Danfoss AK-LM 350 Guide

Monitoring unit with
COP calculation
AK-LM 350
Design Guide
ADAP-KOOL®Refrigeration control systems

2 RS8GX102 © Danfoss 10-2013 AK-LM 350
Contents
1. Introduction.............................................................................3
Application.................................................................................................. 3
Principles...................................................................................................... 4
2. Design of a controller..............................................................7
Module survey ........................................................................................... 8
Common data for modules.................................................................10
Controller ...........................................................................................12
Extension module AK-XM 101A.................................................14
Extension module AK-XM 102A / AK-XM 102B.....................16
Extension module AK-XM 204A / AK-XM 204B.....................18
Extension module AK-XM 205A / AK-XM 205B.....................20
Extension module AK-XM 107A.................................................22
Extension module AK-OB 101A..................................................24
Transformer module AK-PS 075 / 150......................................25
Communication module AK-CM 102.......................................26
Preface to design ....................................................................................28
Functions............................................................................................28
Connections......................................................................................29
Limitations.........................................................................................29
Design of a monitoring.........................................................................30
Procedure:..........................................................................................30
Sketch..................................................................................................30
Monitoring unit................................................................................31
Connections......................................................................................32
Planning table ..................................................................................33
Length.................................................................................................34
Linking of modules.........................................................................34
Determine the connection points ............................................35
Connection diagram......................................................................36
Supply voltage .................................................................................37
Ordering.....................................................................................................38
3. Mounting and wiring.............................................................39
Mounting...................................................................................................40
Mounting of extension module on the basic module.......40
Wiring..........................................................................................................41
4. Conguration and operation................................................43
Conguration...........................................................................................45
Connect PC........................................................................................45
Authorization....................................................................................46
Unlock the conguration of the controllers..........................47
System setup ....................................................................................48
Set plant type ...................................................................................49
Utility meters ....................................................................................50
Thermostat functions ....................................................................51
Pressostat functions.......................................................................51
Voltage controls...............................................................................52
Digitale alarms .................................................................................52
COP calculation................................................................................53
Conguration of inputs and outputs.......................................54
Set alarm priorities..........................................................................56
Check of settings.....................................................................................58
Lock conguration..........................................................................61
Check conguration.......................................................................62
Check of connections ....................................................................63
Installation in network..........................................................................64
First start of control................................................................................65
Start the control...............................................................................66
Setup logs..........................................................................................67
5. Regulating functions.............................................................69
Monitoring functions ............................................................................70
Miscellaneous ..........................................................................................73
Alarm texts................................................................................................75
6. Appendix, COP signals ..........................................................76
CO2Booster..............................................................................................76
CO2Booster HR .......................................................................................76
CO2Booster HR Brine............................................................................76
Cascade ......................................................................................................77
Single stage...............................................................................................77

AK-LM 350 RS8GX102 © Danfoss 10-2013 3
Application
AK-LM 350 is a complete monitoring unit with the option of regu-
lation functions via relay switches.
The monitoring unit is used to detect temperature, pressure,
functions etc. in and around appliance cases and cold rooms for
commercial and industrial cooling.
COP calculation can be made on the following systems:
• CO2booster
• CO2booster with heat recovery
• CO2booster with heat recovery and brine
• Cascade plant
• Single stage
The monitoring unit is equipped with data communication and is
operated via a PC.
Functions
Temperature
• Temperature detection
• Temperature monitoring with alarm function
• Extension of the alarm delay when a defrost signal (DI) is re-
ceived
• Interruption of alarm monitoring when a switch signal (DI) is
received
• Temperature control with relay function
Pressure
• Pressure detection
• Pressure monitoring with alarm function
• Pressure control with relay function
Voltages of 0-10 V
• Voltage detection
• Voltage monitoring with alarm function
• Voltage monitoring with relay function
On/O signals
• Detection of switch signals
• Alarm function with delay + relay function, if applicable
• The switch signal can be inverted
• Hour counter for On time
• Counter for number of changes
Pulse signals
• Registration of electricity, water, gas, etc.
• Energy reading
• Energy reading in a set synchronisation period
• Energy reading in a period between synchronisation pulses
• Receiving synchronisation signal
COP calculation
• COP for MT and LT
• Etais for MT and LT
• Refrigeration capacity for MT and LT
• Heat recovery
• Heat loos
• COSP for the whole system
1. Introduction
Alarm relay
• Two alarm relays that are enabled on dierent alarm priorities
Data communication
• Connection to system manager or gateway
• Monitoring and data collection
• Customised alarm texts
The COP calculation requires a 0-10 V signal that indicates how
much of the compressor capacity is connected.
This signal can be retrieved from the compressor controller, if it is
one of the following types:
AK-PC 772
AK-PC 781, version 4 or newer (version 4 = January 2013)
AK-PC 783.
The same reading can be used by several dierent
functions.
Up to 120 inputs and outputs are permitted.
40
20
20
20
8

4 RS8GX102 © Danfoss 10-2013 AK-LM 350
Principles
The great advantage of this series of controllers is that it can
be extended as the size of the plant is increased. It has been
developed for refrigeration control systems, but not for any
specic application – variation is created through the read-in
software and the way you choose to dene the connections.
It is the same modules that are used for each regulation and the
composition can be changed, as required. With these modules
(building blocks) it is possible to create a multitude of various
kinds of regulations. But it is you who must help adjusting the
regulation to the actual needs – these instructions will assist you
to nd your way through all the questions so that the regulation
can be dened and the connections made.
Advantages
• The controller’s size can “grow” as systems grow
• The software can be set for one or more regulations
• Several regulations with the same components
• Extension-friendly when systems requirements are changed
• Flexible concept:
- Controller series with common construction
- One principle – many regulation uses
- modules are selected for the actual connection requirements
- The same modules are used from regulation to regulation
Controller
Top part
Extension modules
A regulation with few connections can
be performed with the controller module
alone
If there are many connections one or more
extension modules have to be mounted
If the system grows and more functions have to be controlled, the regulation can be
extended.
With extra modules more signals can be received and more relays cut in and out
– how many of them – and which – is determined by the relevant application.
Bottom part
The controller is the cornerstone of the regulation. The module has inputs and
outputs capable of handling small systems.
• The bottom part – and hence the terminals – are the same for all controller types.
• The top part contains the intelligence with software. This unit will vary according
to controller type. But it will always be supplied together with the bottom part.
• In addition to the software the top part is provided with connections for data
communication and address setting.
Examples

AK-LM 350 RS8GX102 © Danfoss 10-2013 5
Direct connection
Setup and operation of an AK controller must be accomplished via
the “AK-Service Tool” software program.
The programme is installed on a PC, and setup and operation of
the various functions are carried out via the controller’s menu
displays.
Displays
The menu displays are dynamic, so that dierent settings in one
menu will result in dierent setting possibilities in other menus.
A simple application with few connections will give a setup with
few settings.
A corresponding application with many connections will give a
setup with many settings.
From the overview display there is access to further displays for
the compressor regulation and the condenser regulation.
At the bottom of the display there is access to a number of general
functions, such as “overview”, “manual operation”, “log function”,
“alarms”, and “service” (conguration).
Network linking
The controller can be linked up into a network together with other
controllers in an ADAP-KOOL® refrigeration control system.
A gateway type AKA 245, or a system manager type AK-SM 350,
AK-SM 720 or AK-SC 355, can be used as a system unit.
After the setup operation can be performed at a distance with,
say, our software program type AKM.
Users
The controller comes supplied with several languages, one of
which can be selected and employed by the user. If there are
several users, they may each have their choice of language. All
users must be assigned a user prole which either gives access to
full operation or gradually limits the operation to the lowest level
that only allows you“to see”.

6 RS8GX102 © Danfoss 10-2013 AK-LM 350
■Power
■Comm
■DO1 ■Status
■DO2 ■Service Tool
■DO3 ■LON
■DO4 ■I/O Extension
■DO5 ■Alarm
■DO6
■DO7
■DO8 ■Service Pin
Light-emitting diodes
A number of light-emitting diodes makes it possible to follow the
signals that are received and transmitted by the controller.
Log
From the log function you can dene the measurements you wish
to be shown.
The collected values can be printed, or you may export them to a
le. You can open the le in Excel or import in AKM.
(The log function is only available via AK-ST 500.)
A log should usually be created on the system unit. The system
unit has a larger memory and can contain more data.
If you are in a service situation you can show measurements in a
trend function. The measurements are then made real-time and
displayed instantly.
Alarm
The display gives you an overview of all active alarms. If you wish
to conrm that you have seen the alarm you can cross it o in the
acknowledge eld.
If you want to know more about a current alarm you can click on it
and obtain an information display on the screen.
A corresponding display exists for all earlier alarms. Here you can
upload information if you need further details about the alarm
history.
Slow ash = OK
Quick ash = answer from gateway
Constantly ON = error
Constantly OFF = error
Flash = active alarm/not cancelled
Constant ON = Active alarm/cancelled

AK-LM 350 RS8GX102 © Danfoss 10-2013 7
2. Design of a controller
This section describes how the monitoring unit is designed.
The controller in the system is based on a uniform connection
platform where any deviations from regulation to regulation is
determined by the used top part with a specic software and
by which input and output signals the relevant application will
require. If it is an application with few connections, the controller
module (top part with belonging bottom part) may be sucient.
If it is an application with many connections it will be necessary to
use the controller module plus one or more extension modules.
This section will give you a survey of possible connections plus
assistance in selecting the modules required by your actual
application.

8 RS8GX102 © Danfoss 10-2013 AK-LM 350
Module survey
• Controller module – capable of handling minor plant require-
ments.
• Extension modules. When the complexity becomes greater
and additional inputs or outputs are required, modules can be
attached to the controller. A plug on the side of the module will
transmit the supply voltage and data communication between
the modules.
• Top part
The upper part of the controller module contains the
intelligence. This is the unit where the regulation is dened and
where data communication is connected to other controllers in a
bigger network.
• Connection types
There are various types of inputs and outputs. One type may, for
example, receive signals from sensors and switches, another may
receive a voltage signal, and a third type may be outputs with
relays etc. The individual types are shown in the table below.
• Optional connection
When a regulation is planned (set up) it will generate a need for
a number of connections distributed on the mentioned types.
This connection must then be made on either the controller
module or an extension module. The only thing to be observed
is that the types must not be mixed (an analog input signal must
for instance not be connected to a digital input).
• Programming of connections
The controller must know where you connect the individual
input and output signals. This takes place in a later conguration
where each individual connection is dened based on the
following principle:
- to which module
- at which point (”terminals”)
- what is connected (e.g. pressure transmitter/type/
pressure range)
Top part
Extension module with
additional analog inputs
Extension module with additional
relay outputs and additional
analog inputs.
The module with additional relay outputs is
also available in a version where the top part
is provided with change-over switches so
that the relays can be overridden.
Controller with analog inputs and
relay outputs.
Bottem part

AK-LM 350 RS8GX102 © Danfoss 10-2013 9
Type Analog
inputs
On/O outputs On/o supply voltage
(DI signal)
Module with
switches
For sensors, pres-
sure transmitters
etc.
Relay
(SPDT)
Solid state Low voltage
(max. 80 V)
High voltage
(max. 260 V)
Pulse counter
Low voltage
(max 30 V)
For override of
relay outputs
Controller 11 4 4 - - - -
Extension modules
AK-XM 101A 8
AK-XM 102A 8
AK-XM 102B 8
AK-XM 204A 8
AK-XM 204B 8 x
AK-XM 205A 8 8
AK-XM 205B 8 8 x
AK-XM 107A 4 (8)
Type Function Application
Operation
AK-ST 500 Software for operation of AK controllers AK-operation
- Cable between PC and AK controller AK - Com port
-Cable between zero modem cable and AK controller /
Cable between PDA cable and AK controller AK - RS 232
- Cable between PC and AK controller AK - USB
Accessories Transformer module 230 V / 115 V to 24 V
AK-PS 075 18 VA, 24 V d.c.
Supply for controller
AK-PS 150 36 VA, 24 V d.c.
Accessories Real time clock for use in controllers that require a clock function, but are not wired with data communication.
AK-OB 101A Real time clock with battery backup. To be mounted in an AK controller
Accessories Communication modules for controllers where modules cannot be connected continuously
AK-CM 102 Communication module Data communication for external extension modules
Type Function Application
AK-LM 350 Monitoring unit with COP calculation Monitoring of temperatures, pressure, voltage etc.
1. Controller
2. Extension modules and survey of inputs and outputs
3. AK operation and accessories
On the following pages there is data specic to each module.

10 RS8GX102 © Danfoss 10-2013 AK-LM 350
Common data for modules
Supply voltage 24 V d.c./a.c. +/- 20%
Power consumption AK-__ (controller) 8 VA
AK-XM 101, 102, 107 2 VA
AK-XM 204, 205 5 VA
Analog inputs Pt 1000 ohm /0°C Resolution: 0.1°C
Accuracy: +/- 0.5°C (between -50°C and +50°C)
Pressure transmitter type AKS 32R / AKS
2050/ AKS 32 (1-5 V)
Resolution:1 mV
Accuracy +/- 10 mV
Max. connection of 5 pressure transmitters on one module
Other pressure transmitter:
Ratiometric signal
Min. and max. pressure must be set
Min and max. voltage must be set
Voltage signal 0-10 V
Contact function (On/O ) On at R < 20 ohm
O at R > 2K ohm
(Gold -plated contacts not necessary)
On/o supply voltage inputs Low voltage
0 / 80 V a.c./d.c.
O: U < 2 V
On: U > 10 V
High voltage
0 / 260 V a.c.
O: U < 24 V
On: U > 80 V
Relay outputs
SPDT
AC-1 (ohmic) 4 A
AC-15 (inductive) 3 A
UMin. 24 V
Max. 230 V
Low and high voltage must not be connected to the same
output group
Solid state outputs Can be used for loads that are cut in and
out frequently, e.g. :
rail heat, fans and AKV valve
Max. 240 V a.c. , Min. 48 V a.c.
Max. 0.5 A,
Leak < 1 mA
Max. 1 AKV
Ambient temperature During transport -40 to 70°C
During operation -20 to 55°C ,
0 to 95% RH (non condensing)
No shock inuences / vibrations
Enclosure Material PC / ABS
Density IP10 , VBG 4
Mounting For mounting on panel wall or DIN rail
Weight with screw terminals Modules in100- / 200- / controller-series Ca. 200 g / 500 g / 600 g
Approvals EU low voltage directive and EMC require-
ments are complied with
LVD tested according to EN 60730
EMC tested
Immunity according to EN 61000-6-2
Emission according to EN 61000-6-3
UL 873, UL le number: E166834 for XM modules
UL le number: E31024 for LM modules
The mentioned data applies to all modules.
If data is specic, this is mentioned together with the module in question.

AK-LM 350 RS8GX102 © Danfoss 10-2013 11
Dimensions
The module dimension is 72 mm.
Modules in the 100-series consist of one
module
Modules in the 200-series consist of two
modules
Controllers consist of three modules
The length of an aggregate unit = n x 72 + 8

12 RS8GX102 © Danfoss 10-2013 AK-LM 350
Controller
Function
There are several controllers in the series. The function is
determined by the programmed software, but outwardly the
controllers are identical – they all have the same connection
possibilities:
11 analog inputs for sensors, pressure transmitters, voltage signals
and contact signals.
8 digital outputs, with 4 Solid state outputs and 4 relay outputs
Supply voltage
24 V a.c. or d.c. to be connected to the controller.
The 24 V must not be retransmitted and used by other controllers
as it is not galvanically separated from inputs and outputs. In
other words, you must use a transformer for each controller. Class
II is required. The terminals must not be earthed.
The supply voltage to any extension modules is transmitted via
the plug on the right-hand side.
The size of the transformer is determined by the power
requirement of the total number of modules.
The supply voltage to a pressure transmitter can be taken either
from the 5 V output or from the 12 V output depending on
transmitter type.
Data communication
If the controller is to be included in a system, communication
must take place via the LON connection.
The installation has to be made as mentioned in the separate
instructions for LON communication.
Address setting
When the controller is connected to a gateway type AKA 245,
the controller’s address must be set between 1 and 119. (If it is a
system manager AK-SM .., then 1-200).
Service PIN
When the controller is connected to the data communication
cable the gateway must have knowledge of the new controller.
This is obtained by pushing the key PIN. The LED“Status”will ash
when the gateway sends an acceptance message.
Operation
The conguration operation of the controller must take place from
the software programme“Service Tool”. The program must be
installed on a PC, and the PC must be connected to the controller
via the network plug on the front of the unit.
Light-emitting diodes
There are two rows with LED’s. They mean:
Left row:
• Voltage supply to the controller
• Communication active with the bottom PC board (red = error)
• Status of outputs DO1 to DO8
Right row:
• Software status (slow ash = OK)
• Communication with Service Tool
• Communication on LON
• Communication with AK-CM 102
• Alarm when LED ashes
- 2 LED’s that are not used
• “Service Pin” switch has been activated
■Power
■Comm
■DO1 ■Status
■DO2 ■Service Tool
■DO3 ■LON
■DO4 ■I/O Extension
■DO5 ■Alarm
■DO6
■DO7
■DO8 ■Service Pin
PIN
Address
Keep the safety
distance!
Low and high
voltage must not
be connected to
the same output
group
Slow ash = OK
Quick ash = answer from gateway
Constantly ON = error
Constantly OFF = error
Flash = active alarm/not cancelled
Constant ON = Active alarm/cancelled

AK-LM 350 RS8GX102 © Danfoss 10-2013 13
Point
Signal Signal
type
S
Pt 1000 ohm/0°C
S... Pt 1000
P
AKS 32R
AKS 32
P...
AKS 32R
-1 - xx bar
AKS 32
-1 - zz bar
U
Volt
input...
0 - 5 V
0 - 10 V
On/O Active at:
Closed
/
Open
DO Active at:
On
/
O
Signal Module Point Terminal Signal type /
Active at
1
1(AI 1) 1 - 2
2(AI 2) 3 - 4
3(AI 3) 5 - 6
4(AI 4) 7 - 8
5(AI 5) 9 - 10
6(AI 6) 11 - 12
7(AI 7) 13 - 14
8(AI 8) 19 - 20
9(AI 9) 21 - 22
10 (AI 10) 23 - 24
11 (AI 11) 25 - 26
12 (DO 1) 31 - 32
13 (DO 2) 33 - 34
14 (DO 3) 35 - 36
15 (DO 4) 37 - 38
16 (DO 5) 39 - 40- 41
17 (DO6) 42 - 43 - 44
18 (DO7) 45 - 46 - 47
19 (DO8) 48 - 49 - 50
Terminal 15: 12 V
Terminal 16: 5 V
Terminal 27: 12 V
Terminal 28: 5 V
Terminal
17, 18, 29, 30:
(Cable screen)
Solid state outputs
on 12 - 15
Relay or AKV coil
fx 230 V a.c.
Relay outputs on
16 - 19
Analog
inputs
on 1 - 11
Point 1 2 3 4 5 6 7 8 9 10 11
Type AI1 AI2 AI3 AI4 AI5 AI6 AI7 AI8 AI9 AI10 AI11
Point 12 13 14 15 16 17 18 19
Type DO1 DO2 DO3 DO4 DO5 DO6 DO7 DO8
24 and 25 not
used at monitor-
ing
3: Brown
2: Blue
1: Black
3: Brown
2: Black
1: Red
AKV

14 RS8GX102 © Danfoss 10-2013 AK-LM 350
Extension module AK-XM 101A
Function
The module contains 8 analog inputs for sensors, pressure
transmitters, voltage signals and contact signals.
Supply voltage
The supply voltage to the module comes from the previous
module in the row.
Supply voltage to a pressure transmitter can be taken from either
the 5 V output or the 12 V output depending on transmitter type.
Light-emitting diodes
Only the two top LED’s are used. They indicate the following:
• Voltage supply to the module
• Communication with the controller is active (red = error)

AK-LM 350 RS8GX102 © Danfoss 10-2013 15
Signal Module Point Terminal Signal type /
Active at
1(AI 1) 1 - 2
2(AI 2) 3 - 4
3(AI 3) 5 - 6
4(AI 4) 7 - 8
5(AI 5) 17 - 18
6(AI 6) 19 - 20
7(AI 7) 21 - 22
8(AI 8) 23 - 24
Point
Signal Signal
type
S
Pt 1000 ohm/0°C
S... Pt 1000
P
AKS 32R
AKS 2050
AKS 32
P...
AKS 32R
AKs 2050
-1 - xx bar
AKS 32
-1 - zz bar
U
V... 0 - 5 V
0 - 10 V
On/O Day/
Night
Door
Defrost
Active at:
Closed
/
Open
Point 5 6 7 8
Type AI5 AI6 AI7 AI8
Point 1 2 3 4
Type AI1 AI2 AI3 AI4
Terminal 9: 12 V
Terminal 10: 5 V
Terminal 15: 5 V
Terminal 16: 12 V
Terminal
11, 12, 13, 14:
(Cable screen)
At the top the
signal input is
the left of the
two terminals.
At the bottom
the signal input
is the right of the
two terminals.
3: Brown
2: Blue
1: Black
3: Brown
2: Black
1: Red

16 RS8GX102 © Danfoss 10-2013 AK-LM 350
Extension module AK-XM 102A / AK-XM 102B
AK-XM 102B
Max. 230 V
On/O:
On: DI > 80 V a.c.
O: DI < 24 V a.c.
AK-XM 102A
Max. 24 V
On/O:
On: DI > 10 V a.c.
O: DI < 2 V a.c.
Function
The module contains 8 inputs for on/o voltage signals.
Signal
AK-XM 102A is for low voltage signals.
AK-XM 102B is for high voltage signals.
Supply voltage
The supply voltage to the module comes from the previous
module in the row.
Light-emitting diodes
They indicate:
• Voltage supply to the module
• Communication with the controller is active (red = error)
• Status of the individual inputs 1 to 8 (when lit = voltage)

AK-LM 350 RS8GX102 © Danfoss 10-2013 17
Signal Module Point Terminal Active at
1(DI 1) 1 - 2
2(DI 2) 3 - 4
3(DI 3) 5 - 6
4(DI 4) 7 - 8
5(DI 5) 9 - 10
6(DI 6) 11 - 12
7(DI 7) 13 - 14
8(DI 8) 15 - 16
Point
Signal Active at
DI
Day/
Night
Door.
Defrost
Closed
(voltage on)
/
Open
(voltage o)
Point 5 6 7 8
Type DI5 DI6 DI7 DI8
Point 1 2 3 4
Type DI1 DI2 DI3 DI4
AK-XM 102A: Max. 24 V
AK-XM 102B: Max. 230 V

18 RS8GX102 © Danfoss 10-2013 AK-LM 350
Extension module AK-XM 204A / AK-XM 204B
AK-XM 204A AK-XM 204B
Max. 230 V
AC-1: max. 4 A (ohmic)
AC-15: max. 3 A (Inductive)
Function
The module contains 8 relay outputs.
Supply voltage
The supply voltage to the module comes from the previous
module in the row.
AK-XM 204B only
Override of relay
Eight change-over switches at the front make it possible to
override the relay’s function.
Either to position OFF or ON.
In position Auto the controller carries out the control.
Light-emitting diodes
There are two rows with LED’s. They indicate the following:
Left row:
• Voltage supply to the controller
• Communication active with the bottom PC board (red = error)
• Status of outputs DO1 to DO8
Right row: (AK-XM 204B only):
• Override of relays
ON = override
OFF = no override
Fuses
Behind the upper part there is a fuse for each output.
Keep the safety distance!
Low and high voltage
must not be connected to
the same output group
AK-XM 204B
Override of relay

AK-LM 350 RS8GX102 © Danfoss 10-2013 19
Point
Signal Module Point Terminal Active at
1(DO 1) 25 - 26 - 27
2(DO 2) 28 - 29 - 30
3(DO 3) 31 - 32 - 33
4(DO 4) 34 - 35 -36
5(DO 5) 37 - 38 - 39
6(DO 6) 40 - 41 - 42
7(DO 7) 43 - 44 - 45
8(DO 8) 46 - 47 - 48
Signal Active at
DO Fan
Alarm
Light
Rail-heat
Defrost
Night
blinds
Valves
Compres-
sor
On
/
O
Point 1 2 3 4 5 6 7 8
Type DO1 DO2 DO3 DO4 DO5 DO6 DO7 DO8

20 RS8GX102 © Danfoss 10-2013 AK-LM 350
Extension module AK-XM 205A / AK-XM 205B
max. 10 V
AK-XM 205A AK-XM 205B
Max. 230 V
AC-1: max. 4 A (ohmic)
AC-15: max. 3 A (Inductive)
Function
The module contains:
8 analog inputs for sensors, pressure transmitters, voltage signals
and contact signals.
8 relay outputs.
Supply voltage
The supply voltage to the module comes from the previous
module in the row.
AK-XM 205B only
Override of relay
Eight change-over switches at the front make it possible to
override the relay’s function.
Either to position OFF or ON.
In position Auto the controller carries out the control.
Light-emitting diodes
There are two rows with LED’s. They mean:
Left row:
• Voltage supply to the controller
• Communication active with the bottom PC board (red = error)
• Status of outputs DO1 to DO8
Right row: (AK-XM 205B only):
• Override of relays
ON = override
OFF = no override
Fuses
Behind the upper part there is a fuse for each output.
Keep the safety distance!
Low and high voltage
must not be connected to
the same output group
AK-XM 205B
Override of relay