Danfoss VLT AutomationDrive FC 302 with Connectors User manual

NOTICE
VLT
®
AutomationDrive FC 302 with connectors is
NOT UL approved.
The ETR functionality is not guaranteed.
General rating: Enclosure IP55.
2 Safety Instructions
WARNING
DISCHARGE TIME
The frequency converter contains DC-link capacitors, which
can remain charged even when the frequency converter is
not powered. Failure to wait the specified time after power
has been removed before performing service or repair work,
could result in death or serious injury.
1. Stop the motor.
2. Disconnect AC mains, permanent magnet type
motors and remote DC-link power supplies,
including battery back-ups, UPS, and DC-link
connections to other frequency converters.
3. Wait for the capacitors to discharge fully, before
performing any service or repair work. The duration
of waiting time is specified in Table 2.1.
Voltage
[V]
Power range
[kW]
Minimum waiting
time (minutes)
3x400 0.55–7.5 4
High voltage can be present even when the warning LED indicator
lights are off.
Table 2.1 Discharge Time
3ItemsSupplied
Depending on the ordering number, the following is supplied:
FC 302 with connectors - 2 motor connectors (134N3195)
Illustration 3.1 2 Motor Connectors
Installation Instructions
VLT® AutomationDrive FC 302 with Connectors
Danfoss A/S © Rev. 06/2014 All rights reserved. MI04G102

FC 302 with connectors - 4 motor connectors (134N3196)
Illustration 3.2 4 Motor Connectors
FC 302 with connectors - side view
Illustration 3.3 Side View
For overall dimensions, refer to the VLT
®
AutomationDrive FC
302 Design Guide.
NOTICE
See the VLT
®
AutomationDrive FC 302 Design Guide for
further information.
4 Connectors
4.1 Overview
The frequency converter has 7 connectors plus 2 or 4 motor
connectors
Label Connector Description
X1 Mains Mains in M23 (in M25) Male
X2.1-X2.4 Motor Motor connection M23 Female
X51 PROFIBUS - Male PROFIBUS M12
X52
PROFIBUS -
Female PROFIBUS M12
X11-X14 I/O box connector Phoenix I/O box
Table 4.1 Connectors
4.2 X1- Mains M23 (in M25) Male
General ratings
•
Pins 1, 2, 3 and 4: 480 V AC, maximum 15 A
•
Pins C and D: 30 V DC, maximum 3 A
•
Tightening torque: 1.5–2.0 Nm
Pin Label Connected to frequency
converter wiring schematic
Min. wire
[mm
2
]
1L1 91(T1) 2.5
4L2 92(T2) 2.5
3L3 93(T3) 2.5
2PE 95(PE) 2.5
D 0 V DC 35 2.75
C 24 V DC 36 2.75
Table 4.2 Wire/Connector Assignment for Plug X1
Mating part: Mains X1 (female)
Phoenix order number.: KK-0885/XX,XX
Installation Instructions VLT® AutomationDrive FC 302 with Connectors
2 Danfoss A/S © Rev. 06/2014 All rights reserved. MI04G102

4.3 X2.1-X2.4 Motor Connectors M23 (in M25)
Female
General ratings
•
Pins 1, 2, 3 and 4: 480 V AC, maximum 15 A
•
Pins C and D: 30 V DC, maximum 3 A
•
Tightening torque: 1.5–2.0 Nm
Pin Label Connected to frequency
converter wiring schematic
Min. wire
[mm
2
]
1U 96(U) 2.5
3V 97(V) 2.5
4W 98(W) 2.5
2PE 95 2.5
Table 4.3 Wire/Connector Assignment for Plug X2
Mating part: Motor X2 (male)
Phoenix order number.: KCX-K0341/XX,XX
Max. cable length 7.0 m
4.4 2 Motor Connection Variant (134N3195)
Keep blind plugs installed at all times to keep the enclosure
tight.
Label Connected to frequency converter wiring schematic
X2.1-B 53
X2.2-A 50
X2.1-A and
X2.2-B Connected to a common terminal
X2.1-C and
X2.2-C
Connected to an open terminal available in the
frequency converter
X2.1-D and
X2.2-D
Connected to an open terminal available in the
frequency converter
Table 4.4 2 Motor Connection
4.5 4 Motor Connection Variant (134N3196)
Label Connected to frequency converter wiring schematic
X2.1-B 53
X2.4-A 50
X2.1-A and
X2.2-B Connected via an internal terminal
X2.2-A and
X2.3-B Connected via an internal terminal
X2.3-A and
X2.4-B Connected via an internal terminal
Table 4.5 4 Motor Connection
4.6 X51 PROFIBUS M12 Male, X52 PROFIBUS
M12 Female
General ratings
•
30 V DC, maximum 1 A
•
Tightening torque: 0.2–0.3 Nm
Label Connected to frequency converter PROFIBUS
connector
15VDC 67
2 63
30VDC 66
4 62
Table 4.6 PROFIBUS Connection
Mating part: PROFIBUS X52 and X51 (female/male)
Phoenix order number.: SAC-2P-MSB/ XX,XX-910/FSB SCO CT
4.7 X11-X14 I/O Connector Box
Phoenix sensor/actuator box - SACB-4/4-L-0,57HPUR CDA -
1531426
Tightening torque slot sensor/actuator cable 0.4 Nm
Label Wire Connected to frequency
converter wiring schematic
X11-X14 1 Brown 12 +24 V Out
X11-X14 2
X11-X14 3 Blue 20 COM D IN
X14-4 Grey 33 D IN
X13-4 Yellow 29 D IN/OUT
X12-4 Green 19 D IN
X11-4 White 18 D IN
Table 4.7 Connector Box
5 Installation
NOTICE
For installation, refer to the VLT
®
AutomationDrive FC 302
Operating Instructions.
Installation Instructions VLT® AutomationDrive FC 302 with Connectors
MI04G102 Danfoss A/S © Rev. 06/2014 All rights reserved. 3

Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products already on
order provided that such alterations can be made without subsequential changes being necessary in specifications already agreed. All trademarks in this material are property of the respective companies. Danfoss
and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.
Danfoss A/S
Ulsnaes 1
DK-6300 Graasten
www.danfoss.com/drives
*MI04G102*
MI04G102130R0611 Rev. 06/2014