Danfoss Vlt drivemotor fcp 106 User manual

Items Supplied

•

Local operating panel (LOP), 175N0128 IP 65, see

Illustration 1.1.

•

Fixture for LOP, 175N2717 (included in 175N0128),

see Illustration 1.2.

•

LOP cable.

Illustration 1.1 Local Operation Panel (LOP) 175N0128 IP 65

Illustration 1.2 Fixture for LOP 175N2717 (included in 175N0128)

Installation Instructions

LOP Connection and Set-up

VLT®DriveMotor FCP/FCM 106

Safety Instructions

Refer to VLT

DriveMotor FCP 106 and FCM 106 Operating

Instructions for detailed information about safety precautions

for installation.

WARNING

DISCHARGE TIME

The frequency converter contains DC-link capacitors, which

can remain charged even when the frequency converter is

not powered. High voltage can be present even when the

warning LED indicator lights are o. Failure to wait the

specied time after power has been removed before

performing service or repair work can result in death or

serious injury.

1. Stop the motor.

2. Disconnect AC mains, permanent magnet type

motors, and remote DC-link supplies, including

battery back-ups, UPS, and DC-link connections to

other frequency converters.

3. Wait for the capacitors to discharge fully, before

performing any service or repair work. The duration

of waiting time is specied in Tabl e 1.1.

Voltage

[V]

Power Range

[kW]

Minimum waiting

time

(min)

3x400 0.55–7.5 4

Table 1.1 Discharge Time

1) Power ratings relate to NO, see VLT

DriveMotor FCP 106 and FCM 106

Operating Instructions.

Connection to FCP 106 or FCM 106

1. Connect the LOP as shown in Table 1.2 and

Illustration 1.3.

2. After completing connections, cut o or isolate

excess wire.

3. Connect terminal 27 V to +24 V or set

parameter 5-12 Terminal 27 Digital Input to [0] No

operation.

Terminal Dual-speed

operation

Dual-mode

operation

Dual-direction

operation

18 Purple Gray

19 –

27 Brown

29 Green

12 Red

50 Yellow

55 Blue

Table 1.2 Electrical Connections

Illustration 1.3 LOP Connections to FCP 106 or FCM 106

Installation Instructions LOP Connection and Set-up

VLT

DriveMotor FCP/FCM 106

Set-up

1. Perform set-up according to Table 1.3.

2. Use the [+]/[-] keys to set reference.

3. At power-up, the unit is always in stop mode. The set reference is stored during power down. To set up permanent start

mode, connect terminal 12 to terminal 19 and do not connect purple/gray wire to terminal 12. Permanent start mode

disables the stop function on the LOP.

Function Settings Key I (Start) Key II (Start)

Key (Stop)

Default - Dual speed operation

(connect purple or orange wire)

No changes to factory setting. Run on set

reference (+/-)

Run on 5 Hz

jog speed

Stop (and reset

- if trip)

Function 2 - Dual-mode

operation

(connect purple or orange wire)

Select the modes of operation in set-ups 1 and 2.

Set parameter 0-10 Active Set-up to [9] Multi Set-up.

Set parameter 5-13 Terminal 29 Digital Input to [23] Set-up

select bit 0.

Run with

set-up 1

Run with

set-up 2

Stop (and reset

- if trip)

Function 3 - Dual direction

operation (connect gray wire)

Set parameter 4-10 Motor Speed Direction to [2] Both

directions.

Set parameter 5-13 Terminal 29 Digital Input to [11] Start

reversing.

Run forward Run reverse Stop (and reset

- if trip)

Table 1.3 LOP Operation Mode

1) Set jog speed in parameter 3-11 Jog Speed [Hz]

2) When reset is required, set parameter 5-11 Terminal 19 Digital Input to [1] Reset.

Installation Instructions LOP Connection and Set-up

VLT

DriveMotor FCP/FCM 106

Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products already on

order provided that such alterations can be made without subsequential changes being necessary in specifications already agreed. All trademarks in this material are property of the respective companies. Danfoss