Decon wheel Helium User manual

2021-12-22
Assembly instructions for Helium, Nitrum (Not Pro rear axle)
MED3348
For Std rear axle
1. Remove wheels on both sides.
2. Remove the sleeve buy loosen the screw 1 and pull out the sleeve 2.
3. Check the correct placement for the stop pin and check that MED1510 is mounted.
MED1510
MED1510
5
5
Only STD rear axle.
Not PRO rear axle or
short COG rear axle.

2021-12-22
4. Assembly the plate (right side) according to picture.
Parts pair mountingset:
Item No. Part Number Qty Description
1 HW087 1 Wheel Hub
2 MED2000 1 Bracket
3 XSM8X16 1 Screw Round - M8 x 16
4 XSTM6X12 1 Stop Screw - M6 x 12
5 MED1510 1 Handle
5. First you take stop screw 7 and add Loctite onto the screw. Place the screw in the Hub
sleever 1, only aprox. 1-1,5 mm will be left of the head. Now you can try it in the rear
axle tub, adjust the stop screw if hub sleever is not fit in the tube or if the hub sleever
is turning.
Only STD rear axle.
Not PRO rear axle or
short COG rear axle.

2021-12-22
6. Adjust the gap to 2-3 mm for the rear axle according to the picture above. When you
have the right gap tighten the rear axle screw or screws 1 on both sides, when the hub
sleeve is so far in as possible. Now you can assemble the rest of the parts and
remember to use Loctite on all screws.





















1
Only STD rear axle.
Not PRO rear axle or
short COG rear axle.

2021-12-22
For Short COG rear axle
1. Remove wheels on both sides.
2. Remove the sleeve buy loosen the screw 1 and pull out the sleeve 2.
3. Kontrollera att stopp pinnen sitter enligt bilder ovan.
Only short COG rear axle.
Not PRO rear axle or STD
rear axle.
1
2

2021-12-22
4. Montera nu fästet se bilderna ovan som visar montering av fästet på höger sida.
För montering på en sida, så skall följande ingå.
Item No. Part Number Qty Description
1 HW087 1 Sleeve
2 MED2000 1 Bracket
3 XSM8X16 1 Screw Rounded M8 x 16
4 XSTM6X12 1 Stop Screw M6 x 12
Only short COG rear axle.
Not PRO rear axle or STD
rear axle.

2021-12-22
MED1674
Item No. Part Number Qty Description
1 XOD-2612E-00 2 Clamp
2 XA2-2612K-00 2 Clamp with thread
3 XSM6X35 2 Screw Round M6 x 35
4 X0C-48160-D0 1 Swing Away Bracket

2021-12-22
MED1675
Item No. Part Number Qty Description
1 XOD-2612E-00 2 Clamp
2 XA2-2612K-00 2 Clamp with thread
3 XSM6X30 2 Screw Round M6 x 30
4 MED1320 1 Bracket
5 X0F-48160-D00 1 Parallel Bracket

2021-12-22
MED1676
Item No. Part Number Qty Description
1 XSM6X16 1 Screw - Round - M6 x 16
2 XSM6ML 2 Locknut M6
3 XSM6X12 1 Screw - Round - M6 x 12
4 XSM6BR 1 Plain Washer M6
5 MED1500 Rev6 1 Bracket
6 X0C-48160-D0 1 Swing Away Bracket

2021-12-22
MED1677
Item No. Part Number Qty Description
1 XSM6X16 1 Screw Round M6 x 16
2 XSM6ML 2 Locknut M6
3 XSM6X12 1 Screw Round M6 x 12
4 XSM6BR 1 Plain Washer M6
5 MED1500 Rev6 1 Bracket
6 X0F-48160-D00 1 Parallel Bracket

2021-12-22
Brake adjustment
Item No. Part Number Qty Description
1 XSM6X70 2 Screw Round M6 x 70
2 XSM6ML 2 Locknut M6
3 100 400 044 2 Spacer
QR-axle set for standard wheels (Not Included)
Item No. Part Number Qty Description
1 QR1272 1 QR axle
2 100 400 113 1 Spacer
3 93440-120520 1 Circlip
3
1
2

2021-12-22
Om inget annat specificeras, använd följande åtdragningsmoment.
Unless otherwise specified, use the following tightening torque.
Metriska grovgängor, stål.
Metric coarse threads, steel.
Gänga / Thread Åtdragningsmoment / Tightening torque
M3 1,2 Nm
M4 3 Nm
M5 6 Nm
M6 10 Nm
M8 25 Nm
M10 50 Nm
M12 85 Nm
Navhylsor.
Sleeve.
Gänga / Thread Åtdragningsmoment / Tightening torque
M16x1 30 Nm
M18x1 40 Nm