
5
Before installing the unit , make sure of the following:
a. The appliance must not be located directly beneath a
current outlet.
b. The plug and outlet must be easy to reach after
installation.
c. No electric cables or other pipes could be damaged
during the installation.
d. Keep away from curtains or ammable materials.
To wall-mount, proceed as follows:
Turn the appliance upside down on a at stable surface. Using a
screwdriver, x the 2 brackets (G) with the 2 screws (H) as shown in
Fig. 2. For brick walls use a 6 mm concrete drill bit.
For plaster board or false (hollow) walls, it is recommended to use
appropriate screws and anchors (not supplied).
1. Before drilling the wall, mark the exact points, respecting the
minimum distances as shown in g. 3.
2. Drill the wall where previously marked, and insert the plastic
anchors (J).
3. Fix the 2 metal brackets (G) using the two screws (I) provided.
4. Hang the appliance on the bracket.
5. Mark out the 2 lower xing points. Remove the appliance, drill
the lower holes and insert the wall anchors (J).
6. Now, you can hang back the heater on the bracket and x the
lower part of the appliance with the 2 remaining screws (I).
USE
Operation and use
Plug into the mains, turn the thermostat dial to maximum (position
6) and turn the appliance on by means of the power selector as
described below:
• Turn the power selector knob to the Min position to select
minimum power.
• Turn the power selector knob to the Med position to select
medium power (only in some models).
• Turn the power selector knob to the Max position to select
maximum power.
• Turn the power selector knob to the Max position to select
maximum power with the fan (the MAX + FAN indicator light
comes on).
• To turn the appliance o completely: turn the power selector
to the "0" position and the thermostat to the " " position,
then unplug from the mains.
Adjusting the thermostat
When the room has reached the required temperature, turn the
thermostat dial slowly anticlockwise until you hear a click and no
further.
The thermostat will automatically regulate the temperature set and
keep it constant. In spring or autumn or on mild days, you can save
energy by using minimum power.
Frost prevention mode
With the thermostat dial in the position and one of the power
levels selected, the appliance maintains room temperature at about
5°C, preventing freezing with minimal energy consumption.
Models with ventilation
The appliance has 2 fans for faster more even heating. To start this
function, turn the power selector to Max .
Models with 24 hour timer
When the appliance is plugged to the mains the timer is always
in turning movement, in order to stay synchronized with the local
time. To operate the appliance without the timer, place the timer
slider in the position. To operate the appliance at set times,
position the slider in the position and proceed as follows:
• Check the time on your clock or watch. If it is 10.00 for example,
turn the numbered programmer disk until the number 10
coincides with the pointer marked on the programmer.
• Set the periods of time during which you want the appliance
to operate by pushing the teeth outwards. Each tooth
corresponds to a period of 30 min. At the end of this procedure,
sectors corresponding to the operating periods can be seen.
• In this way, the appliance will function automatically each day
at the times set. (Important: the appliance must always be
plugged into the socket)
• To modify programming, return the teeth to the initial position
and set the new operating periods.
• To turn the appliance o, turn the power selector to the "0"
position.
MAINTENANCE
Before carrying out any maintenance, unplug the heater from the
mains and wait for it to cool o completely. This heater requires no
particular maintenance. It is sucient to remove the dust with a
soft, dry cloth. Never use abrasive powders or solvents. If necessary
remove concentrated areas of dirt with a vacuum cleaner.
TECHNICAL CHARACTERISTICS
Supply voltage See rating label
Absorbed power “