Data Video TLM-170FM User manual

TLM-170FM
Service Manual
Revision:V1.0 2021/12/27

Datavideo Technologies Co., Ltd.
VP-951 TLM-170FM Table of Contents
Chapter 1. System Disassembling Procedure..................................................................3
Chapter 2. System assemblyProcedure ........................................................................11
Chapter 3.RMA Parts..................................................................................... ………….19
Chapter 4.PCBA and organization collocation...............................................................23
Chapter 5.Circuit Diagram..............................................................................................24

Datavideo Technologies Co., Ltd.
Chapter 1. System Disassembling Procedure
Loosen hand-screw
Remove the bottom of the host set screw
G0911D300801φ3.0*8m/m Screw*2

Datavideo Technologies Co., Ltd.
Remove the handle cylinder
Remove 1U panel and left and right screen positioning block
Remove 1 U panel lock handle
G09220477062 Handle cylinder
G0911D501001φ5.0*10m/m Screw*2
G09200710081 Screen positioning block (left)
G09200710071 Screen positioning block (right)
G09112300813 Ø3*8mm Screw*2
Use the original removal screw M3*5m/m*6
G09420710011 1U panel
G09220477052 Handle tab (left)
G09220477042 Handle tab (right)

Datavideo Technologies Co., Ltd.
Lock the host upper screw*4
Remove the Screw
G0911D400601φ4.0*6.0m/m Screw*2
G0911D300801φ3.0*8m/m Screw*2

Datavideo Technologies Co., Ltd.
Remove host and tray module
G0911D400811 M4.0*8m/m Screw*4
VP-927 TLM-170F
GC927N0-DAT
G13307201202 Tray mechanism module

Datavideo Technologies Co., Ltd.
Remove rail guide
G13307201202 Tray mechanism module
G0911D300511φ3.0*5m/m Screw*2
G09112300613 Ø3*6mm Screw*2
G09200443051 Block
G09C00004431 Rubber

Datavideo Technologies Co., Ltd.
Remove the Guide rail tie line
Remove the base
Remove the protective sheet to the base
G09112300613 Ø3*6mm Screw*6
G09220567054 Guide rail tie line
G0911D300511φ3.0*5m/m Screw*6
G09220710072 Base
G09F00071002 Protector

Datavideo Technologies Co., Ltd.
Remove the HINGE screw retainer on left and right Hinge
Remove Left and Right Hinge Left and Right Slide Rail Brackets
Remove the rail on the slide rail bracket (back)
G09112300613 Ø3*6mm Screw*3
G09200567052 HINGE screw fixing piece
G09200710013 Spindle (right)
G09200710023 Spindle (left)
G0911D300511φ3.0*5m/m Screw*2
G09140301003 Toothed nut (K cap)*3
G0911D301011 M3.0*10m/m Screw*3

Datavideo Technologies Co., Ltd.
Remove the lower rails on the left and right brackets
Remove left and right brackets and positioning beads and positioning blocks
G09200567041 Slide rail
G0911D300631φ3.0*6m/m Screw*4
G0911D300511φ3.0*5m/m Screw*16
G09200567061
Positioning block*2
G09200567013
Positioning beads*2
G09220710081 Slide rail bracket (right)
G09220710091 Slide rail bracket (left)

Datavideo Technologies Co., Ltd.
Chapter 2. System assemblyProcedure
Left and right slide bracket lock position and positioning block
G09200567061
Positioning block*2
G09200567013
Positioning beads*2
G0911D300511φ3.0*5m/m Screw*16
G09220710081 Slide rail bracket (right)
G09220710091 Slide rail bracket (left)

Datavideo Technologies Co., Ltd.
Lock with slide rail on left and right bracket
Light locking slide rail bracket (back)
G09200567041 Slide rail
G0911D300631φ3.0*6m/m Screw*4
G09220710101
Slide bracket (back)
G0911D301011 M3.0*10m/m Screw*3
G09140301003 Toothed nut (K cap)*3

Datavideo Technologies Co., Ltd.
Locks Hinge Left and Right Sliding Rail Brackets
HINGE screws are attached to the left and right Hinge
G09200710013 Spindle (right)
G09200710023 Spindle (left)
G0911D300511φ3.0*5m/m Screw*2
G09112300613 Ø3*6mm Screw*3
G09200567052 HINGE screw fixing piece

Datavideo Technologies Co., Ltd.
Attach protective sheet to the base
Locking rail tie line bracket
G09220710072 Base
G09F00071002 Protector
G0911D300511φ3.0*5m/m Screw*6
G09112300613 Ø3*6mm Screw*6
G09220567054 Guide rail tie line

Datavideo Technologies Co., Ltd.
Lock the stopper and attach the rubber pad
Take 1 U panel lock handle
G13307201202 Tray mechanism module
G09200443051 Block
G09C00004431 Rubber
G0911D300511φ3.0*5m/m Screw*2
G09112300613 Ø3*6mm Screw*2
G09420710011 1U panel
G09220477052 Handle tab (left)
G09220477042 Handle tab (right)

Datavideo Technologies Co., Ltd.
Take the VP-927 TLM-170F to tear off the upper light curtain protective film
Remove the bottom screws and do not lose the screws
G0911D400601φ4.0*6.0m/m Screw*2

Datavideo Technologies Co., Ltd.
Lock host and tray module
Locking screws
G0911D400811 M4.0*8m/m Screw*4
G0911D300801φ3.0*8m/m Screw*2

Datavideo Technologies Co., Ltd.
Pull up the host and fold it up. Remove the upper screw of the host and lock the 1U panel.
Lock handle cylinder
G09200710081 Screen positioning block (left)
G09200710071 Screen positioning block (right)
G09112300813 Ø3*8mm Screw*2
Use the original removal screw M3*5m/m*6
G09220477062 Handle cylinder
G0911D501001φ5.0*10m/m Screw*2

Datavideo Technologies Co., Ltd.
Lock the bottom of the host with a set screw
After confirming that the host machine is moving in and out smoothly, hand-screw fixing
G0911D300801φ3.0*8m/m Screw*2

Datavideo Technologies Co., Ltd.
Chapter 3.RMA Parts RMA Parts
Model name:VP-951 TLM-170FM
Item 1
Item 2
Item 3
Description:
Ø3*6mm Screw
Description:
Ø3*8mm Screw
Description:
φ3.0*5m/m Screw
Part Number:
G09112300613
Part Number:
G09112300813
Part Number:
G0911D300511
Item 4
Item 5
Item 6
Description:
φ3.0*6m/m Screw
Description:
φ3.0*8m/m Screw
Description:
M3.0*10m/m Screw
Part Number:
G0911D300631
Part Number:
G0911D300801
Part Number:
G0911D301011
Item 7
Item 8
Item 9
Description:
φ4.0*6.0m/m Screw
Description:
M4.0*8m/m Screw
Description:
φ5.0*10m/m Screw
Part Number:
G0911D400601
Part Number:
G0911D400811
Part Number:
G0911D501001