dB Technologies ingenia ig3t Manual

www.dbtechnologies.com [e-mail]
INGENIA IG3T Rev 1.1 cod. 4 01 0 39Q
IG3T
Quick start user manual
Section 1
The warnings in this manual must be observed together with the "User Manual - Section 2".
Le avvertenze nel presente manuale devono essere osservate congiuntamente al MANUALE D’USO - Sezione2”.
Die Warnungen in diesem Handbuch müssen in Verbindung mit der "BEDIENUNGSANLEITUNG - Abschnitt 2" beobachtet
werden”.
Les avertissements specifiés dans ce manuel doivent être respectés ainsi que les "CARACTERISTIQUES TECHNIQUES -
Section 2"
A.E.B. Industriale Srl Via Brodolini, 8 Località Crespellano 40053 VALSAM GGIA B L GNA (ITALIA)
Tel [phone] Fax [phone] www.dbtechnologies.com [e-mail]

www.dbtechnologies.com [e-mail]
INGENIA IG3T Rev 1.1 cod. 4 01 0 39Q
Thank you for choosing a dBTechnologies Product!
INGENIA IG3T is a powerful 2-way vertical speaker, equipped with one 1.4” compression driver with a 3” voice coil
and two 10” woofers, in an innovative shape. The horn of the driver is vertically asymmetrical, for a precise acoustical
coverage in different kind of installations, indoor and outdoor. The powerful DIGIPR ® G3 amplifier section, capable
of handling up to 900 W (RMS power), is controlled by a DSP, which can perform a detailed customization of the
output sound of the speaker. In particular, the DSP can recognize if 2 INGENIA IG3Ts are installed together, stacked
or flown, through the special IR communication handles, and can perform a digital steering, making them sound as
one single source with a selectable inclination. All the DSP parameters can be viewed and selected in the user-
friendly interface, equipped with a self-rotating LED display, and can be saved and reloaded in different custom
settings by the user, who can protect his choices with a password.
Check the site www.dbtechnologies.com for the complete user manual!
1) Unpacking
The box contains:
N°1 INGENIA IG3T
N°1 Mains cable with Neutrik® powerC N TRUE
connector
N°1 100-120 V FUSE
This quick start and warranty documentation.
2) Easy Assembly
The speaker can be configured in 5 main modes:
Option 1: Single Mode (1 speaker mounted on an
optional pole stand)
The speaker is equipped with a standard pole-
mounting hole, so it can be mounted on a D35 mm
optional pole stand (tripod). For a safe installation, it
is not admitted a 2-speakers mounting, and the user
must check the stability of the system. The maximum
admitted height is 120 cm (47.25 inch.).
Option 2: Stacked on a subwoofer (1 or 2 speakers)
The speaker can be mounted on a subwoofer with D35
pole mounting hole, using a GSA-IG optional adapter.
It is mandatory to use an additional fastening system.
Option 3: On the floor (1 or 2 speakers)
The speaker can be mounted on the floor, only using a
GSA-IG optional adapter. In this case it is mandatory to
use an additional fastening system or straps.
Option 4: Pole-mounted on a subwoofer (1 speaker)
Only one speaker can be installed on a D 5 pole
(maximum height: 120 cm – 47.25 in.), mounted on a
subwoofer. It is mandatory to use an additional
fastening system to secure properly the installation.
Option 5: Flown (1 or 2 speakers)
The speaker can be mounted flown, using the optional
DRK-IG fly bar and TGA-IG truss adapter.
In a 2 speakers configuration, it is mandatory to use a
couple of LP IG optional link brackets to mount them
together. / Other kinds of installation not illustrated in
this manual are not admitted. /Don’t cover the handles in
any way, they are equipped with infrared ports!
3) Connections and OLED Display
The INGENIA speakers are equipped with an intuitive
LED display. All the connections are in the amplifier
panel side:
1 – Peak led.
2 – LED Display.
3 – Push rotary encoder (rotate: select, push: confirm).
4 – Mini B-type USB port (for firmware updating).
5 – Link audio output.
6 – Combo line/mic input.
7 – Input sense switch (LINE/MIC).
Single Mode
(only 1 IG3T)
Stacked on
a subwoofer
(1 or 2 IG3
T)
Flown
(1 or 2 IG3T)
On t e floor
(1 or 2 IG3T)
Pole-
mounted on
a subwoofer
(only 1 IG3T)

www.dbtechnologies.com [e-mail]
INGENIA IG3T Rev 1.1 cod. 4 01 0 39Q
8 – Auto-range mains (power) input.
9 – Mains (power) link output.
10 – Mains fuse.
The fuse is factory setted for 220-240 V operation.
If it is necessary to change the fuse to 100-120V range:
1. Disconnect the speaker fro any cable
2. Wait 5 inutes
3. Substitute the fuse with the correct one supplied
Use only cables with Neutrik® connectors!
4) Ready in less than a minute – Build System menu
The internal DSP provides an easy setup of installation
and allows to configure quickly the IG3T. Even if you
turn off the speaker, your setting will be saved for the
next session!
Set up instructions
nce you have properly
connected the power supply
and audio input (remember to
select the proper “LINE”/”MIC”
choice in input sense switch (7)),
select the gain level in the first
display window, rotating the
push rotary encoder, then push
it to access the menu choice
wizard.
1. Select and confirm
“Build System”,
2. Select and confirm the
"Selfcheck System” to
launch the automatic
recognition procedure
and select and confirm
“NEXT”
3. In the next “System
Structure” menu you
can find the number of
“Speakers” automatically recognized, and you
can choose and confirm the number of
“Subwoofers” you want to use in your
configuration. Then select and confirm “NEXT”
4. In “System Type” you can specify the “Stacked”
(on the floor - pole mounting – subwoofer
mounting) or “Flown” (fly-bar mounting) type
of installation. Then select and confirm “NEXT”
Holding the rotary encoder, you return to the main
Gain/Level window, from each submenu window.
If the system has automatically recognized the
presence of 2 speakers, the next menu will be “System
coverage”. If you have selected the presence of a
subwoofer in your installation, the next menu will be
the “Subwoofer Matching” menu.
5) System Coverage
The INGENIA IG3T’s powerful
DSP can act as a custom delay
line on the transducers, in
order to direct the final acoustical coverage of the
speaker. This menu will appear only when the DSP has
recognized 2 IG3Ts thanks to the infrared handles.
You can choose up to 7 factory settings:
a. UP +10°, for the maximum inclination angle
(with speakers mounted on the floor, on a
stand or a subwoofer)
b. UP +5°, for a medium inclination angle (with
speakers mounted on the floor, on a stand or
a subwoofer)
c. UP +2.5°, for a low inclination angle (with
speakers mounted on the floor, on a stand or
a subwoofer)
d. FAR 0°, for the maximum distance coverage in
a position directly at the level of the audience
e. D WN -2.5°, for a long-distance coverage
(flown speakers)
f. D WN -5°, for a medium-distance coverage
(flown speakers)
g. D WN -10°, for a short-distance coverage
(flown speakers)
6) Subwoofer Matching
nce you have chosen to
match the system to one or
more subwoofers, a menu
will appear allowing you to
select: the model and the HP
Filter frequency, and the system will suggest you the
correct subwoofer delay.
7) System Delay
You can set a custom delay
on your speakers in
milliseconds, meters or feet,
in order to align your
speakers with the main sound system (see the picture
below).
8) Stage Alignment
When you are on stage and
you have different acoustic
sources (for example the
drums of a band) you can choose to align your
speaker with those sources. In this menu you can set
the distance in meters or feet, or the time in ms.
SUPERUSER PASSWORD
You can set a Password in OPTIONS 
PASSWORD
in order to protect your custo settings.
If you forget the password, use the code: Q2R5D9
to unlock the syste .

www.dbtechnologies.com [e-mail]
INGENIA IG3T Rev 1.1 cod. 4 01 0 39Q
Technical Data
Speaker Type: 2-way Active Speaker
Acoustical data
Frequency Response [-10dB]: 53 - 20.000 Hz
Frequency Response [-6dB]: 57 – 19.200 Hz
Max SPL: 132 dB
HF compression driver: 1.4" Exit
HF voice coil: 3” Titanium
Horn Coverage (HxV): 110 x 90° (+20°/-70°)
Directivity: Vertical asymmetric
HF type: Neodymium compression driver
Crossover frequency: 1100 Hz
LF: 2x10”
LF Voice Coil: 2.5”
LF Type: Neodymium
Amplifier
Amp Technology: Digipro® G3
Amp Class: Class-D
RMS Power: 900 W
Peak Power: 1800 W
Processor
Controller: DSP 56 bit
AD/DA Converter: 24 bit / 48 kHz
Limiter: Dual Active, Peak, RMS, Thermal
Input
Signal Input: 1x Combo IN (XLR/Jack)
Signal Out: 1 XLR link OUT
USB connector: Yes – mini USB
Mechanics
Housing: Polypropylene PP reinforced by internal metal
structure
Grille: FULL / Invisible screws
Flyable: Yes
Handles: 1x on TOP / 1x on BOTTOM
Pole Mount: Yes, 36 mm
Width: 280 mm (11.02 in)
Height: 806 mm (31.73 in)
Depth: 393 mm (15.47 in)
Weight: 20.8 kg – 45.86 lbs.
User Interface: OLED display + push rotary encoder
Self-rotating display: yes
Positioning: EPD (Element Position Detection)
Display mirroring: Yes
Download the complete user manual on:
www.dbtechnologies.com/EN/Downloads.aspx
EMI CLASSIFICATION
According to the standards EN 55103 this equipment is designed and suitable to operate in E3 (or lower E2, E1) Electromagnetic environments.
FCC CLASS B STATEMENT ACCORDING TO TITLE 47, PART 15, SUBPART B, §15.105
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
WARNING: Make sure that the loudspeaker is securely installed in a stable position to avoid any injuries or damages to persons or properties.
For safety reasons do not place one loudspeaker on top of another without proper fastening systems. Before hanging the loudspeaker check
all the components for damages, deformations, missing or damaged parts that may compromise safety during installation. If you use the
loudspeakers outdoor avoid spots exposed to bad weather conditions.
Contact dB Technologies for accessories to be used with speakers. dBTechnologies will not accept any responsibility for damages caused by
inappropriate accessories or additional devices.
Features, specification and appearance of products are subject to change without notice.
dBTechnologies reserves the right to ake changes or i prove ents in design or anufacturing without assu ing any obligation to change
or i prove products previously anufactured.
Scan with your QR Reader
App to download the
co plete User Manual