Datalogic DS1500-1100 User manual

DS1500 QUICK GUIDE
DS1500
General View:
1
2
3
4 8
7
6
5 Mounting Holes
Good Read LED
External Trigger/Ready LED
Tx Data/Active LED
Laser On LED
Laser Beam Output Window
Test Key
Power On LED
Warning and Device Class Label
9
Product Label
10
15-pin D-sub Male Connector
11
Figure A
For further details on product installation, see the complete Reference Manual.
DS1500 can be configured through the WinHost Windows-based software program available on the
installation CD-ROM (part number 93ACC1771).
For configuration it is necessary to create a cable connecting the scanner to the PC as indicated in the
“How To Build A Simple Interface Test Cable” section of this guide.
2
1
3
4
56 7
9
8
10 11

DS1500 QUICK GUIDE
2
Power Supply:
- This product is intended to be installed by Qualified Personnel only.
- All Models:
This accessory device is intended to be supplied by a UL Listed or CSA Certified Power Unit with «Class 2» or
LPS power source, which supplies power directly to the scanner via the 15-pin connector.
The scanner is classified as a Class 2 laser product according to EN 60825-1 regulations and as a Class II laser
product according to CDRH regulations.
Disconnect the power supply when opening the device during maintenance or installation to avoid exposure to
hazardous laser light.
There is a safety device, which allows the laser to be switched on only if the motor is rotating above the threshold
for its correct scanning speed.
The laser beam can be switched off through a software command (see also the WinHost Help On Line).
Warning and Device Class Label
The laser diode used in this device is classified as a class 3B laser product according to EN 60825-1 regulations
and as a Class IIIb laser product according to CDRH regulations. As it is not possible to apply a classification
label on the laser diode used in this device, the following label is reproduced below.
LASER LIGHT
AVOID EXPOSURE TO BEAM
CLASS 3B LASER PRODUCT
MAX. OUTPUT RADIATION 35 mW
EMITTED WAVE LENGTH 630~680 nm
TO EN 60825-1 (2001)
Laser Diode Class Label
Any violation of the optic parts in particular can cause radiation up to the maximum level of the laser diode (35
mW at 630 to 680 nm).

DS1500 QUICK GUIDE
3
Model Description:
DS1500 - X X 0 0
Optical Resolution
1 = Standard Resolution
2 = High resolution
Communication Interface
1 = RS232/RS485main + RS232 aux
Reading Performance:
Version Reading Distance Max Code
Resolution Speed
mm (mils) scans/s
1100 40 mm (1.6 in) - 240 mm (9.4 in) on 0.50mm (20 mils) codes 0.20 (8) 1200
1100 75 mm (2.9 in) - 115 mm (4.5 in) on 0.15mm (6 mils) codes 0.15 (6) 800
2100 50 mm (2 in) - 125 mm (4.9 in) on 0.20mm (8 mils) codes 0.10 (4) 800
Technical Features:
ELECTRICAL FEATURES
Input Power
Supply voltage 5 Vdc±5%
Power consumption max. 2 W
Serial Interfaces
Main RS232; RS485 Full-duplex / Half-duplex
Auxiliary RS232
Baud Rates 150 to 115200
Inputs External Trigger
Voltage max. 40 Vdc
Outputs OUT1, OUT2
VCE max. 40 Vdc
Collector current max. 20 mA continuous;
VCE saturation 0.3V at 6 mA max.
Power dissipation max. 100 mW at 45 °C (Ambient temp.)
OPTICAL FEATURES
Light source Semiconductor laser diode
Wave length (Note 1) 630 to 680 nm
Safety class Class 2 - EN 60825-1; Class II - CDRH
READING FEATURES
Scan rate (software programmable) 800 to 1200 scans/sec
Aperture angle
Maximum Reading distance See reading diagrams
Maximum resolution
USER INTERFACE
LED indicators Laser ON, Tx Data/ACT, Ext Trig/RDY,
Good Read, Power ON

DS1500 QUICK GUIDE
4
SOFTWARE FEATURES
READABLE CODE SYMBOLOGIES
* EAN/UPC * Code 93
EAN/UPC (including Add-on 2 and Add-on 5) * Code 128
* 2/5 Interleaved * EAN 128
* Code 39 (Standard and Full ASCII) ISBT 128
* Codabar Pharmacode
*ACB Readable. Other symbologies available on request.
Code Selection up to six different codes during one reading phase
Decoding Safety can enable multiple good reads of same code
Headers and Terminators up to four headers and four terminators
Operating Modes On-Line, Serial-On-Line, Automatic, Continuous, Test
Configuration Modes • through menus using WinHost utility
• receiving commands from one of the serial ports (HOST
MODE)
Special Functions ACB (Advanced Code Builder)
Motor Off
Parameter Storage Non-volatile internal EEPROM
ENVIRONMENTAL FEATURES
Operating temperature (Note 2) 0° to 45 °C (32° to 113 °F)
Storage temperature -20° to 70 °C (-4° to 158 °F)
Humidity max. 90% non condensing
Vibration resistance 14 mm @ 2 to 10 Hz
EN 60068-2-6
2 hours on each axis
1.5 mm @ 13 to 55 Hz
2 g @ 70 to 200 Hz
Shock resistance
EN 60068-2-27
3 shocks on each axis 30 g; 11 ms
Protection class IP65
PHYSICAL FEATURES
Mechanical dimensions 40 x 30 x 22 mm (1.57 x 1.18 x 0.86 in)
Weight without cable 44 g (1.55 oz)
Note 1: The features given are typical at a 25 °C ambient temperature (if not otherwise indicated).
Note 2: If the reader is used in high temperature environments (over 40 °C), it is advised the use of the Beam-
shutter (see the WinHost configuration program) and/or a thermal conductive support (such as the
metal bracket provided).

DS1500 QUICK GUIDE
5
Accessories:
Name Description Part Number
CONFIG / DOC PKG DS1500 Configuration SW, Reference Manual, Test Chart, other
documentation
93ACC1771
Electrical Connections:
DS1500 is equipped with a cable terminated by a 15-pin male High Density D-sub connector for connection to the
power supply and input/output signals.
CAUTION
Do not connect GND and SGND to different (external) ground references. GND and SGND are
internally connected through filtering circuitry which can be permanently damaged if subjected
to voltage drops over 0.8 Vdc.
The details of the connector pins are indicated in the following table:
15-pin male high density D-sub connector pinout
Pin Name Function
1 VS Power supply input voltage +
5 GND Power supply input voltage -
8 PE Protective Earth Ground
13 SHIELD Cable Shield
9 EXT TRIG - External Trigger -
7 OUT1 + Output 1 +
14 OUT2 + Output 2 +
11, 12, 15 NC Not Connected
15-pin D-sub High-Density Male Connector
Pin RS232 RS485
Full-Duplex
RS485
Half-Duplex
2 TX232 Main TX485- RTX485-
3 RX232 Main RX485+
6 TXAUX TX485+ RTX485+
10 RXAUX RX485-
4 SGND SGND SGND

DS1500 QUICK GUIDE
6
Mechanical Installation:
3.9
[0.15]
30
[1.18]
13.7
[0.54]
34.1
[1.34]
=
5.3
[0.21]
7.6
[0.30]
=
31.3
[1.23]
3.1
[0.12]
N°2
4.6
[0.18]
22
[0.87]
40
[1.57]
1
[0.04]
mm
inch
*
MØ2
3.2
[0.13]
3.2
[0.13]
=
11
[0.43]
6
[0.24]
=
62
[2.44]
20
[0.79]
25
[0.98]
1.5
[0.06]
inch
mm
7.1
[0.28]
31.8
[1.25]
31.8
[1.25]
25.1
[0.99]
12
[0.47]
==
* The quote refers to the scan line
DS1500 Overall Dimensions Mounting Bracket Overall Dimensions
Skew
Pitch

DS1500 QUICK GUIDE
7
Input/Output Connections:
INPUT CONNECTIONS
1
9
VS
EXT TRIG -
5 GND
EXTERNAL TRIGGER
Ground
V
DS1500
Signal
+ 5 V
47 K
External Trigger Input Command using Scanner Power
1
9
VS
EXT TRIG -
5 GND
EXTERNAL TRIGGER
Ground
V
DS1500
Signal
+ 5 V
47 K
40 Vdc max
External Trigger Input Command using External Power
OUTPUT CONNECTIONS
USER INTERFACE
Vext 40 Vdc max.,
20 mA max.
DS1500
7/14
5
+
GND Ground
VCE max = 40 Vdc
I max = 20 mA continuous
Connectivity:
RS232 Point-to-point Layout RS485 Point-to-point Layout
Terminal Host
DS1500
3
1
2
Host
DS1500
2
1
cMain Serial Interface (RS232) cMain Serial Interface (RS485 Full Duplex)
dAuxiliary Serial Interface (Local Echo) dExternal Trigger (for On-Line Mode)
eExternal Trigger (for On-Line Mode)
RS232 Pass-through Layout
Host
1
DS1500 2
3 3
1
DS1500
cMain Serial Interface
dAuxiliary Serial Interface
eExternal Trigger (for On-Line Mode)

DS1500 QUICK GUIDE
8
Connectivity:
RS232 Master/slave Layout Multiplexer Layout
Host
1
2
3
2
DS1500
Slave
1
1
DS1500
Slave DS1500
Master
Host
2
1
MX4000
22
01 31
cMain Serial Interface cMain Serial Interface
dAuxiliary Serial Interface dExternal Trigger (for On-Line Mode)
eExternal Trigger (for On-Line Mode)
Reading Diagrams:
DS1500-1100
2
1
0
1
5
4
3
2
3
4
5
(in)
0 1 32 106(in) 45 7 89
0 20 40 60
80 100 120 140 160 180 200 220 240 260 (mm)
120
100
80
60
40
20
0
20
40
60
80
100
120
(mm)
0.50 mm
(20 mils)
0.20 mm
(8 mils)
0.15 mm
(6 mils)
0.30 mm
(12 mils)
NOTE: (0,0) is the center of the laser beam output window.
CONDITIONS
Code = Interleaved 2/5 or Code 39
PCS = 0.90
"Pitch" angle = 0°
"Skew" angle = 15°
"Tilt" angle = 0°
*Motor Control = Speed_3 (800 scans/s) for 0.15mm codes, Speed_4 (1200 scans/s) for 0.20mm codes and greater
* Parameter selectable in Winhost

DS1500 QUICK GUIDE
9
DS1500-2100
1
0.5
0
0.5
2.5
2
1.5
1
1.5
2
2.5
(in)
01 53 (in) 24
0 10 20 30
40 50 60 70 80 90 100 110 120 130 (mm)
60
50
40
30
20
10
0
10
20
30
40
50
60
(mm)
0.20 mm
(8 mils)
0.12 mm
(5 mils)
0.10 mm
(4 mils)
0.5 3.5 4.5
1.5 2.5
0.15 mm
(6 mils)
NOTE: (0,0) is the center of the laser beam output window.
CONDITIONS
Code = Interleaved 2/5 or Code 39
PCS = 0.90
"Pitch" angle = 0°
"Skew" angle = 15°
"Tilt" angle = 0°
*Motor Control = Speed_3 (800 scans/s)
• Parameter selectable in Winhost

DS1500 QUICK GUIDE
10
User Interface:
The following table contains the pinout for standard RS232 PC Host interface. For other user interface types
please refer to their own manual.
RS232 PC-side connections
1 5
96
9-pin male connector
13
2514
1
25-pin male connector
Pin Name Pin Name
2 RX 3 RX
3 TX 2 TX
5 GND 7 GND
7 RTS 4 RTS
8 CTS 5 CTS
How To Build A Simple Interface Test Cable:
The following wiring diagrams show a simple test cable including power, external (push-button) trigger and PC
RS232 COM port connections.
PC
15-pin D-sub HD female
4
10
SGND
RXAUX
TXAUX
6
DS1500 5
1
GND
VS
9-pin D-sub female
GND
TX
RX
2
3
5
Power Supply
VS (5 Vdc)
Power GND
Trigger
EXT TRIG-
9
Test Cable for DS1500
NOTE
The Auxiliary RS232 interface is only available when the main interface is RS232.