Danfoss SonoSelect 10 Operation manual

1
03/2017 © Danfoss VUIGB602
www.heating.danfoss.com
Installation & User Guide
SonoSelect and SonoSafe
energy meters

2 | © Danfoss | Energy Meters | 2017.03 VUIGB702
Installation & User Guide SonoSelect and SonoSafe
Note! To ensure latest version of declaration, please visit danfoss.com.

VUIGB702 © Danfoss | Energy Meters | 2017.03 | 3
Installation & User Guide SonoSelect and SonoSafe
Contents
1. Inside the box ........................................................................... 4
2. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.1 Preparation...........................................................................4
2.2 Identification of installation: Supply/Return pipe installation ...........................5
2.3 Flow sensor installation...............................................................5
2.4 Mounting orientation, calculator ......................................................5
2.5 Mounting of O-ring and temperature sensor ..........................................6
2.6 Communication (Expansion modules).................................................7
2.7 Installation of module/cable ........................................................ 10
2.8 Battery ..............................................................................11
3. Commissioning ......................................................................... 12
3.1 Bleeding ........................................................................... 12
3.2 Supply/return configuration .........................................................12
3.3 Meter sealing....................................................................... 12
3.4 IP class ............................................................................. 12
4. Function overview ...................................................................... 13
4.1 Menu structure ..................................................................... 13
4.2 Display explanation..................................................................14
4.3 Alarms ..............................................................................14
5. Device overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
6. Disposal................................................................................ 15

4 | © Danfoss | Energy Meters | 2017.03 VUIGB702
Installation & User Guide SonoSelect and SonoSafe
1. Inside the box
Description of components included in the box
107/2015 ©Danfoss VDIGH102
InstallationGuide
SonoSelect and SonoSafe
energy meters
1 x
Energy meter
2 x
Gaskets
1 x
Temperature sensor
O-ring and mounting pin
4 x
Wired seals
1 x
Installation
& User Guide
Note!
• For cooling meters a wall mounting kit is delivered with the product
2. Installation
2.1 Preparation
SonoSelect incorporates a tamper monitor-
ing function. If the calculator is opened the
meter will set alarm E13 in display.
Don’t open unless for adding communica-
tion module, replacing battery or installing
cables.
Reset requires Bluetooth dongle 014U1963
and SonoApp service tool.
SonoSelect is delivered with the option
of reconfiguring supply/return using the
Bluetooth dongle 014U1963 and SonoApp
service tool.
Note!
• Product is approved for ambient temperature between 5-55 °C, non-condensing (indoor installation). It is
recommended to install Calculator at max. 45 °C to secure optimal conditions for battery lifetime. At media
temperatures below ambient temperature (cooling) the calculator must be mounted separately from the flow
sensor to prevent condensation.
• Avoid installation stress from pipes and fittings.
• Flush the system.

VUIGB702 © Danfoss | Energy Meters | 2017.03 | 5
Installation & User Guide SonoSelect and SonoSafe
2.2 Identification of installation: Supply/Return pipe installation
Supply installation Return installation
Heat meters have red temp sensor in supply pipe and all cooling meters have blue temp sensor in supply pipe
2.3 Flow sensor installation
Pipe position: No limitations but avoid positions
where air can be collected.
Rotation in pipe axis: Flow sensor should be angled
in 45 to 315° to avoid air collection in flow sensor.
2.4 Mounting orientation, calculator
4 x 90°
Click!
1a.
2.
3.
1b.

6 | © Danfoss | Energy Meters | 2017.03 VUIGB702
Installation & User Guide SonoSelect and SonoSafe
2.5 Mounting of O-ring and temperature sensor
One temperature sensor is factory mounted in the flow sensor. The other must be mounted in the opposite
pipe relative to the flow sensor installation.
1.
Mount O-ring
on pin.
2.
Insert pin with
O-ring.
3.
Position O-ring.
4.
Remove pin.
5.
Moist and insert sensor
probe.Tighten at torque
12 ± 2 Nm.
To ensure accuracy and a tight seal the sensor installation should comply to EN1434-2 annex A:
Key
Threaded connec-
tion size A
Tapping bore
size B
G½ 18.5 mm
G¾ 24 mm
G1 30.5 mm
Note:
Tolerance on machined dimensions = ± 0.5 mm.
Pipe fittings for use with probe type DS (Direct Short).
: provision for security sealing.

VUIGB702 © Danfoss | Energy Meters | 2017.03 | 7
Installation & User Guide SonoSelect and SonoSafe
2.6 Communication modules
Modules in general
To adapt the meter for various applications SonoSelect 10 and SonoSafe 10 features a slot for mounting
communication modules.
Each module features its own µ-controller and is powered by its own battery.
Modules have their own parameter set which is saved in the module µ-controller flash memory. A local
copy of the energy meter parameters used for communication is stored in the module.
Data from module is updated in meter every 10 minutes.
Power: Lithium Thionyl Chloride battery (half of AA size).
2 pulse inputs have common ground.
Modules are galvanically isolated from energy meter circuitry
Wired M-Bus module with 2 pulse inputs
Once installed the meter will display the icon for wired communication and pulse inputs in loop 2 of the
display.
Wired M-Bus is galvanically isolated from μC and pulse inputs.
The two pulse inputs can be programmed independently of each other (see specification for pulse input
module).
M-Bus (primary) Lithium Thionyl Chloride battery (half of AA size)
M-Bus (secondary) M-Bus supply
Baud rate supported 300, 2400, 4800, 9600
Communication protocol According to EN1434-3 & EN13757-3
Battery life time 16+1 year (from productiondate)
Wireless OMS communication module, 868.95MHz with 2 pulse inputs
Once installed the meter will display the icon for wireless communication and pulse inputs in loop 2 of the
display. The two pulse inputs can be programmed independently of each other (see specification for
pulse input module).
Standard Open Metering System (OMS) issue 4.0.2
Frequency 868.95 MHz
Antenna Internal
Transmission power 10mW (7.8 dBm); (Max 25mW; 13,9dBm)
Mode T1 mode
Encryption AES 128 bit encryption (mode 5), Parameterized Static key
Sending interval Fixed network: 15 min.
Telegram Standard telegram*
Battery life time 16+1 year (with pulse inputs off)
* See section with data telegram.

8 | © Danfoss | Energy Meters | 2017.03 VUIGB702
Installation & User Guide SonoSelect and SonoSafe
2 pulse input module
Once installed the meter will display the icon for pulse inputs in menu 2 of the display. Accumulated
volume is only readable by communication. The two pulse inputs can be programmed independently of
each other (see specification for pulse input module).
Pulse value 0.001 m³ to 1 m³ per pulse
Voltage supply ≤ 6.0 V
Source current ≤ 0.1 mA
High level input threshold ≥ 2 V
Low level input threshold ≤ 0.5 V
Pull-up resistor 100 kΩ
Pulse length ≥100 ms
Maximum frequency ≤ 5 Hz
Pulse inputs According to EN1434-2, section 7.1.5 (Classification of pulse input
devices Class IB)
Battery life time 16+1 year
* Suitable for both electronic switch and Reed contact.
Data telegram
Wired M-bus
Standard telegram:
• Accumulated energy
• Accumulated volume
• Current flow
• Current power
• Supply temperature
• Return temperature
• Difference temperature
• Enclosure temperature
• Current time
• Hour counter factory
• Hour counter OK
Wireless M-bus (OMS)
Standard telegram fixed network:
• Accumulated energy
• Accumulated volume
• Current flow
• Current power
• SupplyTemperature
• ReturnTemperature
• CurrentTime

VUIGB702 © Danfoss | Energy Meters | 2017.03 | 9
Installation & User Guide SonoSelect and SonoSafe
Terminals and cables
Communication Name Terminal No.
M-Bus Meter bus (blue or orange) 24
Meter bus (blue or orange) 25
Pulse input
Pulse input 1 + (Brown) 50
Pulse input 1 - (White) 51
Pulse input 2 + (Brown) 52
Pulse input 2 - (White) 53
Cable specification
Pulse input cables <10 m
To ensure IP protection class connecting cable outer
jackets must be Ø4.2 ± 0.1 mm
Communication cables delivered with heat meter.
Cable ends are stripped with crimped ferule. 1.0 m

10 | © Danfoss | Energy Meters | 2017.03 VUIGB702
Installation & User Guide SonoSelect and SonoSafe
2.7 Installation of module/cable
1.
Before handling module
PCB ensure relevant ESD
regulations are observed
(IEC 61340-5-1).
2.
Break wired seal for
enclosure.
3.
Cut rubber parallel to enclosure.
4.
Insert module follow-
ing guide on PCBA
cover.
Insert cable through
hole, connect cable
and fix to screw termi-
nals matching color
and terminal numbers.
Fix cable(s) to cable
relief. Outer jacket
no longer than 9 mm
from cable relief (line).
Press down.
5.
Close enclosure making sure that no cables inter-
fere with rubber sealing and other internal parts.
Click!
6.
Reset tamper alarm via Sono-
App for SonoSelect 10.
For module configuration, see
SonoApp user guide.

VUIGB702 © Danfoss | Energy Meters | 2017.03 | 11
Installation & User Guide SonoSelect and SonoSafe
2.8 Battery
1.
Before handling
module PCB ensure
relevant ESD regu-
lations are observed
(IEC 61340-5-1).
2.
Break installation
seal and open en-
closure.
3.
Disconnect battery
connector and
remove battery.
4.
Short circuit battery
connectors on PCB
using a small flat
head screwdriver.
5.
Connect new battery
to PCB.
6.
Fit battery
in enclosure.
7.
Close enclosure
making sure that no
cables interfere with
rubber sealing or
other internal parts.
8.
Confirm battery
change by pressing
the button 2 times
within 120 seconds.
Reset tamper alarm
(E13) via SonoApp
for SonoSelect 10.

12 | © Danfoss | Energy Meters | 2017.03 VUIGB702
Installation & User Guide SonoSelect and SonoSafe
3. Commissioning
3.1 Bleeding
1. Bleed the system until the flow rate display is steady.
2. Make sure no error codes are displayed.
3. Check the display for a plausible indication of flow rate and temperatures.
4. For SonoSelect: Run installation check using Bluetooth dongle 014U1963 and SonoApp service tool.
3.2 Supply/return configuration
Only available for SonoSelect: Use Bluetooth dongle 014U1963 and SonoApp service tool/Configuration
3.3 Meter sealing




Tamper monitor/
access level 1
Test seal
(verification mode)
Factory seal
3.4 IP class
Calculator IP65 (SonoSelect) / IP54 (SonoSafe)
Flow sensor IP65
Temperature sensor IP65
Note: The IP class can be compromised if cables are subjected to angled tension.

VUIGB702 © Danfoss | Energy Meters | 2017.03 | 13
Installation & User Guide SonoSelect and SonoSafe
4. Function overview
4.1 Menu structure
HoursAlarm EnergyVolume
LOOP 1
Supply temp. Display test/All on
PowerFlow
LOOP 2
Accounting date Monthly date 1 >> Monthly date 12
LOOP 3
Accumulated
Current
History log
click
click
click
Return temp.

14 | © Danfoss | Energy Meters | 2017.03 VUIGB702
Installation & User Guide SonoSelect and SonoSafe
4.2 Display explanation
Working symbol Supply/return mounted installation
Accumulated energy Alarm
Accumulated flow Service/maintenance
Total hours Battery full or low
Instant power Wired communication
Instant flow Wireless communication
Supply temperature Pulse
Return temperature Decimal emphasizer
Temperature difference Units field
4.3 Alarms
E01 System error E10 Transducer error
E02 PCB error E11 Outside measured range
E03 Battery empty (less than 1 month) E12 Negative flow
E04 Battery low voltage E13 Tamper alarm
E05 Battery low (less than 12 months) E14 High flow > qss
E06 Supply Temperature Error E15 Battery consumption too high
E07 Return Temperature Error E16 Display overflow (energy/volume)
E08 Absolute/Difference temperature outside
accumulated range E32 Communication module error
E09 Low transducer signal

VUIGB702 © Danfoss | Energy Meters | 2017.03 | 15
Installation & User Guide SonoSelect and SonoSafe
5. Device overview
1
2
3
4
5
6
7
8
9
10
11
12
13
1. Display
2. PCBA
3. Cover part (PC)
4. Battery (Lithium)
5. Enclosure connection (PC)
6. Transducer (PZT/stainless steel/PEI)
7. Spool piece (Brass)
8. Liner fixture (PPS/PEI/stainless
steel)
9. Liner (PPS)
10. Top part (PC, TPE)
11. Module (PCB)
12. Bottom part (PC)
13. Temperature sensor
6. Disposal
Item Material Disposal
Battery AA-cell Lithium/thionyl chloride 620
mg Lithium
Approved deposit for lithium
batteries
PCBA with display and com-
munication module
Coppered epoxy laminate components
soldered on, PC, TPE Electronic waste
Cables Copper with PUR or PVC jackets Cable recovery
Flow sensor
(including transducer and
liner)
Brass, stainless steel, PPS Metal recovery
Transducer PZT, stainless steel, PEI Approved deposit for PZT
Other plastic parts PC, PPS, PEI, TPE Plastic recovery

16 | © Danfoss | Energy Meters | 2016.09 VUIGB702
Danfoss A/S
Energy Meters • Ulvehavevej 61 • DK-7100 Vejle • Denmark
Phone: [phone] • Fax: [phone]
[e-mail] • www.heating.danfoss.com
Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter
its products without notice. This also applies to products already on order provided that such alterations can be made without subsequential
changes being necessary in specifications already agreed.
All trademarks in this material are property of the respective companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/S.
All rights reserved.