Dancover Garage tent 3,77x7,3x3,24m PVC User manual

3,77x7,3x3,24m PVC
Garage tent
Manual
13-12-2013

Safety Advice
Attention
In some countries approval is needed to set up a marquee/tent larger than 75 m2. It
is your responsibility to comply with local rules and regulations and to ensure that
the marquee/tent is assembled correctly.
In case of bad weather conditions, it is your responsibility to ensure the
marquee/tent is safely secured and that the marquee/tent does not cause damage
to others.
close to the tent.
The marquee/tent must be safely secured. We recommend you secure your
marquee/tent with straps and pegs as soon as it is assembled.
Make sure to check if the marquee/tent is covered by your home contents insurance.
Marquees/tents must be evacuated under extreme weather conditions.
In the event of snow always remove snow from the roof of the marquee/tent
regularly to prevent snow from building on the roof as heavy snow can cause the
marquee/tent to collapse.
In the event of rain there is a risk of rain puddles building up on top of the roof of the
marquee/tent. Heavy rain puddles can cause the roof to collapse. It is your responsi-
bility to ensure rain puddles do not build up. As a precaution, make sure theroof of
the marquee/tent is stretched out properly and adequately over the side frames of
the marquee/tent and remove rain water regularly.
Please always check our website for the latest safety advice and manuall.

Assemble manual
DEAR CUSTOMER
Assembly with more than one person suggested.
Please use gloves when assembling the metal frame portion of this unit.
The metal components of this product have been treated
with a rust preventive coating that may feel oily to the
touch. This coating is not dangerous, but may dirty your
hands during assembly. We recommend that you wipe
metal parts clean with a mixture of warm water and dish
detergent prior to assembly. Should your hands beco me
dirty, simply wash with soap and water.
Frame view
3,77 meter series
1
1
3
3
7
7
4
4
5
5
10 9
8
8
8
8
8
8
8
8
811
11
11
2
2
2
2
6
Drawing is of an is 3,77x5x3,24m

13-12-2013

1. Assembly of middle arches
a) Take one arch (no. 4); assemble with one main corner arch
(No.7) on the left side.
b) Take the other corner arch (no.7) on the right side.
c) Take one completed arch; put screw 1-3/4" (No.18) through
holes on the right side and attach bar ( no.5) over screw and
tighten wing nut(No.20)
d) Repeat same procedures on the left side.
2. Repeat step 1 for the remaining middle arches.
3. Assembly of end arches (Wing nuts are always on inside of
the shelter)
a) Take one arch (No.4); assemble with one end corner arch
(No.3) on the left side.
b) Take one complete arch ,put 1 3/4” screw through holes on the
right side and attach bar (no.5 ) over screw and tighten wing
nut
c)Slide the hooks (No.16) over bars(No.10) then put other
side(No.9) attach one end to arch (No.3)with 1 3/4” screws and
wing nut.
d) Take the other corner arch (No.3) on the right side.
d) Repeat step 3 with the remaining arch.
g) Place one of the last arches assembled at the front of the
shelter, the other at the back.
4. Assembly of legs
a) Insert (No.1) legs into an end arch one side at a time.
b) Insert (No.2) legs to the second arch.
c) Add second arch to assembly connecting (No.8) into (No.11)
with screw 3” (No.21 )and diagonal bar (No.6) with screws 2 ½”
(No.21) with wing nuts (No.20). See sketch at front page. Note:
(No.11) should be placed at last section.
d) Repeat step b) and c) until the whole shelter is completed.
No.18 1-3/4" Bolt 16 18 20 22 24
N0.19 2-1/2" Bolt 3 3 3 3 3
No.20 Wing Nut 43 50 57 64 71
No.21 3"Bolot 27 32 37 42 47
No.22 Roof 1 1 1 1 1
N0.23 Endwall 2 2 2 2 2
A
B
C
D
143-3/4”

e) Make sure the base is open to 143 3/4”.
f) Make sure the distances AD and BC have exactly the same
length as per illustration, lengths depends on the model.
5. Cover installation (Ties are always on the inside)
a) Place the roof in front of the shelter as illustrated.
b) Unfold as illustrated then lift onto shelter as is.
c) Place cover over the completed structure making sure that the
TRIANGLE is at the front of the garage.
d)Attach all straps inside of the roof to the structure poles going
comletely around the garage.
e) Tie firmly inside ties to bars.
f) Grommets are placed in the upper corner of each door .Put the
cord through these grommets and secure to the ground with
nails.
6. Door Assembly
a) Take one door with shiny side facing outside placing on to
hooks (No.17).
b) Repeat a) for the remaining doors.
c) Take the elastic, put it through one of the grommet holes on the
door from the inside out. Take S hook, place it on the elastic and
squeeze one end with a pair of pliers so it locks on the elastic.
Repeat until all the elastics are done, and then use the open end
to hook on the grommet band of the roof.
7. Anchoring garage.
a) Place your garage in the final position you want then close the
doors, front and back if supplied before anchoring, anchor with
brackets (No.14) and nail (No.13) as per diagram on the first
page. Drive anchor into ground.
b) Fix flap to your house (if applicable).

Contact information
Head office:
Dancover A/S
Nordre Strandvej 119 G
3150 Hellebæk
Denmark
For more information
please visit:
www.dancovershop.com
National contact
Denmark:
[e-mail]
UK:
[e-mail]
Spain:
[e-mail]
Italy:
[e-mail]
Germany:
[e-mail]
Switzerland:
[e-mail]
France:
[e-mail]
Austria:
[e-mail]
Sweden:
[e-mail]
Finland:
[e-mail]
Nederland:
[e-mail]
Poland:
[e-mail]
Ireland:
[e-mail]
Luxembourg:
[e-mail]
Belgium:
[e-mail]
Norway:
[e-mail]