Tecnosicurezza Pulse Pro User manual

Pulse Pro
User Instructions

2 di 26 IU_PulsePro_08
User instructions
Pulse PRO
Company
Founded in 1983 with the aim of providing a complete range of professional products,
Tecnosicurezza is now a consolidated reality in the field of locks and security systems for safes.
The experience gained in over 35 years of activity in the security sector has allowed the
designing and manufacturing of high technology and reliability systems, which continue to
receive the approval of an increasingly demanding clientele.
TECNOSICUREZZA is present directly on the Italian, Spanish and US markets and, through a
extensive distribution network, in many EU and extra-EU countries.
TECNOSICUREZZA is aimed at national and international customers of primary importance,
such as banks, safe manufacturers, cash in transit companies, mass market retailers and post
offices.
Today TECNOSICUREZZA is a leading company focused on the customers’ needs and
constantly in step with technology.

IU_PulsePro_08 3 di 26
User instructions
Pulse PRO
Table of contents
COMPANY 2
TABLE OF CONTENTS 3
IMPORTANT NOTES! 5
GENERAL INFORMATION 6
OVERVIEW FUNCTIONS 9
LOCK OPENING 10
PRE-SETUP MODE 10
MANAGER AND STANDARD USERS 10
OVERRIDE USERS 11
CODE CHANGING (FUNCTION 0) 11
INSTALL/DISABLE/DELETE USERS 11
DISABLE/ENABLE USERS (FUNCTION 2) 12
DELETE USERS (FUNCTION 3) 12
BATTERY TEST (FUNCTION 4) 12
TEST MODE (FUNCTION 5) 12
LOCK SETUP (FUNCTION 6) 13
REMOTE OVERRIDE/REMOTE BLOCK 13
HOLD-UP/BOLT OUTPUT 13
DOOR ALARM 14
MANUAL CLOSING 14
BUZZER SILENT 14
DATE FORMAT 14
EXPIRING CODES 15
DELETION OF UNUSED CODES 15
USERS STATUS (FUNCTION 7) 15
AUDIT 16
DOWNLOAD THE AUDIT ON A DALLAS KEY 16
DOWNLOAD THE AUDIT ON PC: 16
CONFIGURATION SELECTION (FUNCTION 8) 17
TIME DELAY (FUNCTION 9) 18
TIME SETTING 18
DATE SETTING 19

4 di 26 IU_PulsePro_08
User instructions
Pulse PRO
EMERGENCY RESCUE CODE (ERC) 19
RESET MODE (WITH RESET BOX) 19
CONFIGURATION NUMBER 20
CONTACTS 26

IU_PulsePro_08 5 di 26
User instructions
Pulse PRO
Important notes!
•Before installing this product, please read carefully the installation and operating
instructions.
•Locks have been designed to correctly operate in a temperature range from -5°C to +
50°C and and in an environment with non-condensing humidity between 25% and 90%.
•The lock must not be oiled/lubricated/greased.
•If installed in normal domestic or office environments, the locks do not require
particular maintenance; in any case, after 10,000 opening/locking cycles, it is
recommended to run a test that verifies the correct and complete operation of the
product.
•Use only DURACELL™ 9 Volt Alkaline batteries, or battery holders with DURACELL™ 1.5
Volt Alkaline batteries. Alternatively, it is possible to use a 12VDC - 1A power adapter
(p.n. N1212) with relative power supply interface (p.n. T6005/W or p.n. T6005).
•A series of multiple beeps indicate a low battery level which need immediate replacing.
•It is strongly recommended to change the default codes before the usage and to keep
safely the new codes.
•Do never use codes easy to be guessed such as 123456, birth dates or others, based on
own personal information.
•After changing a code, perform several opening/closing tests before closing the door.
Should the lock label be removed, warranty is void.

6 di 26 IU_PulsePro_08
User instructions
Pulse PRO
General information
Using your keypad
The keypad automatically switches OFF if no buttons are pressed
within 5s.
Press to cancel an operation. A short beep is produced.
To start a time delay counting (if set), enter an opening combination:
LED flashes every 2s, indicating the counting.
Press to stop a time delay counting.
The open window is indicated by a flashing and a beep alternating at 1s
intervals.
The led is kept ON if the system is in programming mode.
2 short beeps are produced if an operation/ID/code is correct.
A long beep is produced if an operation/ID/code is incorrect.
If an incorrect operation is done, wait for 5s until the keypad switches
OFF before continuing.
A single beep (bad sound) is produced when some setup options of the
lock are enabled.
A long beep plus 3 shorts beeps are produced if an expired code is
entered.
An error beep is produced in case of RTC issue. It is recommended then
to update time and date.
!

IU_PulsePro_08 7 di 26
User instructions
Pulse PRO
To open or access the menu in dual mode (if set), enter the first user's
combination: the led flashes fastly. Then, enter the second user's
combination.
To stop a dual mode opening, press after having introduced the
first user’s combination and while the led is flashing.
Shortcuts
Press and hold for 2 seconds the button related to the needed function:
= Change Master code (80, 81), Manager (60, 61), users (01-59) and override users (10
or 50-59)
= Users installation
= Enable/Disable Users
= Delete Users
= Battery test
= Test mode
= System setup
= Users status and Audit
= Configuration selection/PC programming through setup software
= Time delay and opening window
= Time and date setting
= Reset

8 di 26 IU_PulsePro_08
User instructions
Pulse PRO
Pre-setup & Configurations
When the lock is in pre-setup mode and connected with the keypad for the first time, a long
series of short beeps plus 2 final short confirmation beeps are produced, to indicate that the
lock has been recognized.
In this mode:
•lock can be simply opened by pressing the button 1. When the bolt is open, the output
connector BAT is enabled;
•only the following options are allowed: Battery Test, Test mode, Date format,
Time and date setting and Configuration selection;
•time and date must be set before the usage otherwise a long beep is produced at every
opening.
WARNING: time and date values can be also entered in pre-setup mode, but only after
selecting the Date format.
Through the keypad, the lock can be set according one among the 80 different configurations,
involving the number of users, the dual mode opening and the Manager management. The PC
is not necessary!
Pulse PRO can be also used with analog locks such as EM2020, EM2050, EM3520, EM3520/S,
EM3550, EM3550/S and EM6050. If the keypad is connected with one of these locks, the
options enabled are only the ones corresponding to the locks properties, hence please refer to
the relative user manuals.
User properties and default codes
Users can be set for opening by entering their own combination created as:
- ID + numeric code;
- ID + numeric code + Dallas key;
- ID + Dallas key.
When programming, it is also possible to set a dual mode opening. Thus, it is necessary to
enter the combinations of the two users involved, in order to open the lock.
Default combinations used are of type ID + numeric code:
1st Master: 80-123456.
2nd Master: 81-123456 (available only for some configurations).
Master can change his code, change a configuration in dual mode with the Manager and set
also the time and date. In some configurations, Master can also manage Manager codes.
1st Manager: 60-123456
2nd Manager: 61-123456 (available only for some configurations).
Manager can perform openings, change his own code, change a configuration in dual mode
with Master, manage all the standard and override users, set a time delay, check a user
configuration and download the lock events. Manager cannot manage the Master code.

IU_PulsePro_08 9 di 26
User instructions
Pulse PRO
Users from 01 to 59: 01-010101, 02-020202 and so on. They always open with time delay if
set.
Override users: depending on the configuration selected, the number of override users can be
from one (10-101010) to 10 max. (from 50-505050 to 59-595959). They always open without
time delay.
ERC code (Emergency Rescue Code) is always built as ID + 8 digits.
1st ERC, random code provided by Tecnosicurezza: 98-98989898.
2nd ERC, random code provided by Tecnosicurezza: 99-99999999.
This user manual describes the standard programming. According such programming and
unless different requests while ordering the product, an opening can be performed by
entering single users codes (no dual mode) and without time delay. Thus, the user manual
must be adapted according the configuration selected.
It is strongly recommended to change the default codes before using the lock.
Overview functions
Lock opening
After entering an opening code, it is possible to open the lock within 3 seconds. It’s no
necessary instead with motorized locks: in this case indeed, the motor moves the bolt which
remains in opening position for about 8 seconds before returning in closing position. In the
manual closing version instead, the bolt can be closed by pressing key for few seconds.
Penalty
Four consecutive wrong codes initiate a four minutes penalty time. During this period, the LED
flashes once every 10s. Each time a key is pressed, a long beep is produced and no operation is
allowed.
Time Delay
Programmable time delay in between 0 and 99 minutes. Programmable open window in
between 1 and 19 minutes.
Dallas Keys
During the installation (function 1), a Dallas key (model 1982, 1990 or 1971) can be associated
to a user or a Manager (no Master) by simply placing it in the Dallas reader after entering the
ID and related code. The user is then identified by a combination built as ID + numeric code +
Dallas key. Multiple Dallas keys with same ID, can be programmed through PC and setup
software, in order to be used for particular applications. Please refer to the user manual
IU_PulsePRO_setup_XX for further information or contact Tecnosicurezza.

10 di 26 IU_PulsePro_08
User instructions
Pulse PRO
Power supply
Lock can be powered with:
•an ALKALINE 9V battery located in the battery compartement below the keypad;
•an internal battery box provided by Tecnosicurezza (6 ALKALINE 1.5 batteries);
•A power adapter (ref. N1212) with power supply interface (ref. T6005/W or T6005)
both provided by Tecnosicurezza.
Low battery warning
A series of multiple beeps indicates a low battery level which needs immediate replacing.
Audit
The lock is able to save the last 5500 operations with time, date, user and operations
description.
Users Status
The current status of the user can be checked through the function 7 when using the keypad.
IMPORTANT
Some options/characteristics reported in this user manual, can only be used if previously
enabled through the setup software. Thus, please refer to the user manual
IU_PulsePRO_setup_XX.
Please contact Tecnosicurezza for further information.
Lock opening
Pre-setup mode
Press to open the lock. 2 short beeps are produced.
Open the lock within 3 seconds.
Manager and standard users
Enter an opening combination. 2 short beeps are produced.
Open the lock within 3 seconds.
If a time delay is programmed, a short beep is produced and the led
flashes once every 2 seconds.
Press to stop the delay counting.
The opening window is indicated by a flashing and a short beep
alternating at 1 second intervals.