De Raat 7205 User manual

Operating instruction Cawi lock 7205
Even though using this lock system is very easy, please read
these operang instrucons carefully and completely before
using the lock; this will help to avoid operang errors. These
instrucons refer to an electronic lock installed in a high-
security container such as a safe. The green LED will blink to
conrm each keypad entry. The me period between any two
entries may not exceed 20 seconds as otherwise all previous
entries will be cleared. The keypad could be supplied with two
dierend keypad prints.
1. Input of numerical acces code
for example: 3 2 7 9 6 1
2. Input of alpha-numeric acces code e.g. ROLF12
For example: 8 7 5 3 1 2
Cawi electronic
lock 7205
General Closing the electronic lock
Opening the electronic lock
Enter the six-digit combinaon set at the factory by pressing
buons 1 – 2 – 3 – 4 – 5 – 6 or enter your own six-digit
combinaon.
Please note: Press the C buon to correct your entry; in this case
the enre combinaon will have to be entered again. The green
LED will light for about 6 seconds to indicate that the lock has
been cleared for opening. At the same me, the electronic lock
will clear the mechanism for opening. The door to the safe can
now be unlocked with the keypad lever and opened using the
ngerp grip. The electronic locking element is then locked again
automacally aer about 6 seconds; this is indicated by the red
and green LEDs blinking once. The electronic lock is only secured
when the keypad lever is moved manually into its locked
posion.
Close the door to the safe and return the keypad lever to its locked
posion, moving it all the way to the mechanical stop. The red cap
must be completely concealed by the keypad lever. The green LED
goes out at the same me to indicate that the electronic lock has
been mechanically secured in this posion.
Please note: Try to operate the keypad lever to verify that the
container is closed correctly and securely.
Response to erroneous entries
If you press the C buon during the entry sequence, then the
enre series of digits previously entered will be cancelled. If a
programming phase has been iniated, then the lock will exit the
programming mode; you must re-start programming from the
very beginning by pressing the * buon.
Excepon: The me-out period following erroneous entries and
the low-baery warning period cannot be interrupted by
pressing the C buon.
The red LED lights for about 3 seconds whenever an invalid
combinaon is entered. The combinaon may now be entered
again. Aer the third consecuve incorrect entry, however, a 10-
second me-out period starts; the keypad will accept no entries
during this period. This me-out period will be extended by 10
seconds following each subsequent incorrect entry. The me-out
periods cannot be interrupted with the ”C” buon.
Correction with the C button

Programming the master combination
Monitoring the batterycharge level,
replacing the batteries
Programming the electronic lock
If the charge remaining in the baeries is insucient, then
the red and green LEDs will blink alternately 10 mes aer
the combinaon has been entered. This is to remind you to
install two new 1.5 Volt AA (alkaline) cells in the next few
days.
Note: If you ignore the low-baery warning over a longer
period of me, then you must be aware of the hazard that it
will be possible to open the lock and, as a consequence, the
safe only aer new baeries have been installed. The baery
compartment cover is located to the right of the keypad
housing. Remove the Phillips screw and then slide the baery
compartment cover carefully o of the keypad housing in the
direcon indicated by the arrow. See Figure 1. Remove the
exhausted baeries and replace them with two new 1.5 volt
AA (alkaline) baeries. The direcon in which the baeries
are to be installed is shown inside the baery compartment
cover. The programmed combinaon will be retained during
baery replacement.
Note: Program only with the door open and the electronic lock released. The green LED must not be lit
Before you use your safe for the rst me it is necessary, for
security reasons, to enter your personal combinaon; the
factory combinaon must not be retained. The lock should be
programmed only with the door open and with the electronic
lock released. Select your new six-digit combinaon before
starng the easy programming sequence. Do not use any
personal data for this combinaon, such as birthdays or other
informaon which could be derived from knowledge about your
person. Store your combinaon in a safe place so that only you
have access to it.
Note: We can assume no guarantee liability for malfuncons caused by erroneous reprogramming or applicaon of undue force or im-
proper treatment nor in case of injury to property or assets which, for example, is due to a failure to close the safe properly. We recom-
mend obtaining suitable insurance coverage to protect the contents of your safe. Your property insurance sales agent can provide de-
tails.
Troubleshooting in case of malfunction
If it is not possible to open your safe in spite of having carried out the instrucons above, then please contact the safe
manufacturer.