Datalogic DX8200A-3002 User manual

DX8200A-3002 QUICK GUIDE
DX8200A-3002
General View:
Figure A
Laser Beam Output Windows
1
Mounting Slots
2
Laser Safety Label
3
Mounting Reference Label
4
Figure B
Programming Keypad
1
Phase On LED (Yellow)
3
Power On LED (Green)
2
TX Data LED (Green)
5
Network LED (Red)
6
Encoder LED (Yellow)
4
LCD Display
7
Figure C
Lonworks 17-pin Male Connector
1
Lonworks 17-pin Female Connector
2
NOTE
For further details on product installation, see the complete Reference Manual available on the
configuration CD-ROM included with this product.
1
2
7
34 5 6
1 2
2
1
2
3
4

DX8200A-3002 QUICK GUIDE
2
Technical Features:
ELECTRICAL FEATURES
Supply voltage 20 to 30 Vdc
Power consumption 30 W typical
35 W Max. (including startup current)
Communication Interfaces Auxiliary Baud Rate
RS232 1200 to 115200
Other
Lonworks 1.25 Mb/s
OPTICAL FEATURES
Light receiver Avalanche photodiode
Wavelength 630 to 680 nm
Safety class Class 2 - EN60825-1; Class II - CDRH
Light source Up to 4 semiconductor laser diodes
Laser control Security system to turn laser off in case of motor slow down
READING FEATURES
Scan rate ≤1000 scans/s (500 per leg)
Maximum resolution
Max. reading distance
Max. reading width
Max. depth of field
(see reading diagrams on page 9)
USER INTERFACE
LCD Display 2 lines by 20 characters LCD
Keypad 3 keys
LED indicators Power On (green)
Phase On (yellow)
Encoder (yellow)
TX Data (green)
Network (red)
SOFTWARE FEATURES
Readable Codes Interleaved 2/5
Code 39 Standard
Codabar
Code 128
EAN 128
Code 93 (standard and full ASCII)
EAN/UPC (including Add-on 2 and Add-on 5)
Code selection Up to 10 codes during one reading phase
Operating modes PackTrack™
Configuration modes Genius™ utility program
Parameter storage Non-volatile internal FLASH

DX8200A-3002 QUICK GUIDE
3
ENVIRONMENTAL FEATURES
Operating temperature 0° to +50 °C (+32° to +122 °F)
Storage temperature -20° to +70 °C (-4° to +158 °F)
Humidity 90% non condensing
Ambient light immunity 20000 lux
Vibration resistance:
EN 60068-2-6
2 hours on each axis
Frequency range from 5 to 150 Hz;
Constant displacement 3 mm pk-pk from 5 to 9 Hz;
Constant acceleration 0.5 g from 9 to 150 Hz;
Shock resistance:
IEC 68-2-27 test EA
3 shocks on each axis 30 g; 11 ms
Protection Class IP65*
PHYSICAL FEATURES
Mechanical dimensions 470 x 300 x 141 mm (18.50 x 11.81 x 5.55 in)
Weight about 11 kg (24 lbs 3 oz)
* IP65 cables and connectors required (CAB-850x or BTK-8500).
Accessories:
NAME Description Part Number
PWO-480 Power and Connect System 480W 93ACC1767
FS-1 Frame Shaper (8 pcs) 93ACC1750
S30 Photocell Kit 93ACC1782
MEP-542 Photocell Kit - PNP 93ACC1727
MEP-543 Photocell Kit - NPN 93ACC1728
OEK-2 Optical Encoder Kit + 10 m cable + Spring 93ACC1770
OEK-1 Optical Encoder Kit + 10 m cable 93ACC1600
BTK-8100 Bus Terminator Kit (5 pcs) 93ACC1090
BTK-8500 IP65 Terminator Kit (2 pcs) 93A051286
PLL-8000 Optocoupled PLL device 93ACC1280
CAB-8100 10 wire shielded cable D 9.5 mm – 50 m 93ACC1120
CAB-8101 17-pin scanner/scanner connection cable 1.2 m 93A051020
CAB-8102 17-pin scanner/scanner connection cable 2.5 m 93A051030
CAB-8105 17-pin scanner/scanner connection cable 5 m 93A051040
CAB-8501 IP65 Cable Fam 8K 1,2 m 93A051283
CAB-8502 IP65 Cable Fam 8K 2,5 m 93A051284
CAB-8505 IP65 Cable Fam 8K 5 m 93A051285
Sentinel-5 Supervisor (up to 5 arrays) 93A101004
Sentinel-10 Supervisor (up to 10 arrays) 93A101005
Sentinel-32 Supervisor (up to 32 arrays) 93A101007

DX8200A-3002 QUICK GUIDE
4
Electrical Connections:
Two 17-pin connectors provide access to the scanner’s local Lonworks network used for both input and output
connections to build a multi-sided or omni-station system.
17-pin Lonworks Connector Pinout
Pin Name Function
A1 GND Supply voltage (negative pin)
A2 VS Supply voltage 20 to 30 Vdc (positive pin)
Cable shield A - internally connected by
1 CHASSIS capacitor to chassis
2 n.c. Not connected
Cable shield B - internally connected by
3 CHASSIS capacitor to chassis
4 TXAUX Transmit data of auxiliary RS232
(referred to SGND)
5 SGND Signal ground (connected to GND)
6 RXAUX Receive data of auxiliary RS232
(referred to SGND)
7 VS_I/O Supply voltage of I/O circuit
8 Lon A+ Lonworks a line (positive pin)
9 Lon A- Lonworks a line (negative pin)
10 Lon B+ Lonworks b line (positive pin)
11 Lon B- Lonworks b line (negative pin)
12 SYS_I/O System signal
13 SYS_ENC_I/O System signal
14 Reserved Internally connected
15 Ref_I/O Reference voltage of I/O circuit
A1 A2
1
15
Female - Output
A1 A2
1
15
Male - Input
17-pin Local Lonworks Connectors

DX8200A-3002 QUICK GUIDE
5
Connectivity:
DX8200A-3002 Typical Layout
Extended I/O
Host
HUB
ETHERNET
SC6000 AUX
CAB-SC6003
CAB-SC6003
Power/Net
VAC INPUT
CAB-SC6103
Cable
PWO
LONWORKS
ENCODER
PS
PS Aux
CAB-850x
CAB-850x
CAB-850x CAB-850x
up to 3
scanners
per
branch
BTK8500
Bus Return
DX8200A-3002
DS8100A-3002
CAB-850x
up to 4
scanners per
branch
BTK8500
Bus Return
DX8200A-3002 DX8200A-3002
DS8100A-3002
DS8100A-3002
DS8100A-3002
CAB-850x CAB-850x

DX8200A-3002 QUICK GUIDE
6
Example of Redundant System Layout
AUX
CAB-SC6103
Extended I/O
ETHERNET
SC6000
CAB-SC6003
CAB-SC6003
Power/Net
VAC INPUT
PWO
LONWORKS
ENCODER
PS
PS Aux
CAB-850x
CAB-850x
BTK8500
CAB-850X
CAB-850x CAB-850x
Extended I/O
ETHERNET
SC6000
CAB-SC6003
CAB-SC6003
Power/Net
VAC INPUT
PWO
CAB-PWO 03
Redundancy
CAB-850X
CAB-850x CAB-850x BTK8500
DX8200A DX8200A DS8100A DS8100A
ENCODER
PS
PS Aux
LONWORKS
Working
Controller
Protecting
Controlle
r
to Host
to Host
DX8200A DX8200A DS8100A DS8100A

DX8200A-3002 QUICK GUIDE
7
Example of Redundant System

DX8200A-3002 QUICK GUIDE
8
Mechanical Installation:
DX8200A-3002 can be installed to operate in any position. There are 4 slots (dia. 8.5 mm) on the sides of the
scanner for mounting. The diagram below can be used for installation; refer to the Reading Diagrams for correct
positioning of the scanner with respect to the reading zone and scanner orientation.
470
[18.50]
300
[11.81]
== 180
[7.09]
22
[0.87]
406
[15.98]
22
[0.87]
8.5
[0.33]
141
[5.55]
147
[5.79]
10
[0.39]
370
[14.57] ==
370
[14.57]
= =
==
60.5
[2.38]
70.5
[2.78]
N° 4
DX8200A-3002 Overall Dimensions
Scanner Direction
The different scanner orientations are illustrated in the following figures:
DX8200A-3002 Scanner Direction 0° (Forward) DX8200A-3002 Scanner Direction 180° (Reverse)
PackTrack™ Coordinate Reference Point
where x, y, z = 0
Top View
Conveyor Direction
Top View
Conveyor Direction

DX8200A-3002 QUICK GUIDE
9
Reading Diagrams:
Note: x = 0 and z = 0 correspond to the edge of the DX8200A-3002 scanner as shown in the figure below.
DX8200A-3002 (0.50 mm/20 mils)
CONDITIONS
Code = Interleaved 2/5 or Code 39
PCS = 0.90
0-24 -40 (in)
-32 -48
0-60 -80 (cm)
-100 -120 -140 -160
-56 -64
(in)
-30
-20
0
-10
(cm)
-50
-60
-70
-40
30
20
10
50
60
70
40
-12
-8
0
-4
-20
-24
-28
-16
12
8
4
20
24
28
16
-40
-15
Compliance:
Laser Safety
Figure A
Warning and Device Class Label
1
Figure B
Device Identification Label
1
The scanner is classified as a Class 2 laser product according to EN60825-1 regulations and as a Class II laser
product according to CDRH regulations.
Disconnect the power supply when opening the device during maintenance or installation to avoid exposure to
hazardous laser light.
There is a safety device, which allows the laser to be switched on only if the motor is rotating above the threshold
for its correct scanning speed.
1
1
z
x

DX8200A-3002 QUICK GUIDE
10
The laser beam can be switched off through a software command (see also the Genius™ Help On-Line).
LASER LIGHT
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
MAXIMUM OUTPUT RADIATION 1 mW
EMITTED WAVELENGTH 630~680 nm
TO EN 60825-1:2001
CAUTION-CLASS 3B LASER LIGHT WHEN OPEN
AVOID EXPOSURE TO BEAM
LASER LIGHT EMITTED
FROM THIS
APERTURE
Warning and Device Class Label
Model No. Amp.
Serial No.
DATALOGIC S.P.A. Via Candini, 2
40012 Calderara di Reno - Bologna - Italy
Manufactured Volt
This product conforms to the applicable requirements
of 21CFR1040 at the date of manufacture.
Device Identification Label
The laser diodes used in this device are classified as Class 3B laser products according to EN 60825-1 regulations
and as Class IIIb laser products according to CDRH regulations. As it is not possible to apply a classification label
on the laser diodes used in this device, the following label is reproduced here:
LASER LIGHT
AVOID EXPOSURE TO BEAM
CLASS 3B LASER PRODUCT
MAXIMUM OUTPUT RADIATION 30 mW
EMITTED WAVELENGTH 630~680 nm
TO EN 60825-1 (2001)
Laser Diode Class Label
Any violation of the optic parts in particular can cause radiation up to the maximum level of the laser diode
(30 mW at 630~680 nm).
Power Supply
This product is intended to be installed by Qualified Personnel only.
- This scanner is intended to be supplied by either a UL Listed power supply marked 'Class 2' or 'LPS', output
rated 20 - 30 V dc, minimum 1.75 A or by a UL Listed computer with LPS outputs.
- This scanner must be supplied by a Class II Power Supply Unit conforming to the EN 60950 safety
regulation.
WEEE Compliance