addressed to the installer and to the final user of
the box, and enables a correct installation and use. For this reason it must be hold with the box
until proper disposal.
In this manual you will find the instructionsto:
•
•
•
•
correctly install the box
understandthe functions of the box and of the whole thereof
correctly do the box scheduled maintenance processes
take care of the basic safety rules
ATTENTION: the installer and the final user must read the whole manual in each part of
it. Keepthis manual in a safe and accessible place.
Before using the box, please read carefully the technical information contained in this
manual and follow them strictly.
3

4
2. BOX DESCRIPTION AND TECHNICAL SHEET
2.1. General description
The box must be used only as an ordinary protection cover, for purely temporary use. In case of
bad weather conditions (wind, snow), the box must be removed. Given that the box can not be
fixed to the ground - but only bound to it - its use in these conditions can cause damages to
people and things.
It is particularly important for safety not to hang or apply any type of load at the structure or at the
top cover of the box.
In particular, children must not handle the snails. The failure to respect the conditions of use and
warnings immediately voids the warranty.
BOX MODULARE/BOX MODULARE ECO 1 snail
BOX MODULARE/BOX MODULARE ECO 2 snails
A (cm): 410/480/550
B (cm): 250
C (cm): 200
A (cm): 470/540/610
B (cm): 250
C (cm): 200

5
2.2. Components
N. DESCRIPTION
1 ALUMINIUM PROFILE MM 45X15
2 ALUMINIUM PROFILE (gables)
3 SQUARED HOLDING DEVICE
4 SQUARED HOLDING DEVICE CAP
5 ANODIZED ALUMINIUM 120x60 FOOT
6 PVC COVERSOL/FABRITARP TOP COVER
7 ALUMINIUM LACQUERED RAL 9010 PLATE (crosses)
8 ALUMINIUM LACQUERED RAL 9010 PLATE (tension bars)
9 NYLON ROPE DIAM. MM 5
10 STRING FASTENER HANDLE
11 HINGE FASTENING RIVET
12 TENTMESH LATERAL COVER (only for Box Modulare)
13 FOOT WITH FINAL HINGE
14 FOOT WITH CENTRAL HINGE
15 FOOT WITH HINGE FOR HEAD-FASTENING PLATE

6

7
10
8
7
12
9

8
2.3. Fabric’s characteristics
COVERSOL
BOX MODULARE
Yarn Warp: 100% PES 280 Dtex
Weft: 100% PES 280 Dtex
Construction Warp: 16 yarn/cm
Weft: 16 yarn/cm
Fabric’s weight Ca 400 gr/m2
Tensile strength Warp: Ca 120 DaN/5 cm
(DIN 53354) Weft: Ca 130 DaN/5 cm
Tearing resistance Warp: Ca 5,5 DaN
(DIN 53363) Weft: Ca 7,5 DaN
Grip (ISO 2411) Ca 6 DaN/5 cm
Temperature resistance +70°C/-30°C
Light resistance (DIN 53388) Level: 7/8
Finishing Gloss lacquered (one side)
UV Treated

9
LG 450
BOX MODULARE ECO
Coating PVC
Fabric’s weight Ca 450 gr/m2
Tensile strength Warp: Ca 250 DaN/5 cm
(DIN 53354) Weft: Ca 180 DaN/5 cm
Tearing resistance Warp: Ca 25 DaN
(DIN 53363) Weft: Ca 25 DaN
Hot / cold resistance +70° C/ -30°C
Finishing 1 side gloss lacquered

10
3. INSTALLATION
3.1. Handling and transport
The box installation should only be done by qualified staff.
The products must be unloaded through appropriate lifting equipment, which must be used only by
authorized staff.
If the unloading operation is made by hand, it is important to consider that the weight limit that each
person can handle is 25 Kg; moreover, the operators should be equipped with gloves and safety
shoes.
3.2. Place and requirements for the installation
Before the arrival of the installers the user must arrange:
•any permits required by local regulations
•appropriate ground
3.3. Installation
Before starting the installation, if electrical equipment utilization is needed:
•make sure you do not work in wet areas
•use only intact extension cords, according to the place of use
•use shoes with rubber soles
ATTENTION: it is necessary for the operators to use appropriate personal protective
equipment such as safety shoes and gloves, in order to avoid injuries provoqued by the
fall of the packaging or of components that it contains, perforation and cutting due to
cutting or hanging parts.
3.3.1. Package opening
Packaging must be opened only with scissors with rounded tips, using the best care not to cut the
cloth of the article (Photo 1).
P
H
O
T
O
1