Datalogic Memor X3 User manual

Memor™ X3 Mobile Computer
Quick Start Guide
THE PACKAGE
The Memor X3 package includes the following items:
−1 Memor X3 mobile computer
−1 AC/DC power supply
−1 plug kit
−1 standard Micro USB cable (laser and 2D Imager models only)
−1 hand strap with stylus holder (laser and 2D Imager models
only)
−1 extensible stylus (laser and 2D Imager models only)
−1 guitar pick + cord
−1 Quick Start Guide
−1 Safety and Regulatory Addendum
−1 Wavelink Avalanche Insert
−1 End User License Agreement (EULA) Sheet
−1 Offices Address Addendum
THE TERMINAL
A)
QVGA 64K color display
B)
ON/OFF power key
C)
Speaker
D)
LEDs
E)
Scan key
F)
Keyboard
G)
Microphone
H) Guitar pick stylus
I)
Laser safety label
J)
Rear speaker
K)
Product label (under
battery)
L)
Battery cover
M)
Programmable side key (on
both sides of the mobile
computer)
Before using the device, remove the protective film
from the display and from the data capture window.
NOTE
822001432 (Rev. A) Nov. 2017
N) Data capture window*
O) DC charger connector P) Communication/charger
connector (through cradle)
Q) MicroUSB communication
connector (through cable)
KEYPADS
1.
Cursor Keys
2.
Scan Key
3.
Yellow Modifier
4. Blue Modifier
Special Function Icons
ICON FUNCTION
After a blue modifier key press, it opens the Start
menu.
After a blue modifier key press, it opens the file
manager.
After a blue modifier key press, it switches ON/OFF the
display backlight.
After a blue modifier key press, it switches ON/OFF the
keyboard backlight.
After a blue modifier key press, it
locks and unlocks the
keyboard.
After a blue modifier key press, it disables the
touchscreen and allows the user to control the device
through a joystick-
driven cursor, with Memor X3 side
keys acting as left and right buttons
GETTING STARTED
Insert the Battery
1. Push the latch release button and pull the latch down; then remove
the battery cover.
2. First insert the upper side (contacts), then the bottom side of the
battery pack into the slot:
3. Reinsert the cover. First insert first the upper side and then press
the latch release button and pull the latch down to insert the bottom.
Push the knurled section of the latch upwards to close the cover:
Charge the Battery
With Power Supply
With Single Cradle
Do not use the Memor X3 until batteries are charged
for minimum 4 hours.
CAUTION
SYNCHRONISE YOUR DEVICE WITH THE PC
Set up Synchronisation using Windows Mobile® Device
Center
Windows Mobile® Device Center can be Microsoft
website www.microsoft.com. It is only co ows Vista
and Windows 7; if you run Windows XP or earlier, you have to
download Microsoft ActiveSync.
You can establish a connection to your Memor X3 through the
following interfaces:
−USB either directly or through the Single Dock
−RS232 either directly or through the Single Dock
−Bluetooth®
To establish a partnership between the Memor X3 and a host PC,
start Windows Mobile® Device Center and follow the steps below:
1. Connect the Memor X3 to the host PC. Windows Mobile®
Device Center configures itself and then opens.
2. On the license agreement screen, click Accept.
3. On the Windows Mobile® Device Center’s Home screen, click
Set up your device.
4. Select the information types that you want to synchronize, then
click Next.
5. Enter a device name and click Set Up.
When you finish the setup wizard, Windows Mobile® Device Center
synchronizes the mobile computer automatically. Microsoft® Office
Outlook® emails and other information will appear on your device
after synchronization.
Communicate with Host
N
2
1
4
3
L
I
J
K
M
P
Q
O
F
B
C
A
E
D
G
H
PUSH

Memor™ X3 Mobile Computer
Quick Start Guide
THE PACKAGE
The Memor X3 package includes the following items:
−1 Memor X3 mobile computer
−1 AC/DC power supply
−1 plug kit
−1 standard Micro USB cable (laser and 2D Imager models only)
−1 hand strap with stylus holder (laser and 2D Imager models
only)
−1 extensible stylus (laser and 2D Imager models only)
−1 guitar pick + cord
−1 Quick Start Guide
−1 Safety and Regulatory Addendum
−1 Wavelink Avalanche Insert
−1 End User License Agreement (EULA) Sheet
−1 Offices Address Addendum
THE TERMINAL
A)
QVGA 64K color display
B)
ON/OFF power key
C)
Speaker
D)
LEDs
E)
Scan key
F)
Keyboard
G)
Microphone
H) Guitar pick stylus
I)
Laser safety label
J)
Rear speaker
K)
Product label (under
battery)
L)
Battery cover
M)
Programmable side key (on
both sides of the mobile
computer)
Before using the device, remove the protective film
from the display and from the data capture window.
NOTE
822001432 (Rev. A) Nov. 2017
N) Data capture window*
O) DC charger connector P) Communication/charger
connector (through cradle)
Q) MicroUSB communication
connector (through cable)
KEYPADS
1.
Cursor Keys
2.
Scan Key
3.
Yellow Modifier
4. Blue Modifier
Special Function Icons
ICON FUNCTION
After a blue modifier key press, it opens the Start
menu.
After a blue modifier key press, it opens the file
manager.
After a blue modifier key press, it switches ON/OFF the
display backlight.
After a blue modifier key press, it switches ON/OFF the
keyboard backlight.
After a blue modifier key press, it
locks and unlocks the
keyboard.
After a blue modifier key press, it disables the
touchscreen and allows the user to control the device
through a joystick-
driven cursor, with Memor X3 side
keys acting as left and right buttons
GETTING STARTED
Insert the Battery
1. Push the latch release button and pull the latch down; then remove
the battery cover.
2. First insert the upper side (contacts), then the bottom side of the
battery pack into the slot:
3. Reinsert the cover. First insert first the upper side and then press
the latch release button and pull the latch down to insert the bottom.
Push the knurled section of the latch upwards to close the cover:
Charge the Battery
With Power Supply
With Single Cradle
Do not use the Memor X3 until batteries are charged
for minimum 4 hours.
CAUTION
SYNCHRONISE YOUR DEVICE WITH THE PC
Set up Synchronisation using Windows Mobile® Device
Center
Windows Mobile® Device Center can be Microsoft
website www.microsoft.com. It is only co ows Vista
and Windows 7; if you run Windows XP or earlier, you have to
download Microsoft ActiveSync.
You can establish a connection to your Memor X3 through the
following interfaces:
−USB either directly or through the Single Dock
−RS232 either directly or through the Single Dock
−Bluetooth®
To establish a partnership between the Memor X3 and a host PC,
start Windows Mobile® Device Center and follow the steps below:
1. Connect the Memor X3 to the host PC. Windows Mobile®
Device Center configures itself and then opens.
2. On the license agreement screen, click Accept.
3. On the Windows Mobile® Device Center’s Home screen, click
Set up your device.
4. Select the information types that you want to synchronize, then
click Next.
5. Enter a device name and click Set Up.
When you finish the setup wizard, Windows Mobile® Device Center
synchronizes the mobile computer automatically. Microsoft® Office
Outlook® emails and other information will appear on your device
after synchronization.
Communicate with Host
N
2
1
4
3
L
I
J
K
M
P
Q
O
F
B
C
A
E
D
G
H
PUSH

Memor™ X3 Mobile Computer
Quick Start Guide
THE PACKAGE
The Memor X3 package includes the following items:
−1 Memor X3 mobile computer
−1 AC/DC power supply
−1 plug kit
−1 standard Micro USB cable (laser and 2D Imager models only)
−1 hand strap with stylus holder (laser and 2D Imager models
only)
−1 extensible stylus (laser and 2D Imager models only)
−1 guitar pick + cord
−1 Quick Start Guide
−1 Safety and Regulatory Addendum
−1 Wavelink Avalanche Insert
−1 End User License Agreement (EULA) Sheet
−1 Offices Address Addendum
THE TERMINAL
A)
QVGA 64K color display
B)
ON/OFF power key
C)
Speaker
D)
LEDs
E)
Scan key
F)
Keyboard
G)
Microphone
H) Guitar pick stylus
I)
Laser safety label
J)
Rear speaker
K)
Product label (under
battery)
L)
Battery cover
M)
Programmable side key (on
both sides of the mobile
computer)
Before using the device, remove the protective film
from the display and from the data capture window.
NOTE
822001432 (Rev. A) Nov. 2017
N) Data capture window*
O) DC charger connector P) Communication/charger
connector (through cradle)
Q) MicroUSB communication
connector (through cable)
KEYPADS
1.
Cursor Keys
2.
Scan Key
3.
Yellow Modifier
4. Blue Modifier
Special Function Icons
ICON FUNCTION
After a blue modifier key press, it opens the Start
menu.
After a blue modifier key press, it opens the file
manager.
After a blue modifier key press, it switches ON/OFF the
display backlight.
After a blue modifier key press, it switches ON/OFF the
keyboard backlight.
After a blue modifier key press, it
locks and unlocks the
keyboard.
After a blue modifier key press, it disables the
touchscreen and allows the user to control the device
through a joystick-
driven cursor, with Memor X3 side
keys acting as left and right buttons
GETTING STARTED
Insert the Battery
1. Push the latch release button and pull the latch down; then remove
the battery cover.
2. First insert the upper side (contacts), then the bottom side of the
battery pack into the slot:
3. Reinsert the cover. First insert first the upper side and then press
the latch release button and pull the latch down to insert the bottom.
Push the knurled section of the latch upwards to close the cover:
Charge the Battery
With Power Supply
With Single Cradle
Do not use the Memor X3 until batteries are charged
for minimum 4 hours.
CAUTION
SYNCHRONISE YOUR DEVICE WITH THE PC
Set up Synchronisation using Windows Mobile® Device
Center
Windows Mobile® Device Center can be Microsoft
website www.microsoft.com. It is only co ows Vista
and Windows 7; if you run Windows XP or earlier, you have to
download Microsoft ActiveSync.
You can establish a connection to your Memor X3 through the
following interfaces:
−USB either directly or through the Single Dock
−RS232 either directly or through the Single Dock
−Bluetooth®
To establish a partnership between the Memor X3 and a host PC,
start Windows Mobile® Device Center and follow the steps below:
1. Connect the Memor X3 to the host PC. Windows Mobile®
Device Center configures itself and then opens.
2. On the license agreement screen, click Accept.
3. On the Windows Mobile® Device Center’s Home screen, click
Set up your device.
4. Select the information types that you want to synchronize, then
click Next.
5. Enter a device name and click Set Up.
When you finish the setup wizard, Windows Mobile® Device Center
synchronizes the mobile computer automatically. Microsoft® Office
Outlook® emails and other information will appear on your device
after synchronization.
Communicate with Host
N
2
1
4
3
L
I
J
K
M
P
Q
O
F
B
C
A
E
D
G
H
PUSH

Memor™ X3 Mobile Computer
Quick Start Guide
THE PACKAGE
The Memor X3 package includes the following items:
−1 Memor X3 mobile computer
−1 AC/DC power supply
−1 plug kit
−1 standard Micro USB cable (laser and 2D Imager models only)
−1 hand strap with stylus holder (laser and 2D Imager models
only)
−1 extensible stylus (laser and 2D Imager models only)
−1 guitar pick + cord
−1 Quick Start Guide
−1 Safety and Regulatory Addendum
−1 Wavelink Avalanche Insert
−1 End User License Agreement (EULA) Sheet
−1 Offices Address Addendum
THE TERMINAL
A)
QVGA 64K color display
B)
ON/OFF power key
C)
Speaker
D)
LEDs
E)
Scan key
F)
Keyboard
G)
Microphone
H) Guitar pick stylus
I)
Laser safety label
J)
Rear speaker
K)
Product label (under
battery)
L)
Battery cover
M)
Programmable side key (on
both sides of the mobile
computer)
Before using the device, remove the protective film
from the display and from the data capture window.
NOTE
822001432 (Rev. A) Nov. 2017
N) Data capture window*
O) DC charger connector P) Communication/charger
connector (through cradle)
Q) MicroUSB communication
connector (through cable)
KEYPADS
1.
Cursor Keys
2.
Scan Key
3.
Yellow Modifier
4. Blue Modifier
Special Function Icons
ICON FUNCTION
After a blue modifier key press, it opens the Start
menu.
After a blue modifier key press, it opens the file
manager.
After a blue modifier key press, it switches ON/OFF the
display backlight.
After a blue modifier key press, it switches ON/OFF the
keyboard backlight.
After a blue modifier key press, it
locks and unlocks the
keyboard.
After a blue modifier key press, it disables the
touchscreen and allows the user to control the device
through a joystick-
driven cursor, with Memor X3 side
keys acting as left and right buttons
GETTING STARTED
Insert the Battery
1. Push the latch release button and pull the latch down; then remove
the battery cover.
2. First insert the upper side (contacts), then the bottom side of the
battery pack into the slot:
3. Reinsert the cover. First insert first the upper side and then press
the latch release button and pull the latch down to insert the bottom.
Push the knurled section of the latch upwards to close the cover:
Charge the Battery
With Power Supply
With Single Cradle
Do not use the Memor X3 until batteries are charged
for minimum 4 hours.
CAUTION
SYNCHRONISE YOUR DEVICE WITH THE PC
Set up Synchronisation using Windows Mobile® Device
Center
Windows Mobile® Device Center can be Microsoft
website www.microsoft.com. It is only co ows Vista
and Windows 7; if you run Windows XP or earlier, you have to
download Microsoft ActiveSync.
You can establish a connection to your Memor X3 through the
following interfaces:
−USB either directly or through the Single Dock
−RS232 either directly or through the Single Dock
−Bluetooth®
To establish a partnership between the Memor X3 and a host PC,
start Windows Mobile® Device Center and follow the steps below:
1. Connect the Memor X3 to the host PC. Windows Mobile®
Device Center configures itself and then opens.
2. On the license agreement screen, click Accept.
3. On the Windows Mobile® Device Center’s Home screen, click
Set up your device.
4. Select the information types that you want to synchronize, then
click Next.
5. Enter a device name and click Set Up.
When you finish the setup wizard, Windows Mobile® Device Center
synchronizes the mobile computer automatically. Microsoft® Office
Outlook® emails and other information will appear on your device
after synchronization.
Communicate with Host
N
2
1
4
3
L
I
J
K
M
P
Q
O
F
B
C
A
E
D
G
H
PUSH

INSTALLING A MICROSD CARD
1. Turn off the Memor X3.
2. Push the latch release button and pull the latch down (see
section GETTING STARTED); then remove the cover and
the battery pack:
3. Open the microSD card slot by lifting up the locking plate:
4. Shift the cardholder upwards and then pull it up:
5. Insert the microSD card with the written part upward:
6. Lock the card into place by pushing the cardholder down
and then shifting it downwards; push the locking plate
down:
7. Reinsert the battery cover (see section GETTING
STARTED).
SCANNING AND IMAGING
Laser Data Capture
2D Imager Data Capture
Linear barcode
2D Matrix symbol
ÌBX3ÉÎ
Relative Size and Location of Aiming System Pattern
Linear Imager Data Capture
Scanning with a Memor X3 Linear Imager
When beams reflect directly back into the scanner from the bar code,
they can “blind” the scanner and make decoding difficult.
To avoid this, don’t keep the terminal perpendicular to the barcode:
moving it of a small angle of ±2° is usually enough to enable proper
reading. But don’t scan at too oblique an angle either: keep the scanner
within an angle of ±30° from the perpendicular to the barcode in order to
guarantee effective scanning.
Side Views
REFERENCE DOCUMENTATION
For further information regarding Memor X3 refer to the SDK Help on-
line and to the Memor X3 User’s Manual.
For information regarding safety and regulatory refer to the Safety and
Regulatory Addendum or to the dedicated section of the Memor X3
User’s Manual.
PATENTS
See www.patents.datalogic.com for patent list.
SUPPORT THROUGH THE WEBSITE
Datalogic provides several services as well as technical support
through its website.
Log on to www.datalogic.com and click on the SUPPORT link which
gives you access to:
Downloads by selecting your product model from the dropdown list
in the Search by Product field for specific Data Sheets, Manuals,
Software & Utilities, and Drawings;
Repair Program for On-Line Return Material Authorizations (RMAs)
plus Repair Center contact information;
Customer Service containing details about Maintenance
Agreements;
Technical Support through email or phone.
WARRANTY TERMS AND CONDITIONS
The warranty period is 1 year for the device and 90 days for
consumables (e.g. battery, power supply, cable etc.) from date of
purchase at our company.
©2013-2017 Datalogic S.p.A. and/or its affiliates. All rights reserved.
Datalogic and the Datalogic logo are registered trademarks of
Datalogic S.p.A. in many countries, including the U.S. and the E.U.
Memor is a trademark of Datalogic S.p.A. and/or its affiliates. All
other brand and product names may be trademarks of their
respective owners. www.datalogic.com
Specular reflection.
Reflected beam
is within specular
dead zone and
prevents decode.
No specular
reflection.
Decode can
occur.
Tilt Bar Code At Slight Angle (Up to 30°)
Light
Source
Light
Source

INSTALLING A MICROSD CARD
1. Turn off the Memor X3.
2. Push the latch release button and pull the latch down (see
section GETTING STARTED); then remove the cover and
the battery pack:
3. Open the microSD card slot by lifting up the locking plate:
4. Shift the cardholder upwards and then pull it up:
5. Insert the microSD card with the written part upward:
6. Lock the card into place by pushing the cardholder down
and then shifting it downwards; push the locking plate
down:
7. Reinsert the battery cover (see section GETTING
STARTED).
SCANNING AND IMAGING
Laser Data Capture
2D Imager Data Capture
Linear barcode
2D Matrix symbol
ÌBX3ÉÎ
Relative Size and Location of Aiming System Pattern
Linear Imager Data Capture
Scanning with a Memor X3 Linear Imager
When beams reflect directly back into the scanner from the bar code,
they can “blind” the scanner and make decoding difficult.
To avoid this, don’t keep the terminal perpendicular to the barcode:
moving it of a small angle of ±2° is usually enough to enable proper
reading. But don’t scan at too oblique an angle either: keep the scanner
within an angle of ±30° from the perpendicular to the barcode in order to
guarantee effective scanning.
Side Views
REFERENCE DOCUMENTATION
For further information regarding Memor X3 refer to the SDK Help on-
line and to the Memor X3 User’s Manual.
For information regarding safety and regulatory refer to the Safety and
Regulatory Addendum or to the dedicated section of the Memor X3
User’s Manual.
PATENTS
See www.patents.datalogic.com for patent list.
SUPPORT THROUGH THE WEBSITE
Datalogic provides several services as well as technical support
through its website.
Log on to www.datalogic.com and click on the SUPPORT link which
gives you access to:
Downloads by selecting your product model from the dropdown list
in the Search by Product field for specific Data Sheets, Manuals,
Software & Utilities, and Drawings;
Repair Program for On-Line Return Material Authorizations (RMAs)
plus Repair Center contact information;
Customer Service containing details about Maintenance
Agreements;
Technical Support through email or phone.
WARRANTY TERMS AND CONDITIONS
The warranty period is 1 year for the device and 90 days for
consumables (e.g. battery, power supply, cable etc.) from date of
purchase at our company.
©2013-2017 Datalogic S.p.A. and/or its affiliates. All rights reserved.
Datalogic and the Datalogic logo are registered trademarks of
Datalogic S.p.A. in many countries, including the U.S. and the E.U.
Memor is a trademark of Datalogic S.p.A. and/or its affiliates. All
other brand and product names may be trademarks of their
respective owners. www.datalogic.com
Specular reflection.
Reflected beam
is within specular
dead zone and
prevents decode.
No specular
reflection.
Decode can
occur.
Tilt Bar Code At Slight Angle (Up to 30°)
Light
Source
Light
Source

INSTALLING A MICROSD CARD
1. Turn off the Memor X3.
2. Push the latch release button and pull the latch down (see
section GETTING STARTED); then remove the cover and
the battery pack:
3. Open the microSD card slot by lifting up the locking plate:
4. Shift the cardholder upwards and then pull it up:
5. Insert the microSD card with the written part upward:
6. Lock the card into place by pushing the cardholder down
and then shifting it downwards; push the locking plate
down:
7. Reinsert the battery cover (see section GETTING
STARTED).
SCANNING AND IMAGING
Laser Data Capture
2D Imager Data Capture
Linear barcode
2D Matrix symbol
ÌBX3ÉÎ
Relative Size and Location of Aiming System Pattern
Linear Imager Data Capture
Scanning with a Memor X3 Linear Imager
When beams reflect directly back into the scanner from the bar code,
they can “blind” the scanner and make decoding difficult.
To avoid this, don’t keep the terminal perpendicular to the barcode:
moving it of a small angle of ±2° is usually enough to enable proper
reading. But don’t scan at too oblique an angle either: keep the scanner
within an angle of ±30° from the perpendicular to the barcode in order to
guarantee effective scanning.
Side Views
REFERENCE DOCUMENTATION
For further information regarding Memor X3 refer to the SDK Help on-
line and to the Memor X3 User’s Manual.
For information regarding safety and regulatory refer to the Safety and
Regulatory Addendum or to the dedicated section of the Memor X3
User’s Manual.
PATENTS
See www.patents.datalogic.com for patent list.
SUPPORT THROUGH THE WEBSITE
Datalogic provides several services as well as technical support
through its website.
Log on to www.datalogic.com and click on the SUPPORT link which
gives you access to:
Downloads by selecting your product model from the dropdown list
in the Search by Product field for specific Data Sheets, Manuals,
Software & Utilities, and Drawings;
Repair Program for On-Line Return Material Authorizations (RMAs)
plus Repair Center contact information;
Customer Service containing details about Maintenance
Agreements;
Technical Support through email or phone.
WARRANTY TERMS AND CONDITIONS
The warranty period is 1 year for the device and 90 days for
consumables (e.g. battery, power supply, cable etc.) from date of
purchase at our company.
©2013-2017 Datalogic S.p.A. and/or its affiliates. All rights reserved.
Datalogic and the Datalogic logo are registered trademarks of
Datalogic S.p.A. in many countries, including the U.S. and the E.U.
Memor is a trademark of Datalogic S.p.A. and/or its affiliates. All
other brand and product names may be trademarks of their
respective owners. www.datalogic.com
Specular reflection.
Reflected beam
is within specular
dead zone and
prevents decode.
No specular
reflection.
Decode can
occur.
Tilt Bar Code At Slight Angle (Up to 30°)
Light
Source
Light
Source

INSTALLING A MICROSD CARD
1. Turn off the Memor X3.
2. Push the latch release button and pull the latch down (see
section GETTING STARTED); then remove the cover and
the battery pack:
3. Open the microSD card slot by lifting up the locking plate:
4. Shift the cardholder upwards and then pull it up:
5. Insert the microSD card with the written part upward:
6. Lock the card into place by pushing the cardholder down
and then shifting it downwards; push the locking plate
down:
7. Reinsert the battery cover (see section GETTING
STARTED).
SCANNING AND IMAGING
Laser Data Capture
2D Imager Data Capture
Linear barcode
2D Matrix symbol
ÌBX3ÉÎ
Relative Size and Location of Aiming System Pattern
Linear Imager Data Capture
Scanning with a Memor X3 Linear Imager
When beams reflect directly back into the scanner from the bar code,
they can “blind” the scanner and make decoding difficult.
To avoid this, don’t keep the terminal perpendicular to the barcode:
moving it of a small angle of ±2° is usually enough to enable proper
reading. But don’t scan at too oblique an angle either: keep the scanner
within an angle of ±30° from the perpendicular to the barcode in order to
guarantee effective scanning.
Side Views
REFERENCE DOCUMENTATION
For further information regarding Memor X3 refer to the SDK Help on-
line and to the Memor X3 User’s Manual.
For information regarding safety and regulatory refer to the Safety and
Regulatory Addendum or to the dedicated section of the Memor X3
User’s Manual.
PATENTS
See www.patents.datalogic.com for patent list.
SUPPORT THROUGH THE WEBSITE
Datalogic provides several services as well as technical support
through its website.
Log on to www.datalogic.com and click on the SUPPORT link which
gives you access to:
Downloads by selecting your product model from the dropdown list
in the Search by Product field for specific Data Sheets, Manuals,
Software & Utilities, and Drawings;
Repair Program for On-Line Return Material Authorizations (RMAs)
plus Repair Center contact information;
Customer Service containing details about Maintenance
Agreements;
Technical Support through email or phone.
WARRANTY TERMS AND CONDITIONS
The warranty period is 1 year for the device and 90 days for
consumables (e.g. battery, power supply, cable etc.) from date of
purchase at our company.
©2013-2017 Datalogic S.p.A. and/or its affiliates. All rights reserved.
Datalogic and the Datalogic logo are registered trademarks of
Datalogic S.p.A. in many countries, including the U.S. and the E.U.
Memor is a trademark of Datalogic S.p.A. and/or its affiliates. All
other brand and product names may be trademarks of their
respective owners. www.datalogic.com
Specular reflection.
Reflected beam
is within specular
dead zone and
prevents decode.
No specular
reflection.
Decode can
occur.
Tilt Bar Code At Slight Angle (Up to 30°)
Light
Source
Light
Source