Dell 3130cn - Color Laser Printer User manual

Dell 3130cn
Service Manual
21 Aug 2009

Information in this document is subject to change without notice.
2010 Dell Inc. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Dell Inc.is strictly forbidden.
Trademarks used in this text: Dell and the DELL logo are trademarks of Dell Inc.
Other trademarks and trade names may be used in this document to refer to the entities claiming the marks and
names of their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than
its own.

Version record
Refer to the portion indicated by change bar in each section.
Also refer to the reasons in table below.
Version Issue date Note
1st February 15, 2008 1st issued
2nd
March 27, 2008
2nd version issued
Section 1, FIP
1. Rewrote contents
1.1 to 1.5
2.3 terminological corrections etc.
3.1 additional flows and terminological correction
etc.
Flows 1 to 5/8 to 10/12 to 20/22 to 23/25/27 to
29/31 to 32/34 to 35/38 to 39/45 to 58/60 to
62/64/66 to 69/71 to 90/92 to 98 corrected
FIP-1.1 to 1.4/1.9 to 1.10/1.12 to 1.13/1.19 to
1.20/1.35/1.45/1.50/1.71/1.73 corrected
Flows67 to 69 added
4.1 illustration changed and table changed
4.3 terminological corrections etc.
FIP-1.P1 to 1.P15 terminological corrected
FIP-1.N1/1.N3 terminological corrected
3rd
May 30, 2008
3rd version issued
Section 1, FIP
1.5 Consumables life information added.
2.3 Expression of an error message has been
improved. etc.
3.1 Supplementary explanation etc. was added.
Flows11/FIP1.11 deleted.
Flows22/32/57/61 supplementary sentence
added.
Flows5/8/23/24/45/63 to 69 flows improved.
Flows30/46 to 52/58/60/62/75/76
Supplementary sentence added. And flow
improved.
Flows78 to 92 illustrations added.And
supplementary sentence added.
Section 2, Operation of Diagnostic
1.2/2.2 Name corrected.
4.1.2 /4.1.3/6.2/6.3 Illustration changed etc.
4.5.13 /6.9.2 Parameter value corrected etc.
5./ 6. Name corrected.
5.3 PC screen changed etc.
5.4 Name corrected etc.
5.6 Menu corrected.
6.1 Explanation of IOT Test added.
6.6 Clerical error corrected.
6.7 Clerical error corrected.

6.9.9 Counter value corrected.
Section 3, Removal and Replacement Procedure
1.1 Illustration changed.
1.2 Illustration changed.
2. Illustration changed etc.
Removal 1/3～8/ 10～15/17/ 20～26 / 28/ 31/
33～34/ 37～38/40～44/47～50 Illustration
changed etc.
Removal 36 Procedure changed. /Illustration
changed.
3. Illustration changed.
Replacement 1～4/6～7/10～11/13/16/18/20～
24 /27/29～34/36～41/43/46～50 Illustration
changed etc.
Replacement 8 Procedure changed. /
Illustration changed.
Section 4, Plug/Jack(P/J) Connector Locations
1.2 Illustration changed.
Section 5, Parts List
1.2 Illustration changed.
PL1.1/ PL2.1/ PL2.2/ PL3.2 / PL7.1/ PL8.1/
PL12.3 Illustration changed.
PL1.2/ PL3.1/ PL5.1/ PL6.1/ PL9.1/ PL10.1 List
changed/ Illustration changed.
PL12.2 Clerical error corrected.
Section 6, Principles of Operation
1.1 Illustration changed.
1.2 Illustration changed.
1.3.6 Neutralization deleted.
1.3.6 Paragraph number changed.
3.1.2/ 3.1.4 / 3.1.5 / 3.2.1 / 3.2.2 / 3.3.1 / 3.3.2 /
3.4.1 / 3.4.2 / 3.5.2 / 3.6.1 / 3.6.2 / 3.7.2 / 3.8.2
6.1 / 6.4 Illustration changed.
Section 7, Wiring Diagrams and Signal
information
2.2 Name corrected.
2 MSI&REGI Connector pin number corrected.
3 DRIVE Diagrams Clerical error corrected.
Section 8, Printer Specifications
1.1 / 3.1 / 3.4 / 3.5 / 5.3 Illustration changed.
7.2/9.1/10.1.4/10.2.2/10.5.3/10.8.1 corrected.
9.1 Option added.
10.1.4 “Supported Client” added.
10.2.1 “FTP Protocol” deleted.
10.2.2 Supplementary sentence added.
10.5.3/10.8.1 Clerical error corrected.
4th
December 17, 2008
4th version issued
Section 1, FIP
3.1 The procedure was added.
Flows 46 to 49/79

4.1 Flow changed
4.1th
April 08, 2009
4.1th version issued
Section 1, FIP
.
Flows25-1and Flows99 are added.
(Change by error code (016-340).)
4.2th
August 12, 2009
4.2th version issued
Section 1, FIP
.
Flows25/FIP1.25:
The flow of 016-317 and 016-340 was
corrected.
Flows31/FIP1.31:
The up-loading of Firmware was added.
4.3th
August 21, 2009
4.3th version issued
Section 1, FIP
.
Flows25/FIP1.25:
The download procedure of FW by the download
mode was added. (Only 016-317 )
Flows25-1:NEW
The download procedure of FW by the download
mode was newly added. (016-340 )
Flows31/FIP1.31:
The download procedure of FW by the download
mode was added. (016-370 )

i
Version 1 2007.12.28
Cautions
Operation contents of this document may be subject to modification without notice.
'HOO,QF will not assume responsibility for accidental or incidental damagesUHVXOWLQJIURPWHFKQLFDO
or editorial errors or omissions in this manual, the issue of this manual, theH[HFXWLRQRIGHVFULSWLRQV
in this manual, or the use of this manual.
This document is protected by copyright. Do not photocopy or duplicate any part of this document in
any form without written permission from 'HOO,QF

ii
Version 1 2007.12.28
1. About this manual
This manual is a standard service manual of 'HOO,QF containing information UHTXLUHGIRUPDLQWHQDQFH
maintenance of this laser printer (standard specifications).
2. Marks giving caution
Maintenance operations requiring special cautions or additional information regarding descriptions in
this manual are presented as "Warning," "Caution," or "Note," depending on their nature.
If instructions are not observed, death or serious injury may result.
If instructions are not observed, injuries to workers or physical damage to assets
(including this laser printer) may result.
Essentials for procedures, steps, rules, and others.
Reference Incidental information to descriptions.
3. Related documents
-Instruction manuals (standard manuals)
Describe the operation and handling of this laser printer.
-Performance specifications
Describe in detail various specifications of this laser printer.
(In the event of a discrepancy between this manual and the performance specifications, the
performance specifications take precedence.)
-Spare parts list
Information on maintenance parts (spare parts) for this laser printer.

iii
Version 3 2008.05.30
4. Safety
To prevent possible accidents during maintenance operation, you should observe strictly the "Warning"
and "Caution" information in this manual.
Avoid dangerous operations and operations out of the scope of this manual.
Various processes not covered by this manual may be required in actual operations, and should be
performed carefully, always giving attention to safety.
4.1 Power source
Keep the power plug disconnected during the maintenance operation to prevent electric shock, burns
and other damages.
If the power supply should be kept connected to measure voltage or for other similar reasons, take
sufficient care to prevent electric shock, by following the procedures in this manual.
While the printer is on, never touch live parts if not required.
Power is supplied to the power switch / inlet even while the printer is off. Never
touch its live components.
Do not touch live parts unless otherwise specified.
Zna00002KA

iv
Version 1 2007.12.28
4.2 Driving units
When servicing gears or other driving units, be sure to turn off the power switch and unplug the power
cord. Drive them manually when required.
Do not do the print work removing the cover of the printer to confirm the operation
of driving part.
4.3 High-temperature units
When servicing high-temperature units (securing unit, etc.), be sure to turn them off to prevent burns,
injuries and other troubles. Remove the power plug and start service processes after they have cooled
down sufficiently.
Because high-temperature units are still hot after they complete an operation, wait
at least 40 minutes before starting maintenance service.

v
Version 3 2008.05.30
4.4 Laser beams
• If your eyes are exposed to laser beams, you may lose your eyesight.
• Never open the cover if the warning label for laser beams is attached there.
• Before disassembling and reassembling this laser printer, be sure to turn it OFF.
• When servicing this laser printer while it is running, be sure to follow the
procedures specified in this manual.
• You should be well aware that the laser beams are capable of injuring you and
other people near the printer.
Laser beams have features as follows:
• Frequencies are smaller in width than other beams (sun and electric bulbs) and
phases are uniform so that high monochromatic and convergence performance
can be obtained and thin beams of light can reach places at a long distance.
• Being highly converged, the laser beams exert a heating action that may be
harmful to human body.
Reference: The laser beams of this laser printer are invisible rays.
Zna00003KA
PRINT HEAD