Danfoss OPX Series User manual

Classified as Business
User Manual
Danfoss Wireless Control Panel OPXxx
(DRAFT)
Danfoss A/S
Ulsnaes 1
DK-6300 Graasten
vlt-drives.danfoss.com

Classified as Business
TABLE OF CONTENTS:
1. The wireless Control Panel 4
2. Installation Instructions 5
2.1 Safety and Installation Awareness ................................................................5
2.2 Verifying Shipment and Contents..................................................................5
2.2.1 Items Supplied........................................................................................5
2.2.2 Control Panel Compatibility.....................................................................6
2.3 Installing the Control Panel ...........................................................................6
2.4 Status Indicators ...........................................................................................7
2.5 Installation instruction for best radio reception...............................................8
2.5.1 Wireless CP installed in a drive...............................................................8
2.5.2 Wireless CP installed remotely in a cradle..............................................9
2.6 Installation Illustrations................................................................................10
2.6.1 Illustrations ...........................................................................................10
3. Connection Procedure 11
3.1 Access Point Mode .....................................................................................11
3.2 Client mode.................................................................................................11
3.3 LED pattern.................................................................................................12
3.3.1 Status indicators...................................................................................12
3.3.2 Wireless indicators –Access Point Mode .............................................12
3.3.3 Wireless indicators –Client Mode.........................................................12
4. Safe control 13
5. Approvals and certifications 14
5.1 EU Declaration of Conformity......................................................................14
5.2 FCC compliance notice...............................................................................14
5.3 RF Exposure compliance............................................................................15
6. Technical specifications 16

Classified as Business
Version log:
Version
Initials
Date
Comments
0.0
EGK
08.12.2021
Document started

Classified as Business
1. The wireless Control Panel
The main functionality of the wireless CP is to setup and control a drive manually via the build-in
menu or/and act as a wireless gateway for this purpose (the wireless option is needed).
The application MyDrive® Insight can be installed on mobile, tablets, etc. device. Download
MyDrive® Insight from Google Play, Apple Store or go to Danfoss Drives App Suite.
Control Panel 2.8W OPX25: with display, NFC and wireless; 136b7732
Control Panel 2.8 OPX21: with display and NFC; without wireless; 136b7731
Wireless Panel OPX01: without display; with NFC and wireless; 136b7733
Control Panel 2.8 - OPX21 Wireless Panel –OPX01
Control Panel 2.8W –OPX25

Classified as Business
2. Installation Instructions
2.1 Safety and Installation Awareness
Before starting installation, familiarize yourself with the safety guidelines and precautions in the
Safety Guide. For additional information about the control panel, consult Application Guides in the
iC7 Series.
2.2 Verifying Shipment and Contents
2.2.1 Items Supplied
Make sure that the items supplied consist of any of the following control panel options.

Classified as Business
2.2.2 Control Panel Compatibility
All iC7 hardware products are compatible with the control panel options either mounted into the
cradle in the iC7 drive, or front mounted and connected by a cable. For installation instructions on
control panel mounting kits, see iC7 Series Control Panel Mounting Kits.
2.3 Installing the Control Panel
Procedure to attach control panel:
1. See illustration 1.1–1.3 in 2.6.1 Illustrations
Result
•The clip makes a click sound when properly aligned. The control panel is now locked into
the cradle.
•A splash screen is shown during the power-up of the control panel. Check status indicator
lights on the control panel. Refer 1.4 Status Indicators.
•After the control panel is powered on, the Home screen is shown. If security is enabled, the
control panel display navigates to an Authentication screen.
2. To use MyDrive® Insight, install and launch MyDrive® Suite from Google Play, Apple
Store or go to Danfoss Drives App Suite. Skip the step, if MyDrive® Suite is already
installed.
3. Open MyDrive® Suite and install MyDrive® Insight.
Procedure to detach control panel:
1. See illustration 2.1–2.3 in 2.6.1 Illustrations

Classified as Business
2.4 Status Indicators
The status of the drive is represented via the Halo and text LED indicators. The Halo and text LED
indicators are available on all control panel options. The text LED indicators are Warn, Ready, and
Fault.
Status indicators:

Classified as Business
2.5 Installation instruction for best radio reception
This gives “Best Praxis” hints for setting up a drive with a wireless Control Panel or the remote
placement of a wireless Control Panel.
2.5.1 Wireless CP installed in a drive
Best location for a drive with a wireless ICP:
•In general, it is good praxis to keep the drive clear from the ground/floor
•Keep it as clear as possible from other objects, particularly the font side
•Do not place obstacles in front of the drive
•If the drive has to be placed inside a cabinet use an extension cable to get the wireless ICP
outside the cabinet
•Avoid places near other radiating devices e.g., router, transmitter, …

Classified as Business
2.5.2 Wireless CP installed remotely in a cradle
Best praxis for a remotely placed wireless control panel in a cradle:
•It is good praxis to place the cradle clear from the ground/floor in a vertical position
•Use only original Danfoss extension cables
•Keep it as clear as possible from other objects
•Keep a minimum clearance of 10cm from other cables behind the wireless control panel
•Do not place obstacles in front of the wireless control panel
•Avoid places near other radiating devices e.g., router, transmitter, …

Classified as Business
2.6 Installation Illustrations
2.6.1 Illustrations

Classified as Business
3. Connection Procedure
Default operation mode is Off but can be configured for Access Point Mode or Client Mode
operation from parameter xx-xx-yy WiFi Operation Mode.
xx-xx-yy
WiFi Operation Mode
Access_Point_Mode
Client_Mode
Off
3.1 Access Point Mode
The wireless SSID is Danfoss following the serial number of the iC7 Product. For example,
Danfoss-012345678900 is the default wireless SSID for a product with the serial number
012345678900. The serial number can be located on the product label or alternatively from
parameter xx-xx-0x Serial Number. Default Password is Danfoss1234
xx-xx-0x
AP Wireless SSID
Danfoss-012345678900
•Open the MyDrive Insight app and establish the Wi-Fi connection, see table for descriptions
of the white Wi-Fi LED.
•When prompted, change the default password due to security restrictions. The password
must be at least 8 and maximum 48 characters.
If the password is not changed, it leaves only 10 minutes for connecting and performing operations.
After this, the wireless connection closes.
Reset password
If password is forgotten, it can be reset from MyDrive Insight through the NFC interface on the
control- or wireless panel or through the Service Port.
3.2 Client mode
xx-xx-1x
CM Wireless SSID
Danfoss-123456789
xx-xx-1y
CM Password
123456789
•Open the MyDrive Insight app and establish connection either wired or wireless.
•Configure the Client Mode SSID and Password according to the access point
•Configure Wi-Fi Operation Mode to Client Mode operation

Classified as Business
3.3 LED pattern
3.3.1 Status indicators
Status
Panel options
Status type
Control Panel 2.8W
Status type
Power On Not Ready
Blinking White (1Hz)
Power On Not Ready
Ready for operation
On White
Ready for operation
Fault
On Red
Fault
Warning
On Yellow
Warning
Winking from external
application
Blinking (Yellow/White/Red)
Winking from external
application
3.3.2 Wireless indicators –Access Point Mode
Wi-Fi Status
Panel options
Wi-Fi Status type
Control Panel 2.8W
Wi-Fi Status type
Wi-Fi not active
LED indicator shows no color.
White Halo on control panel.
Wi-Fi not active
Wi-Fi is active (Devices are
connected or not connected)
LED indicator shows white
color.
White Halo on control panel.
Wi-Fi is active (Devices are
connected or not connected)
3.3.3 Wireless indicators –Client Mode
Wi-Fi Status
Panel options
Wi-Fi Status type
Control Panel 2.8W
Wi-Fi Status type
Wi-Fi not active
LED indicator shows no color.
White colored halo on control
panel.
Wi-Fi not active
Wi-Fi is active (Devices
are not connected)
LED indicator shows white
color. White colored halo on
control panel.
Wi-Fi is active (Devices
are not connected)
Wi-Fi is active (Devices
are connected)
LED indicator shows white
color. White colored halo on
control panel.
Wi-Fi is active (Devices
are connected)

Classified as Business
4. Safe control
The safe control configuration allows the product to decide the behavior in cases where connectivity
is lost from MyDrive Insight to the product through the Wi-Fi interface. This is only applicable
when the product is in running operation.
xx-xx-2x
Wi-Fi Timeout Action
Do nothing (Product continues
to run)
Stop the motor (Generic term
to be found because product
could be a grid converter or
an Active Front End)

Classified as Business
5. Approvals and certifications
5.1 EU Declaration of Conformity
The Control Panels comply with the following directives:
2014/53/EU Radio Equipment Directive
2011/65/EU RoHS Directive: Restriction of the use of certain hazardous substances
The following standards were consulted to assess conformity:
EN 300 328 v2.2.2
EN 300 330 v2.1.1
EN 301 489-1: v2.2.3 -17: v3.2.4
EN 60529:1991+A1:2000+A2:2013
IEC 62368-1: 2018
The CE symbol confirms that this product conforms with the above-mentioned norms and
regulations.
The complete DoC can be found on Danfoss website: www.Danfoss.com.
5.2 FCC compliance notice
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by 1 or more of the following
measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
•Consult the dealer or an experienced radio/television technician for help.

Classified as Business
Modifications: Any modifications made to this device that are not approved by Danfoss may void
the authority granted to the user by the FCC to operate this equipment.
5.3 RF Exposure compliance
FCC Radiation Exposure Statement:
This device complies with FCC’s and IC’s RF radiation exposure limits set forth for an
uncontrolled environment under following conditions:
1. This device should be installed and operated such that a minimum separation distance of 20 cm is
always maintained between the radiator (antenna) & user’s/nearby person’s body.
2. This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
3. Changes or modifications not expressly approved by the party responsible for compliance could
void the user´s authority to operate the equipment.

Classified as Business
6. Technical specifications
Wireless Standards: WiFi: 802.11 b/g/n
BT classic v4.2
BLE v4.2
Frequency range: 2.4…2.5 GHz
Output power: WiFi < 20 dBm
BT < 10 dBm
WiFi security: WPA2 (Personal)
WiFi operating mode: Access Point or Client
Operating temperature: -10 °C to +45 °C (+14 °F to +113°F)
Operating humidity: 5–90% RH, non-condensing
Ingress protection: IP20 (IP55 with gasket)
Electrical rating: 12V +/- 2V, 140mA
Dimensions: 122.5 x 77.1 x 15.5 mm (l*w*th)
4.8 x 3.0 x 0.6 in (l*w*th)
Weight: 112 g
3,91 oz
Firmware update: MyDrive Insight V1 or higher
NFC type: Passive tag
NFC standard: ISO/IEC 14443, part 2 and part 3 compliant
Frequency: 13,56MHz
…end