Dea Digipro Product manual

Digipro
Digislim
Access Control
Operating instructions and warnings
I66331X Rev. 01 26-05-14

9
Digipro - Digislim
Access Control
Operating instructions and warnings
Art. DIGISLIMArt. DIGIPRO
Technical data
Terms of use:
- temperature: -20°C ÷ +50°C
- RH: ≤95%
Current and voltage:
- DC input: +12V - +24V
- AC input: ~ 12V - 24V
- Standby current: ≤80mA
- Current while using: ≤110mA
Aplicable card mode:
- EM ID Card (Default)
Eective distance: 5cm
Storage capacity:
- ZONA 1: up to 1000 passwords AND cards
- ZONA 2: up to 10 passwords OR cards
N° Description
1 Mode indicator
2 Door indicator
3 Antenna
4 Keyboard
5 Lid screw

10
1 SPECIFICATIONS/FEATURES
•EM internal player.
•Frequency: 125KHz.
•Eective distance: 5cm.
•ZONE 1: up to 1000 passwords AND cards
ZONE 2: up to 10 passwords OR cards
•Access by card, access by code, combined access.
•Operating with digital keyboard.
•Integrated anti-removal function.
•Two relay outputs.
•Delay release time output: 0~99s.
•IP: 65.
•Dimensions:
DigiPro :120x76x28 mm.
DigiSlim :165x45x23,5 mm
•Two relay outputs for door opening, door status detection, door opening by key. Door
status detection regards ZONE 1 only.
2 INSTALLATION
Warning: Please remove the lid carefully following the instructions. Avoid removing parts by
forcing the components.
Warning: In order to remove the lid, slightly slide upward the front part, then following Fig. 1 ,
lift the lower part of about 20° and remove it gently.
Before installing, locate the position in which the access control will be mounted. Please
proceed according to the following instructions:
•Open the device by unscrewing and removing the special screw on the bottom of the rear
base with the wrench provided.
•Use the drilling template provided to locate the exact position and to drill the holes requi -
red.
•Use the screws provided to x the rear base to the wall. Be sure to run the cables through
the large hole in the center of the rear base ( Fig. 2 and Fig. 3 ).
•Run the wiring carefully following the label on the back ( Fig. 4 ).
•Reassemble the unit and secure it using the wrench.

11
3 OPERATING
ZONE 1 and 2 relays can be programmed to open the lock; you can store up to a maximum of
1000 user cards (AND their codes) for ZONE 1 and up to a maximum of 10 user cards (OR 10
codes) for ZONE 2. Moreover, ZONE 1 can be programmed in 3 modes to open the lock: access
by card (card only), by card or code (you can use the card or the code) and by combined access
(card and code together). ZONE 2 can be programmed for the bell.
3.1 Access to the setting mode
•Default admin code is 1234.
•Enter the default admin code 2 times (1234 - 1234). But:
a) if the default admin code entered is 2 digits, please insert 12 - 12;
b) if the default admin code entered is 3 digits, please insert 123 - 123;
c) if the default admin code entered is 5 digits, please insert 12345 - 12345;
The rest may be deduced by analogy and the maximum is 6 digits long.
•After entering the setting mode, the yellow LED lights up.
Warning: users codes must be dierent from administrator code.
Warning: ZONE 1 codes must be dierent from ZONE 2 ones.
3.2 Setting the access mode
In setting mode:
•Press followed by , the mode yellow LED blinks, press the
and you will hear a long beep. This indicates that you can get access by card only.
•Press followed by , the mode yellow LED blinks, press the followed by , the light
by code.
•Press followed by , the mode yellow LED blinks, press the followed by , the light
by code (combined access).
•Press to exit the setting mode.
3.3 Setting the length of passwords
In setting mode:
•Press followed by , the yellow LED blinks, press the followed by and you will hear
a “BI” as reminder, then digit X (X=2, 3, 4, 5, 6):
a) if 2 - Password/code length is 2 digits (from 00 to 99).
b) if 3 - Password/code length is 3 digits (from 000 to 999).
The rest may be deduced by analogy and the maximum is 6 digits long.
The “BI” sound, indicates that the chosen length value was correctly set.
If the sound is “BI BI BI”, indicates that the chosen length value is the same in use and can’t
•Press to exit the setting mode.
Warning:

12
3.4 Adding user card and code (ZONE 1)
In setting mode:
Insert a 3-digit number (from 000 to 999) corresponding to the data storage box in which you
want to operate, the yellow led blinks:
a) If the red LED is lit, it indicates that in the chosen memory box data is already saved, press
the key twice to clear the memory;
b) If the green LED is on, it indicates that cards and passwords can be added in the chosen
memory box.
Steps to add cards and passwords:
•In setting mode, the yellow LED blinks.
•Insert the 3-digit number (from 000 to 999) in the data storage box in which you want to add
the user, the green LED lights up.
•Approach the card, the sound “BI” indicates that it was added. Then insert the desired pas-
sword (relative to the just added card). The password length must be the same of the admin
code. For example, if the admin code is 12 (2 is the length) you have to set a 2-digit password
(from 00 to 99). if the admin code is 123 (3 is the length) you have to set a 3-digit password
(from 000 to 999). The rest may be deduced by analogy and the maximum is 6 digits long...
The “BI” sound, indicates that the password was correctly set.
•Press to exit the setting mode.
3.5 Erasing user card and code (ZONE 1)
In setting mode:
Insert a 3-digit number (from 000 to 999) corresponding to the data storage box in which you
want to operate, if the red LED is on, it indicates that in the chosen memory box data is already
saved, press the key twice to clear the memory.
3.6 Adding user card or code (ZONE 2)
In setting mode:
•Press followed by , the yellow led blinks, insert a 2-digit number (from 00 to 09) corre-
sponding to the data storage box in which you want to operate, the yellow LED blinks.
a) If the red LED is on, it means that inside the chosen memory box data is already saved,
press the key twice to erase the memory.
b) If the green LED is on, it means that cards o passwords can be added in the chosen data
storage box.
•Approach the card, the sound “BI” indicates that you added it; OR insert the desired pas-
sword; the password length must be the same as the admin code. I.g., if the admin code is 12
(2 is the length) you must set a 2-digit password (from 00 to 99). If the admi code is 123 (3 is
the length), you must set a 3–digit password (from 000 to 999). The rest may be deduced by
analogy...The sound “BI” indicates that the password was correctly set.
•Press to exit the setting mode.
3.7 Erasing user card or code (ZONE 2)
In setting mode:
Press followed by , the yellow LED blinks, insert a 2-digit number (from 0 to 09) correspon-
ding to the data storage box in which you want to operate, if the red LED is on it indicates that
in the chosen memory box data is already saved, press the key twice to erase the memory.

13
3.8 Relay timing
Relay timing for ZONE 1
In setting mode:
•Press followed by , the yellow LED blinks, digit the desired value (from 00 to 99), the
inserption of the relay activation time. The set value indicates the times the relay will be
active. For example:
a) Inserting 05, it means the relay will remain active for 5 seconds.
b) Inserting 00, you must approach the card o insert the password once to activate the relay
and a second time to close it.
•Press to exit the setting mode.
Door status detecting function (ZONE 1 ONLY): When someone opens the door and enter, and
the door is closed, the device automatically detects the door status and deactivates the relay
although this is still in the activation period.
Relay timing for ZONE 2
In setting mode:
•Press followed by , the yellow LED blinks, digit the desired value (from 00 to 99), the
inserption of the relay activation time. The set value indicates the times the relay will be
active. For example:
a) Inserting 05, it means the relay will remain active for 5 seconds.
b) Inserting 00, you must approach the card o insert the password once to activate the relay
and a second time to close it.
•Press to exit the setting mode.
3.9 Erasing all user cards and codes, restoring factory settings
In setting mode:
•Press followed by , the yellow LED blinks, press the key twice, you will hear a long
password) was cancelled correctly cancelled.
•Press followed by , the yellow LED blinks, press the key twice, you will hear a long
•Press to exit the setting mode and remain on standby.
Warning:
If you enter incorrect information, you will hear a double “BI-BI” and after 30 seconds the device
will automatically return to the initial mode again accompanied by the sound “BI-BI”.
If you’re not in the settings mode and you enter an incomplete number, or if you have to unlock
the door with the card and the password (combined) but only one of the two actions is made,
the device will return to the initial mode automatically after 5 seconds. accompanied by the
double sound “BI-BI”.
Warning:
If the admin code is lost, switch the power o, hold the key, then restore power. A sound “BI”
indicates that the default admin code was successfully reset.
If codes are 2 digits-the default admin code is 12;
If codes are 3 digits-the default admin code is 123;
If codes are 4 digits-the default admin code is 1234;
If codes are 5 digits-the default admin code is 12345;
If codes are 6 digits-the default admin code is 123456 (the maximum is 6).

14
In setting mode:
•Press followed by , the yellow LED blinks, then insert a new administrator code two
times (the admin code length must be the same as above): the sound “BI” indicates that the
•Press to exit the setting mode.
3.11 Turn on/turn o the anti-removal alarm
In setting mode:
•Press followed by (the yellow led blinks), then press followed by , a long “BEEP”
•Press followed by (the yellow led blinks), then press followed by , a long “BEEP”
•Press to exit the setting mode.
Warning: The built-in buzzer will continuously beep if the photoresistor is exposed to light. The
buzzer will automatically turn o within 60 seconds when the light is no longer detected, or by
entering the admin code.
3.12 Turn on/turn o the bell
In setting mode:
•Press followed by (the yellow led blinks), then press followed by , a long “BEEP”
•Press followed by (the yellow led blinks), then press followed by , a long “BEEP”
•Press to exit the setting mode.
Warning: The bell in ZONE 2 is available if the bell function is on. Press in standby mode, the
relay will active once, activating the bell.
Warning: If the bell is enable in ZONE 2, you can’t use cards or user codes.
3.13 Adding the master card (ZONE 1 only)
In setting mode:
•Press followed by , the green LED will blinks indicating that there are no master cards
stored, otherwise, if the LED turns red it means there is already saved data, press the key
twice to clear the memory, at this point the green LED blinks, then swipe the master card, a
long “beep” will be heard to indicate that the addition was successful.
•Press to exit the setting mode.
3.14 Enter settings mode swiping the master card
To enter the setting mode:
entry;
•To exit the setting mode, bring back the master card, the LED will turn green and you will hear
Warning: The access control will be locked for 60 seconds after entering a wrong code or the
swiping an invalid card for 5 times (both the keyboard and the card recognition won’t be available
during these 60 sec.).

15
3.15 Adding cards groups in ZONE 1
In setting mode:
•Press followed by (the yellow led blinks), then press followed by , a “BI” will be he-
ard as reminder. Insert a 3-digit number (from 000 to 999) corresponding to the data storage
(from 000 to 999 indicating the cards quantity that can be added. For example:
a) Inserting 005 060, it means that the cards added to the memory start from 005 and they
are 60.
b) Inserting 060 150, it means that the cards added to the memory start from 060 and they
are 150.
that the card was corectly added.
Warning:
set) will be automatically saved.
•Press to exit the setting mode.
3.16 Modifying the user code of ZONE 1
In setting mode:
•Press followed by (the yellow led blinks), then press followed by , a “BI” will be
heard as reminder. Insert a 3-digit number (from 000 to 999) corresponding to the data
storage box where you want to add a new password (the password length must be the same
as the admin code).
•Press to exit the setting mode.

16

57
Warning: In order to remove the lid, slightly slide upward the front part, then following Fig. 1, lift the
lower part of about 20° and remove it gently.
Sollevare - Lift -
Soulever -
Levantar -

58
N° Description

59
N° Description

60
ZONE 2
ZONE 1
Door status detecting

61
N° Color of wires Description
1Red
2Black
3Brown Door status detecting
4Orange
ZONE 1 activation key
5Yellow ZONE 2 activation key
6Green Grounding
7White N.O. 1
8Pink COM 1
9Light green N.C. 1
10 Blue N.O. 2
11 Purple COM 2
12 Gray N.C. 2
13 Black/White
Unused
14 Brown/White
15 Silver (shield) Shielded ground
ZONE 2
ZONE 1

Exclusive Australian Distributor
Customer Service [phone]
See downee.com.au for your state office
Tech Support 1800 241 733 [e-mail]
downee.com.au
deasystem.com