Delta Children 76303 User manual

3 Drawer Dresser
Style #:
Lot:
Date:
76303
___________
___________
Jun 20, 2014 25101-76303-R0 ©2014 DELTA ENTERPRISE CORP.
Consumer Care:
www.DeltaChildren.com
Delta Children’s Products
114 West 26th Street
New York, NY 10001
Tele.212-645-9033
REV
THIS PRODUCT IS NOT INTENDED FOR
INSTITUTIONAL OR COMMERCIAL USE.
Read all instructions before assembly and use.
KEEP INSTRUCTIONS FOR FUTURE USE.
ADULT ASSEMBLY REQUIRED
Due to the presence of small parts during assembly, keep out of
reach of children until assembly is complete.
When contacting Delta Consumer Care please reference the above information. Before contacting Delta
Consumer Care please ensure that the information above matches the information found on the label on
the Back Panel.please reference the information found on the product when contacting Delta Consumer
Care.
To register your product for important safety alerts and updates to your product please visit
www.DeltaChildren.com and click on Product Registration.
A

Serious or fatal crushing injuries can occur from furniture tip-over. To help prevent tip-over:
.Place heaviest items in the lowest drawers.
.Unless specifically designed to accommodate, do not set TV’s or other heavy objects on the top of this
product.
.Never allow children to climb or hang on drawers, doors,or shelves.
.Never open more than one drawer at a time.
Use of tip-over restraints may only reduce, but not eliminate, the risk of tip-over.
.Always monitor your child’s activity when in the nursery.
.Do not allow standing in drawers.
.Do not allow standing on top of this product.
.Accessory Items must be securely fastened to this product according to the instructions provided with
those items.
.To avoid head injury, do not allow children to play underneath open drawers.
.Do not leave drawers open when not in use.
NOTES ON ASSEMBLY:
-During the assembly process whenever using screws or bolts, check each by placing the screw/bolt on the
diagram of the item which is drawn actual size and design. Be sure to use the proper size and shape specified in
the instructions.
-To assemble this unit you may be required to place the unit on it’s side and face. It is strongly recommended that
assembly is done on a soft, non-abrasive surface to avoid damaging the finish.
NOTES ON CARE AND MAINTENANCE:
- Do not scratch or chip the finish.
- Inspect the product periodically, contact delta children's products for replacement parts or questions.
- Do not store the product or any parts in extreme temperatures and conditions such as a hot attic or a damp,
cold basement. These extremes can cause a loss of structural integrity.
-To preserve the luster of the high quality finish on your product, it is recommended to place a doily or felt pad
under any items you place on the finish.
-Clean with a damp cloth, then a dry cloth to preserve the original luster and beauty of this fine finish.
-Do not use abrasive chemicals.
-Do not spray cleaners directly onto furniture.
-Lift slightly when moving on carpeting to prevent leg breakage.
-Use of a vaporizer near furniture will cause wood to swell and finish to peel.
WARNING
2

PARTS: HARDWARE KITS PART #25100
K. Drawer Bottom x3
Part #25098
N. Top Drawer Front x1
Part #25094
L. Drawer RightSide x3
Part #25096
M. Drawer Left Side x3
Part #25095
S. Drawer Support x3
Part #25099
R. Drawer Back x3
Part #25097
P.Lower Drawer Front x2
Part #25158
A.Left Side x1
Part #25085
B. Right Side x1
Part #25086
C. Top x1
Part #25093
D.Top Front Rail x1
Part #25087
E. Top Back Rail x1
Part #25088
J. Bottom Back Rail x1
Part #25090
G. Drawer rail x2
Part # 25091
F. Bottom Front Rail x1
Part #25089
H. Back Panel x1
Part #25092
3

PARTS: MAKE SURE THAT ALL PRE-ASSEMBLED PARTS ARE TIGHT.
AA. 30mm Bolt x4 BB. 40mm Bolt x 8
CC. 75mm Bolt x 10
DD. Barrel Nut x 10
JJ. 6mm Dowel x 6 KK. 8mm Dowel x 8
MM. Knob And Screw X6
Part# 25102
MM1
MM2
HH. Screw X20
GG. Drawer Screw X15
FF. Drawer Screw X 15
EE. Plastic Barrel Nut X 15
M4 Ball End Hex Wrench x1
No drills necessary.
Do not use power
screwdriver.
Flat Head Screwdriver
(not supplied)
Phillips Screwdriver
Not Included
4

This page is intentionally blank
5

KK. 8mm Dowel x 2
CC. 75mm Bolt x 5
DD. Barrel Nut x 5
A. Left Side x1
D. Top Front Rail x1
E. Top Back Rail x1
J. Bottom Back Rail x1
F. Bottom Front Rail x1
STEP 1:
Attach the Back Bottom Rail (Part J), Top Front Rail (Part D), Top Back Rail (Part E), and
Bottom Front Rail (Part F) to the Left Side (Part A) using (2) Dowels (Part KK),
(5) 75mm Bolts (Part CC) and (5) Barrel Nuts(Part DD).
Use the Flat Head Screwdriver to Hold the Barrel nuts in Propper allignment and tighten with
the M4 Hex Wrench.
6

A
J
F
D
E
CC
CC
CC
CC
CC
DD
DD
DD
DD
KK
DD
CC
7

G. Drawer rail x2
STEP 2:
Insert the (2) Drawer Rails (Part G) as shown with the rounded edges facing
the front.
8

G
G
9

STEP 3:
B. Right Side x1
CC. 75mm Bolt x 5
DD. Barrel Nut x 5
KK. 8mm Dowel x 2
Insert (2) Dowels (Part KK) into the Back Bottom rail. Align the Right Side (Part B)
With The Dowels and Rails. Attach the Side using (5) 75mm Bolts (Part CC) and
(5) Barrel Nuts (Part DD).
Use the Flat Head Screwdriver to Hold the Barrel nuts in Propper allignment and tighten with
the M4 Hex Wrench.
10