Danfoss VLT AutomationDrive FC 302 User manual

MAKING MODERN LIVING POSSIBLE
Operating Instructions
VLT®AutomationDrive FC 302
90–1200 kW
www.danfoss.com/drives

Contents
1 Introduction 4
1.1 How to Read these Operating Instructions 4
1.1.1 Approvals 4
2 Safety Instructions and General Warning 6
2.1 Safety Regulations 6
2.1.1 Disposal Instruction 6
2.1.2 Caution 6
2.1.3 Software Version 6
2.1.4 High Voltage 6
2.1.5 Safety Instructions 6
2.1.6 General Warning 7
2.1.7 Before Commencing Repair Work 7
2.1.8 Avoid Unintended Start 7
2.1.9 Safe Torque Off (STO) 7
2.1.10 IT Mains 7
3 How to Install 8
3.1 Pre-installation 8
3.1.1 Planning the Installation Site 8
3.1.2 Receiving the Frequency Converter 8
3.1.3 Transportation and Unpacking 8
3.1.4 Lifting 8
3.1.5 Mechanical Dimensions 11
3.1.6 Rated Power 18
3.2 Mechanical Installation 19
3.2.1 Tools Needed 19
3.2.2 General Considerations 19
3.2.3 Terminal Locations - Enclosure Type D 20
3.2.4 Terminal Locations - E Enclosures 23
3.2.5 Terminal Locations - Frame size F 28
3.2.6 Cooling and Airflow 32
3.2.7 Installation on the Wall - IP21 (NEMA 1) and IP54 (NEMA 12) Units 34
3.2.8 Gland/Conduit Entry - IP21 (NEMA 1) and IP54 (NEMA12) 34
3.2.9 IP21 Drip Shield Installation (Enclosure Types D1 and D2) 36
3.3 Field Installation of Options 36
3.3.1 Installation of Duct Cooling Kit in Rittal Enclosures 36
3.3.2 Installation of Top-only Duct Cooling Kit 37
3.3.3 Installation of Top and Bottom Covers for Rittal Enclosures 37
3.3.4 Installation of Top and Bottom Covers 38
Contents VLT®Automation Drive FC 300 Operating Instructions
MG33U402 - Rev. 2013-12-16 1

3.3.5 Outside Installation/NEMA 3R Kit for Rittal Enclosures 38
3.3.6 Outside Installation/NEMA 3R Kit of Industrial Enclosures 39
3.3.7 Installation of IP00 to IP20 Kits 39
3.3.8 Installation of IP00s D3, D4, & E2 Cable Clamp Bracket 39
3.3.9 Installation on Pedestal 39
3.3.10 Installation of Mains Shield for Frequency Converters 40
3.3.11 Installation of Input Plate Options 40
3.3.12 Installation of D or E Loadshare Option 41
3.4 F Enclosure Panel Options 41
3.4.1 Enclsoure Type F Options 41
3.5 Electrical Installation 43
3.5.1 Power Connections 43
3.5.2 Grounding 54
3.5.3 Extra Protection (RCD) 54
3.5.4 RFI Switch 54
3.5.5 Torque 54
3.5.6 Shielded Cables 55
3.5.7 Motor Cable 55
3.5.8 Brake Cable for Frequency Converters with Factory Installed Brake Chopper Op-
tion 56
3.5.9 Load Sharing 56
3.5.10 Shielding against Electrical Noise 56
3.5.11 Mains Connection 56
3.5.12 External Fan Supply 57
3.5.13 Fuses 57
3.5.14 Mains Disconnectors - Frame Size D, E and F 69
3.5.15 F-Frame Circuit Breakers 69
3.5.16 F-Frame Mains Contactors 69
3.5.17 Motor Insulation 70
3.5.18 Motor Bearing Currents 70
3.5.19 Brake Resistor Temperature Switch 70
3.5.20 Control Cable Routing 70
3.5.21 Access to Control Terminals 72
3.5.22 Electrical Installation, Control Terminals 72
3.5.23 Electrical Installation, Control Cables 73
3.5.24 Switches S201, S202, and S801 75
3.6 Connection Examples 76
3.6.1 Start/Stop 76
3.6.2 Pulse Start/Stop 76
3.7 Final Set-Up and Test 77
Contents VLT®Automation Drive FC 300 Operating Instructions
2 MG33U402 - Rev. 2013-12-16

3.8 Additional Connections 78
3.8.1 Mechanical Brake Control 78
3.8.2 Parallel Connection of Motors 78
3.8.3 Motor Thermal Protection 79
4 How to Programme 80
4.1 The Graphical and Numerical LCP 80
4.1.1 How to Programme on the Numerical Local Control Panel 81
4.1.2 Initial Commissioning 82
4.2 Quick Setup 83
4.3 Parameter Menu Structure 85
5 General Specifications 90
6 Warnings and Alarms 105
6.1 Status Messages 105
6.1.1 Warnings/Alarm Messages 105
Index 117
Contents VLT®Automation Drive FC 300 Operating Instructions
MG33U402 - Rev. 2013-12-16 3

1 Introduction
1.1 How to Read these Operating
Instructions
The frequency converter is designed to provide high shaft
performance on electrical motors. Read this manual
carefully for proper use. Incorrect handling of the
frequency converter may cause improper operation of the
frequency converter or related equipment, shorten lifetime
or cause other troubles.
These Operating Instructions help starting, installing,
programming, and troubleshooting the frequency
converter.
Chapter 1 Introduction introduces the manual and informs
you about the approvals, symbols, and abbreviations used
in this literature.
Chapter 2 Safety Instructions and General Warning entails
instructions on how to handle the frequency converter
correctly.
Chapter 3 How to Install guides through mechanical and
technical installation.
Chapter 4 How to Programme shows how to operate and
programme the frequency converter via the LCP.
Chapter 5 General Specifications contains technical data
about the frequency converter.
Chapter 6 Warnings and Alarms assists in solving problems
that may occur when using the frequency converter.
Available literature
•The VLT AutomationDrive 90-1200 kW Operating
Instructions provide the necessary information for
getting the frequency converter up and running.
•The VLT AutomationDrive FC 301/302 Design Guide
entails all technical information about the
frequency converter and customer design and
applications.
•The VLT AutomationDrive Programming Guide
provides information on how to programme and
includes complete parameter descriptions.
•The VLT AutomationDrive Profibus Operating
Instructions provide the information required for
controlling, monitoring and programming the
frequency converter via a Profibus fieldbus.
•The VLT AutomationDrive DeviceNet Operating
Instructions provide the information required for
controlling, monitoring and programming the
frequency converter via a DeviceNet fieldbus.
Danfoss technical literature is also available online at
www.danfoss.com/drives.
1.1.1 Approvals
Table 1.1
The frequency converter complies with UL508C thermal
memory retention requirements. For more information,
refer to the section Motor Thermal Protection in the Design
Guide.
NOTICE
Imposed limitations on the output frequency
(due to export control regulations):
From software version 6.72 the output frequency of the
frequency converter is limited to 590 Hz. Software
versions 6x.xx also limit the maximum output frequency
to 590 Hz, but these versions cannot be flashed, i.e.
neither downgraded nor upgraded.
The following symbols are used in this document:
WARNING
Indicates a potentially hazardous situation which could
result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation which could
result in minor or moderate injury. It may also be used
to alert against unsafe practices.
NOTICE
Indicates important information, including situations that
may result in damage to equipment or property.
Introduction VLT®Automation Drive FC 300 Operating Instructions
4 MG33U402 - Rev. 2013-12-16
1
1

Conventions
Numbered lists indicate procedures.
Bullet lists indicate other information and description of
illustrations.
Italicised text indicates
•cross reference
•link
•footnote
•parameter name, parameter group name,
parameter option
60°AVM 60°Asynchronous Vector Modulation
A Ampere/AMP
AC Alternating current
AD Air discharge
AI Analog Input
AMA Automatic Motor Adaptation
AWG American wire gauge
°CDegrees Celsius
CD Contant discharge
CM Common mode
CT Constand Torque
DC Direct current
DI Digital Input
DM Differential mode
D-TYPE Drive Dependent
EMC Electro Magnetic Compatibility
ETR Electronic Thermal Relay
fJOG Motor frequency when jog function is
activated
fMMotor frequency
fMAX The maximum output frequency the frequency
converter applies on its output
fMIN The minimum motor frequency from
frequency converter
fM,N Nominal motor frequency
FC Frequency converter
g Gram
Hiperface®Hiperface®is a registered trademark by
Stegmann
hp Horsepower
HTL HTL encoder (10-30 V) pulses - High-voltage
Transistor Logic
Hz Hertz
IINV Rated Inverter Output Current
ILIM Current limit
IM,N Nominal motor current
IVLT,MAX The maximum output current
IVLT,N The rated output current supplied by the
frequency converter
kHz Kilohertz
LCP Local Control Panel
lsb Least significant bit
m Meter
mA Milliampere
MCM Mille Circular Mil
MCT Motion Control Tool
mH Millihenry Inductance
min Minute
ms Millisecond
msb Most significant bit
ηVLT Efficiency of the frequency converter defined
as ratio between power output and power
input
nF Nanofarad
NLCP Numerical Local Control Panel
Nm Newton Meters
nsSynchronous Motor Speed
On-line/Off-line
Parameters
Changes to on-line parameters are activated
immediately after the data value is changed.
Pbr,cont. Rated power of the brake resistor (average
power during continuous braking)
PCB Printed Circuit Board
PCD Process Data
PELV Protective Extra Low Voltage
PmFrequency converter nominal output power as
HO
PM,N Nominal motor power
PM motor Permanent Magnet motor
Process PID The PID regulator maintains the desired speed,
pressure, temperature, etc.
Rbr,nom The nominal resistor value that ensures a
brake power on motor shaft of 150/160% for 1
minute
RCD Residual Current Device
Regen Regenerative terminals
Rmin Minimum permissible brake resistor value by
frequency converter
RMS Root Mean Square
RPM Revolutions Per Minute
Rrec Resistor value and resistance of the brake
resistor
s Second
SFAVM Stator Flux oriented Asynchronous Vector
Modulation
STW Status Word
SMPS Switch Mode Power Supply
THD Total Harmonic Distortion
TLIM Torque limit
TTL TTL encoder (5 V) pulses - Transistor Transistor
Logic
UM,N Nominal motor voltage
V Volts
VT Variable Torque
VVCplus Voltage Vector Control
Table 1.2 Abbreviations
Introduction VLT®Automation Drive FC 300 Operating Instructions
MG33U402 - Rev. 2013-12-16 5
11

2 Safety Instructions and General Warning
2.1 Safety Regulations
2.1.1 Disposal Instruction
Equipment containing electrical
components may not be disposed of
together with domestic waste.
It must be separately collected with
electrical and electronic waste according
to local and currently valid legislation.
2.1.2 Caution
WARNING
The frequency converter DC link capacitors remain
charged after power has been disconnected. To avoid
electrical shock hazard, disconnect the frequency
converter from the mains before carrying out
maintenance. Before doing service on the frequency
converter wait at least the amount of time indicated
below
380-500 V 90-200kW 20 minutes
250-800kW 40 minutes
525-690V 37-315kW 20 minutes
355-1200kW 30 minutes
Table 2.1 Discharge Time
2.1.3 Software Version
VLT AutomationDrive
Operating Instructions
Software version: 7.1x
These Operating Instructions can be used for all VLT
AutomationDrive frequency converters with software version
7.1x.
The software version number can be seen from 15-43 Software
Version.
2.1.4 High Voltage
WARNING
The voltage of the frequency converter is dangerous
whenever the frequency converter is connected to
mains. Incorrect installation or operation of the motor or
frequency converter may cause damage to the
equipment, serious personal injury or death. The
instructions in this manual must consequently be
observed, as well as applicable local and national rules
and safety regulations.
WARNING
Installation in high altitudes
380-500 V: At altitudes above 3,000 m, contact Danfoss
regarding PELV.
525-690 V: At altitudes above 2,000 m, contact Danfoss
regarding PELV.
2.1.5 Safety Instructions
•Make sure the frequency converter is properly
connected to earth.
•Protect users against supply voltage.
•Protect the motor against overloading according
to national and local regulations.
•Motor overload protection is not included in the
default settings. To add this function, set
1-90 Motor Thermal Protection to value ETR trip or
ETR warning. For the North American market: ETR
functions provide class 20 motor overload
protection, in accordance with NEC.
•The earth leakage current exceeds 3.5 mA.
•The [Off] key is not a safety switch. It does not
disconnect the frequency converter from mains.
Safety Instructions and Gen... VLT®Automation Drive FC 300 Operating Instructions
6 MG33U402 - Rev. 2013-12-16
22

2.1.6 General Warning
WARNING
Touching the electrical parts may be fatal - even after
the equipment has been disconnected from mains.
Also make sure that other voltage inputs have been
disconnected, such as load-sharing (linkage of DC
intermediate circuit), as well as the motor connection for
kinetic back-up.
When using the frequency converter: wait at least 40
minutes.
Shorter time is allowed only if indicated on the
nameplate for the specific unit.
CAUTION
The earth leakage current from the frequency converter
exceeds 3.5 mA. To ensure that the earth cable has a
good mechanical connection to the earth connection
(terminal 95), the cable cross section must be at least 10
mm2or 2 rated earth wires terminated separately. For
proper earthing for EMC, see chapter 3.5.2 Grounding.
Residual Current Device
This product can cause a D.C. current in the protective
conductor. Where a residual current device (RCD) is used
for extra protection, only an RCD of Type B (time
delayed) shall be used on the supply side of this
product. See also RCD Application Note MN90GX02
(x=version number).
Protective earthing of the frequency converter and the
use of RCDs must always follow national and local
regulations.
2.1.7 Before Commencing Repair Work
1. Disconnect the frequency converter from mains.
2. Disconnect DC bus terminals 88 and 89 from load
share applications.
3. Wait for discharge of the DC-link. See period of
time on the warning label.
4. Remove motor cable.
2.1.8 Avoid Unintended Start
While the frequency converter is connected to mains,
the motor can be started/stopped using digital
commands, bus commands, references or via the Local
Control Panel (LCP):
•Disconnect the frequency converter from mains
whenever personal safety considerations make it
necessary to avoid unintended start.
•To avoid unintended start, always activate the
[Off] key before changing parameters.
•An electronic fault, temporary overload, a fault in
the mains supply, or lost motor connection may
cause a stopped motor to start. The frequency
converter with Safe Stop provides protection
against unintended start, if the Safe Stop
Terminal 37 is deactivated or disconnected.
2.1.9 Safe Torque Off (STO)
To run Safe Torque Off, additional wiring for the frequency
converter is required, refer to Safe Torque Off Operating
Instructions for Danfoss VLT
®
Frequency Converters for
further information.
2.1.10 IT Mains
Parameter 14-50 RFI Filter can be used to disconnect the
internal RFI capacitors from the RFI filter to ground in the
380-500 V frequency converters. This reduces the RFI
performance to A2 level. For the 525-690 V frequency
converters, 14-50 RFI Filter has no function. The RFI switch
cannot be opened.
Safety Instructions and Gen... VLT®Automation Drive FC 300 Operating Instructions
MG33U402 - Rev. 2013-12-16 7
22

3 How to Install
3.1 Pre-installation
3.1.1 Planning the Installation Site
CAUTION
Before performing the installation it is important to plan
the installation of the frequency converter. Neglecting
this may result in extra work during and after instal-
lation.
Select the best possible operation site by considering
the following (see details on the following pages, and
the respective Design Guides)
•Ambient operating temperature
•Installation method
•How to cool the unit
•Position of the frequency converter
•Cable routing
•Ensure the power source supplies the correct
voltage and necessary current
•Ensure that the motor current rating is within the
maximum current from the frequency converter
•If the frequency converter is without built-in
fuses, ensure that the external fuses are rated
correctly.
3.1.2 Receiving the Frequency Converter
When receiving the frequency converter, make sure that
the packaging is intact, and be aware of any damage that
might have occurred to the unit during transport. In case
damage has occurred, contact immediately the shipping
company to claim the damage.
3.1.3 Transportation and Unpacking
Before unpacking the frequency converter it is
recommended that it is located as close as possible to the
final installation site.
Remove the box and handle the frequency converter on
the pallet, as long as possible.
3.1.4 Lifting
Always lift the frequency converter in the dedicated lifting
eyes. For all D and E2 (IP00) enclosures, use a bar to avoid
bending the lifting holes of the frequency converter.
176FA245.10
Illustration 3.1 Recommended Lifting Method, Enclosure Types
D and E
WARNING
The lifting bar must be able to handle the weight of the
frequency converter. See Mechanical Dimensions for the
weight of the different enclosure type. Maximum
diameter for bar is 2.5 cm (1 inch). The angle from the
top of the frequency converter to the lifting cable should
be 60°or greater.
130BA832.11
Illustration 3.2 Recommended Lifting Method, Enclsoure Type
F1 (460 V, 600 to 900 HP, 575/690 V, 900 to 1150 HP)
How to Install VLT®Automation Drive FC 300 Operating Instructions
8 MG33U402 - Rev. 2013-12-16
33

130BA834.11
Illustration 3.3 Recommended Lifting Method, Enclosure Type
F2 (460 V, 1000 to 1200 HP, 575/690 V, 1250 to 1350 HP)
130BA833.11
Illustration 3.4 Recommended Lifting Method, Enclosure Type
F3 (460 V, 600 to 900 HP, 575/690 V, 900 to 1150 HP)
130BA835.11
Illustration 3.5 Recommended Lifting Method, Enclosure Type
F4 (460 V, 1000 to 1200 HP, 575/690 V, 1250 to 1350 HP)
130BB753.10
Illustration 3.6 Recommended lifting method, Enclosure Type
F8
130BB688.10
Illustration 3.7 Recommended lifting method, Enclosure Type
F9/F10
How to Install VLT®Automation Drive FC 300 Operating Instructions
MG33U402 - Rev. 2013-12-16 9
33

130BB689.10
Illustration 3.8 Recommended lifting method, Enclosure Type
F11/F12/F13/F14
NOTICE
The plinth is provided in the same packaging as the
frequency converter but is not attached to enclosure
types F1-F4 during shipment. The plinth is required to
allow airflow to the frequency converter to provide
proper cooling. The F enclosures should be positioned
on top of the plinth in the final installation location. The
angle from the top of the frequency converter to the
lifting cable should be 60°or greater.
In addition to the drawings above a spreader bar is an
acceptable way to lift the F enclosures.
How to Install VLT®Automation Drive FC 300 Operating Instructions
10 MG33U402 - Rev. 2013-12-16
33

3.1.5 Mechanical Dimensions
IP21 AND IP54 / UL AND NEMA TYPE 1 AND 12
AB
C
120
(4.7)
177.0
(7.0)
354.0 (13.9)
1166
(45.9)
310 (12.2)
163
(6.4)
420
(16.5)
981
(38.6)
74 (2.9)
417 (16.4)
380 (15.0)
D1
D2
130BA443.11
417
(16.4)
380
(15.0)
225 (8.9)
225
(8.9)
225.0
(8.9)
225.0 (8.9)
369.0
(14.5)
849
(33.4)
1209
(47.6)
160.0
(6.3)
160.0
(6.3)
160.0
(6.3)
160.0
(6.3)
304
(12.0)
304
(12.0)
25
(1.0)
25
(1.0)
1154
(45.4)
1362
(53.6)
420
(16.5)
157 (6.2)
72
(2.8)
1547
(60.9) 1589
(62.6)
423
(16.6)
120
(4.7)
1535
(60.4)
184.5
(7.3)
977
(38.5)
* Please note airflow directions
How to Install VLT®Automation Drive FC 300 Operating Instructions
MG33U402 - Rev. 2013-12-16 11
33

AB
C
IP00 / CHASSIS
IP00/IP21/IP54 - ALL SIZES
1099
43.3( )
1280
50.4( )
1327
52.2
()
375
14.8( )
417
16.4( )
298
11.7( )304
12.0( )
120
4.7( )
977
38.5( )
160
6.3( )
185
7.3( )
369
14.5( )
1282
50.5( )
25
1.0( )
161
6.3( )
225
(8.9)
225
(8.9)
997
39.3( )
818
32.2( )
408
16.1( )
66
2.6( )
408
16.1( )
66
2.6( )
298
11.7
( )
375
14.8( )
1046
41.2( )
120
4.7( )
696
27.4( )
160
6.3( )
1001
25
1.0( )
39.4( )
304
12.0( )
151
5.9( )
157
6.2( )
147
5.8( )
417
16.4( )
177
7.0( )
354
13.9( )
25
1.0( )
22
0.9
( )
49
1.9( )
25
1.0( )
Ø 11
.4( )
20.0
0.8
( )
10
0.4
( )
51
2.0( )
11
0.4( )
160.0
6.30( )
160.0
6.30( )
225.0
8.9( )
225.0
8.9( )
D3 D4
BA C
22
0.9
( )
138BA442.10
* Please note airflow directions
How to Install VLT®Automation Drive FC 300 Operating Instructions
12 MG33U402 - Rev. 2013-12-16
33

E1
225
8.86( )
1551
61.1( )
2000
(78.74)
727
28.6( )
72
2.8( )
164
600
(23.62) 198
7.8( )
145
5.7( )
494
19.4( )
392
15.4( )
538
21.2( )
160
6.3( )
1043
41.1( )
160
6.3( )
72
2.8( )
27
1.1( )
23
0.9( )
185
7.3( )
185
7.3( )
58
2.3( )
484
19.1
()
2X 13
0.5
( )
25
1.0
()
56
2.2( )
6.5( )
185
7.3( )
1.0( )
F
F
130BA444.10
SIDE CABLE ENTRY KNOCK-OFF PLATE
CABLE BASE BOTTOM CABLE ENTRY
IP21 AND IP54 / UL AND NEMA TYPE 1 AND 12
Ø 25
* Please note airflow directions
How to Install VLT®Automation Drive FC 300 Operating Instructions
MG33U402 - Rev. 2013-12-16 13
33

130BA445.10
225
64
1320
585
269
156
23
25
498
539
1547 1502
160
1043
14
184 184
184
139 304
2X13
(2.5)
(23.0)
(52.0)
(6.2)
(19.5)
(10.6)
(21.2)
(60.9)
(5.5) (12.0)
(7.3) (7.3)
(0.5)
(1.5)
120
(4.7)
25
(1.0)
(59.1)
(41.1)
(6.3)
(8.9)
225
(8.9)
(1.0) 25
(1.0)
(0.9)
27
(1.0)
13
(0.5)
E2
D
E
D
E
IP00 / CHASSIS
* Please note airflow directions
How to Install VLT®Automation Drive FC 300 Operating Instructions
14 MG33U402 - Rev. 2013-12-16
33

F1 IP21/54 - NEMA 1/12 F3 IP21/54 - NEMA 1/12
1
130BB027.10
2281.4
(89.82)
2206.4
(86.87)
1499.2
(59.02)
1400.0
(55.12) ø29.0
(1.14)
225.0
(8.85)
607.0
(23.9)
225.0
(8.85)
1
130BB029.10
2280
(89.7)
2205
(86.8)
1497
(58.9)
1997
(78.6) ø29
( 1.1)
607
(23.9)
1) Minimum clearance from ceiling
How to Install VLT®Automation Drive FC 300 Operating Instructions
MG33U402 - Rev. 2013-12-16 15
33

F2 IP21/54 - NEMA 1/12 F4 IP21/54 - NEMA 1/12
225.0
(8.85)
2281
(89.8)
1499
(59.0)
Ø29
(1.1)
1804
(71.0)
2206
(86.9)
606
(23.8)
130BB028.10
1
1
130BB030.10
2280
(89.7)
2205
(86.8)
1497 (58.9)
2401
(94.5) Ø29
(1.1)
225.0
(8.85)
604
(23.8)
1) Minimum clearance from ceiling
How to Install VLT®Automation Drive FC 300 Operating Instructions
16 MG33U402 - Rev. 2013-12-16
33

Frame size D1 D2 D3 D4
90-110 kW
(380-500 V)
37-132 kW
(525-690 V)
132-200 kW
(380-500 V)
160-315 kW
(525-690 V)
90-110 kW
(380-500 V)
37-132 kW
(525-690 V)
132-200 kW
(380-500 V)
160-315 kW
(525-690 V)
IP
NEMA 21
Type 1 54 Type 12 21 Type 1 54 Type 12 00 Chassis 00 Chassis
Shipping dimensions Height 650 650 650 650 650 650
Width 1730 1730 1730 1730 1220 1490
Depth 570 570 570 570 570 570
Frequency converter
dimensions Height 1209 1209 1589 1589 1046 1327
Width 420 420 420 420 408 408
Depth 380 380 380 380 375 375
Max
weight
[kg] 104 104 151 151 91 138
Table 3.1 Mechanical dimensions [mm], frame size D
Frame size E1 E2 F1 F2 F3 F4
250-400 kW
(380-500 V)
355-560 kW
(525-690 V)
250-400 kW
(380-500 V)
355-560 kW
(525-690 V)
450-630 kW
(380-500 V)
630-800 kW
(525-690 V)
710-800 kW
(380-500 V)
900-1200 kW
(525-690 V)
450-630 kW
(380-500 V)
630-800 kW
(525-690 V)
710-800 kW
(380-500 V)
900-1200 kW
(525-690 V)
IP
NEMA 21, 54
Type 12 00 Chassis 21, 54 Type 12 21, 54 Type 12 21, 54 Type 12 21, 54 Type 12
Shipping
dimensions Height 840 831 2324 2324 2324 2324
Width 2197 1705 1569 1962 2159 2559
Depth 736 736 1130 1130 1130 1130
Frequency
converter
dimensions Height 2000 1547 2204 2204 2204 2204
Width 600 585 1400 1800 2000 2400
Depth 494 498 606 606 606 606
Max
weight 313 277 1004 1246 1299 1541
Table 3.2 Mechanical dimensions [mm], frame sizes E and F
How to Install VLT®Automation Drive FC 300 Operating Instructions
MG33U402 - Rev. 2013-12-16 17
33

3.1.6 Rated Power
Frame size D1 D2 D3 D4
130BA816.10
130BA817.10
130BA819.10
130BA820.10
Enclosure
protection
IP 21/54 21/54 00 00
NEMA Type 1/Type 12 Type 1/Type 12 Chassis Chassis
High overload rated
power - 160%
overload torque
90-110 kW at 400 V
(380-500 V)
37-132 kW at 690 V
(525-690 V)
132-200 kW at 400 V
(380-500 )
160-315 kW at 690 V
(525-690 V)
90-110 kW at 400 V
(380-500 V)
37-132 kW at 690 V
(525-690 V)
132-200 kW at 400 V
(380-500 V)
160-315 kW at 690 V
(525-690 V)
Table 3.3 Rated Power, Enclosure Type D
Frame size E1 E2 F1/F3 F2/F4
130BA818.10
130BA821.10
F3 F1
130BA959.10
F4 F2
130BB092.11
Enclosure
protection
IP 21/54 00 21/54 21/54
NEM
AType 1/Type 12 Chassis Type 1/Type 12 Type 1/Type 12
High overload
rated power -
160% overload
torque
250-400 kW at 400 V
(380-500 V)
355-560 kW at 690 V
(525-690 V)
240-400 kW at 400 V
(380-500 V)
355-560 kW at 690 V
(525-690 V)
450-630 kW at 400 V
(380-500 V)
630-800 kW at 690 V
(525-690 V)
710-800 kW at 400 V
(380-500 V)
900-1200 kW at 690 V
(525-690 V)
Table 3.4 Rated Power, Enclosure Types E and F
NOTICE
The F enclsoures have 4 different sizes, F1, F2, F3 and F4. The F1 and F2 consist of an inverter cabinet on the right and
rectifier cabinet on the left. The F3 and F4 have an additional options cabinet left of the rectifier cabinet. The F3 is an
F1 with an additional options cabinet. The F4 is an F2 with an additional options cabinet.
How to Install VLT®Automation Drive FC 300 Operating Instructions
18 MG33U402 - Rev. 2013-12-16
33