Delta Electronics SFP Bi-Directional Transceiver Module... User manual

SPBD-155F4J1R
DELTA ELECTRONICS, INC.
1 Revision: S1
09/20/2006
www.deltaww.com
SFP Bi-Directional Transceiver Module for Fast
Ethernet, ATM, SONET OC-3/SDH STM-1
FEATURES
 RoHS compliant

SFF-8472 MSA compliant

Simplex LC connector
 1550nm Transmitter, 1310nm Receiver
 Single + 3.3V power supply and TTL logic
interface
 Commercial and Industrial temperature
available

Bellcore GR-468 compliant
 Laser class 1 product which comply with the
requirements of IEC 60825-1 and IEC 60825-2
Description
The SPBD-155xxxx series are hot pluggable
3.3V Small-Form-Factor (SFP) Bi-Directional
transceiver module designed expressly for
high-speed communication applications that
require rates of up to 155Mbit/sec. It is compliant
with the Fast Ethernet, ATM, SONET OC-3/SDH
STM-1 standards, as well as the SFP
Multisource Agreement (MSA).
The SPBD-155xxxx transceivers provide with
the LC receptacle that is compatible with the
industry standard LC connector. The transceiver
is also compatible with industry standard RFT
connector and cage. It also includes a LOS
(Loss Of Signal) circuit that provides a TTL
logic-high output when an unusable optical
signal level is detected.
The module includes 1550nm un-cool FP laser,
InGaAs PIN, Preamplifer and WDM filter in a
high-integrated optical assembly for high-density
system application. The SFP Bi-Directional
transceiver can upgrade transmission capacity
very convenient without installing new fibers.
Application
 TTC TS-1000
 IEEE 802.3ah 100BASE-BX
 SONET OC-3/SDH STM-1
 FTTx WDM Broadband Access
 100Base Fast Ethernet
Performance

SPBD-155F4J1R data link up to 15km in
9/125um single mode fiber.

SPBD-155F4J1R
DELTA ELECTRONICS, INC.
2 Revision: S1
09/20/2006
www.deltaww.com
1. Absolute Maximum Ratings
Parameter Symbol Min. Typ. Max. Unit Note
Storage Temperature Ts -40 85 ºC
Operating Ambient Temperature Ta -10 80 ºC
Storage Ambient Humidity HA5 95 %
Power Supply Voltage VCC 0 5 V
Signal Input Voltage -0.3 Vcc+0.3 V
Optical Input Power (Peak) 4 dBm
2. Recommended Operating Conditions
Parameter Symbol Min. Typ. Max. Unit Note
Ambient Operating Temperature TA0 70 ºC
Ambient Humidity HA5 85 %
Non-condensing
Power Supply Voltage VCC 3.135 3.3 3.465 V
Power Supply Current ICC 250 mA
Power Supply Noise Rejection 100 mVp-p 100Hz to 1MHz
Data Rate 10 155.52 Mbps
Transmission Distance 15 km
3. Specification of Transmitter
Parameter Symbol Min. Typ. Max. Unit Note
Average Launched Power PO-14 -8 dBm Note (1)
Optical Extinction Ratio ER 10 dB
Center Wavelength λC1480 1520 1580 nm FP Laser
Spectrum Width (RMS) σ3 nm
Transmitter OFF Output Power POff -45 dBm
Optical Rise/Fall Time tr/tf1.3 ns Note (2)
Total Jitter TJ 1 ns Note (3)
Optical Return Loss Tolerance ORLT 14 dB
Relative Intensity Noise RIN -116 dB/Hz
Dispersion Penalty TDP 1 dB
Output Eye Mask Compliant with Bellcore TR-NWT-000253
and ITU recommendation G.957 Note (4)
Note (1). Launched power (avg.) is power coupled into a single mode fiber.
Note (2). These are unfiltered 20-80% values.
Note (3). Measure at 223-1 NRZ PRBS pattern.
Note (4). Eye Mask definition

SPBD-155F4J1R
DELTA ELECTRONICS, INC.
3 Revision: S1
09/20/2006
www.deltaww.com
4. Specification of Receiver
Parameter Symbol Min. Typ. Max. Unit Note
Input Optical Wavelength λIN 1260 1360 nm PIN-PD
Receiver Sensitivity PIN -31 dBm Note (1)
Input Saturation Power (Overload) PSAT -3 dBm
LOS-Deassert Power PA- -32 dBm
LOS-Assert Power PD-44 dBm Note (2)
LOS Hysteresis PA-PD0.5 2 5 dB
Optical Reflectance -14 dB Note (3)
Output Data Rise/Fall time tr/tf1.5 ns Note (4)
S/X Endurance 10 dB Note (5)
Optical Isolation 25 dB Note (6)
Note (1). Measured with 1520nm, ER=10dB; BER =<10-10@PRBS=223-1 NRZ
Note (2). When LOS asserted, the data output is Low-level (fixed)
Note (3). When the terminal is viewed from the optical path, the reflection toward the optical path of the
optical signal with a central wavelength of 1260nm to 1360nm transmitted to terminal.
Note (4). These are 20%~80% values
Note (5). X=10 MHz, Rectangular BER =10-10
Note (6). Receiver isolation between 1480nm ~1580nm
0.85
1.20
0.80
1.00
0.50
0.20
0.00
-0.20
Amplitude
0.350.150.00
Time
0.65
Mean level of logical "0"
1.00
Mean level of logical "1"
Opt
i
ca
l P
u
l
se
M
as
k
w
i
t
h B
esse
l Fil
te
r
Spec
ifi
ed
in IT
U
-T
G.957

SPBD-155F4J1R
DELTA ELECTRONICS, INC.
4 Revision: S1
09/20/2006
www.deltaww.com
5. Electrical Interface Characteristics
Parameter Symbol Min. Typ. Max. Unit Note
Transmitter
Total Supply Current ICC A mA Note (1)
Differential Data Input Swing VDT 500 2400 mVp-p
Differential line input Impedance RIN 80 100 120 Ohm
Data Input Voltage- High VIH-VCC -1.165 -0.880 V
Data Input Voltage- Low VIL-VCC -1.810 -1.475 V
Transmitter Disable Input-High VDISH 2 VCC V
Transmitter Disable Input-Low VDISL 0 0.8 V
Transmitter Fault Output-High VTXFH 2 VCC+0.3 V
Transmitter Fault Output-Low VTXFL 0 0.8 V
Transmitter Fault Pull up Resistor RTX_FAULT 4.7 10 kNote (2)
Receiver
Total Supply Current ICC B mA Note (1)
Differential Data Output Swing VDR 400 2000 mVp-p Note (3)
Data Output Voltage-High VOH-VCC -1.085 -0.880 V
Data Output Voltage-Low VOL-VCC -1.830 -1.555 V
LOS Output Voltage-High VLOSH 2 VCC+0.3 V
LOS Output Voltage-Low VLOSL 0 0.8 V
Receiver LOS Load RRXLOS 4.7 10 kNote (2)
Note (1). A (TX)+ B (RX) = 250mA (Not include termination circuit)
Note (2). Pull up to VCC on host Board.
Note (3). Internally AC coupled, but requires a 100Ohm differential termination at or internal to Serializer/
Deserializer.
6. Timing of Control and Status I/O
Parameter Symbol Min. Max. Unit Unit Conditions
TX_DISABLE Assert
Time t_off 10
µsec
Time from rising edge of TX_DISABLE to
when the optical output falls below 10% of
nominal
TX_DISABLE
Negate Time t_on 1 msec
Time from falling edge of TX_DISABLE to
when the modulated optical output rises above
90% of nominal
Time to initialize,
including reset of
TX_FAULT
t_init 300 msec From power on or negation of TX_Fault using
TX_Disable.
TX_Fault Assert Time t_fault
100 µsec Time from fault to TX_Fault on.
TX_DISABLE to
reset t_rest 10
µsec Time TX_Disbale must be held high to reset
TX_Fault
LOS Assert Time t_loss_on 100 µsec Time from LOS state to Rx LOS assert
LOS Deassert Time t_loss_off 100 µsec Time from non-LOS state to Rx LOS deassert
Serial ID Clock Rate f_serial_clock 100 kHz

SPBD-155F4J1R
DELTA ELECTRONICS, INC.
5 Revision: S1
09/20/2006
www.deltaww.com
Timing Parameters Definition
Power on initialization of SFP transceiver, TX_DISABLE
negated
Power on initialization of SFP, TX_DISABLE asserted
Initialization during hot plugging of SFP TRANSCEIVER.
Example of initialization during hot plugging, TX_DISABLE
negated.
SFP TX_DISABLE timing during normal operation.
Detection of transmitter safety fault condition Successful recovery from transient safety fault condition
Unsuccessful recovery from safety fault condition Timing of LOS detection

SPBD-155F4J1R
DELTA ELECTRONICS, INC.
6 Revision: S1
09/20/2006
www.deltaww.com
7. Pin Description
SFP Transceiver Electrical Pad Layout Host Board Connector Pad Layout
Pin Function Definitions
Pin Num. Name Function Plug Seq. Notes
1 VeeT Transmitter Ground 1 Note (1)
2 TX Fault Transmitter Fault Indication 3 Note (2)
3 TX Disable Transmitter Disable 3 Note (3)
4 MOD-DEF2 Module Definition 2 3 Note (4), 2 wire serial ID interface
5 MOD-DEF1 Module Definition 1 3 Note (4), 2 wire serial ID interface
6 MOD-DEF0 Module Definition 0 3 Note (4), Grounded in Module
7 Rate Select Not Connect 3 Function not available
8 LOS Loss of Signal 3 Note (5)
9 VeeR Receiver Ground 1
10 VeeR Receiver Ground 1
11 VeeR Receiver Ground 1
12 RD- Inv. Received Data Out 3 Note (6)
13 RD+ Received Data Out 3 Note (6)
14 VeeR Receiver Ground 1
15 VccR Receiver Power 2 Note (7)
16 VccT Transmitter Power 2 Note (7)
17 VeeT Transmitter Ground 1
18 TD+ Transmit Data In 3 Note (8)
19 TD- Inv. Transmit Data In 3 Note (8)
20 VeeT Transmitter Ground 1
Plug Seq.: Pin engagement sequence during hot plugging.

SPBD-155F4J1R
DELTA ELECTRONICS, INC.
7 Revision: S1
09/20/2006
www.deltaww.com
Notes:
1) Circuit ground is internally isolated from frame (chassis) ground. Tx GND and Rx GND may be internally isolated
within the TRx module.
2) TX Fault is an open collector/drain output, which should be pulled up with a 4.7K~10Kresistor on the host board.
Pull up voltage between 2.0V and VccT+0.3V. The output indicates Low when the transmitter is operating
normally, and High with a laser fault including laser end-of-life. In the low state, the output will be pulled to less
than 0.8V.
3) TX disable is an input that is used to shut down the transmitter optical output. It is pulled up within the module
with a 4.7 – 10 K resistor. Its states are:
Low (0 – 0.8V): Transmitter on
(>0.8, < 2.0V): Undefined
High (2.0 – 3.465V): Transmitter Disabled
Open: Transmitter Disabled
4) Mod-Def 0,1,2. These are the module definition pins. They should be pulled up with a 4.7K – 10Kresistor on the
host board. The pull-up voltage shall be VccT or VccR.
Mod-Def 0 is grounded by the module to indicate that the module is present
Mod-Def 1 is the clock line of two-wire serial interface for serial ID
Mod-Def 2 is the data line of two-wire serial interface for serial ID
5) LOS (Loss of Signal) is an open collector/drain output, which should be pulled up with a 4.7K – 10Kresistor.
Pull up voltage between 2.0V and VccR+0.3V. When high, this output indicates the received optical power is
below the worst-case receiver sensitivity. Low indicates normal operation. In the low state, the output will be
pulled to less than 0.8V.
6) RD-/+: These are the differential receiver outputs. They are AC coupled 100differential lines which should be
terminated with 100(differential) at the user SERDES. The AC coupling is done inside the module and is thus
not required on the host board. The voltage swing on these lines will be between 400 and 2000 mV differential
(200 – 1000 mV single ended) when properly terminated.
7) VccR and VccT are the receiver and transmitter power supplies. They are defined as 3.3V ±5% at the SFP
connector pin. Recommended host board power supply filtering is shown below page. Inductors with DC
resistance of less than 1 Ohm should be used in order to maintain the required voltage at the SFP input pin with
3.3V supply voltage. When the recommended supply-filtering network is used, hot plugging of the SFP
transceiver module will result in an inrush current of no more than 30 mA greater than the steady state value.
8) TD-/+: These are the differential transmitter inputs. They are AC-coupled, differential lines with 100 
differential termination inside the module. The AC coupling is done inside the module and is thus not
required on the host board. The inputs will accept differential swings of 500 – 2400 mV (250 – 1200
mV single-ended), though it is recommended that values between 500 and 1200 mV differential (250 –
600 mV single-ended) be used for best EMI performance.

SPBD-155F4J1R
DELTA ELECTRONICS, INC.
8 Revision: S1
09/20/2006
www.deltaww.com
8. Recommend Interface Circuit
Laser Diode
Photo Diode
1uH
1uH
0.1uF10uF
0.1uF
0.01uF
0.01uF
0.01uF
0.01uF
0.1uF10uF
RES1
RES1
100 Ohms*
RES1 RES1 RES1
10k Ohms
100 Ohms
VCC
Protocol Vcc
SerDes ICProtocol IC
PLD / PAL Mod_def 2
Mod_def 1
Mod_def 0
3.3V
3.3V
DELTA SFP Module
Preamp &
Tx_Disable
Quantizer
Tx_Fault
TD +
TD -
VeeT
RD +
RD -
Rx_LOS
VeeR
Tx_Disable
Tx_Fault
Rx_LOS
RES1 = 4.7k to 10k Ohms
VccT
VccR
Laser Driver
* Depands on SerDes IC used
EEPROM
SFP Host Board Schematic
Recommended Host Board Supply Filtering Network
Design criterion of the capacitor used is the
resonant frequency and its value must be in the
order of the nominal data rate. Short trace
lengths are mandatory.

SPBD-155F4J1R
DELTA ELECTRONICS, INC.
9 Revision: S1
09/20/2006
www.deltaww.com
9. Outline Dimensions
Transmitter Wavelength Latch Color Identifier
1310nm Black
1550nm Yellow
Week (52Weeks/Year) : 1月2日=01
Class 1 Laser Product
1040.10 and 1040.11
Made in x
Complies with 21 CFR
FS
XXXX nm Tx / Rx XXXX nm

SPBD-155F4J1R
DELTA ELECTRONICS, INC.
10 Revision: S1
09/20/2006
www.deltaww.com
10. EEPROM Serial ID Memory Contents (2-Wire Address A0h)
Address Hex ASCII Address Hex ASCII Address Hex ASCII Address Hex ASCII Address Hex ASCII Address Hex ASCII
00 03 25 20 50 4A J 75 SN 100 00 125 00
01 04 26 20 51 31 1 76 SN 101 00 126 00
02 07 27 20 52 52 R 77 SN 102 00 127 00
03 00 28 20 53 20 78 SN 103 00 128 00
04 08 29 20 54 20 79 SN 104 00 ~ 00
05 02 30 20 55 20 80 SN 105 00 255 00
Reserved
for future
use.
06 40 31 20 56 30 81 SN 106 00
07 00 32 20 57 30 82 SN 107 00
08 00 33 20 58 30 83 SN 108 00
09 00 34 20 59 30 84 DC Note 3 109 00
10 00 35 20 60 06 85 DC 110 00
11 03 36 00 61 0E 86 DC 111 00
12 02 37 00 62 00 87 DC 112 00
13 00 38 00 63 CS1 Note 1 88 DC 113 00
14 0F 39 00 64 00 89 DC 114 00
15 96 40 53 S 65 1A 90 DC 115 00
16 00 41 50 P 66 05 91 DC 116 00
17 00 42 42 B 67 05 92 00 117 00
18 00 43 44 D 68 SN Note 2 93 00 118 00
19 00 44 2D - 69 SN 94 00 119 00
20 44 D 45 31 1 70 SN 95 CS2 Note 4 120 00
21 45 E 46 35 5 71 SN 96 00 121 00
22 4C L 47 35 5 72 SN 97 00 122 00
23 54 T 48 46 F 73 SN 98 00 123 00
24 41 A 49 34 4 74 SN 99 00 124 00
Notes:
1) Byte 63(CS1): Check sum of bytes 0-62.
2) Byte 68-83 (SN): Serial number.
3) Byte 84-91 (DC): Date code.
4) Byte 95 (CS2): Check sum of bytes 64-94.
2 wire address
1010000 X (A0h)
0
95
Serial ID Defined
by SFP MSA
(96 bytes)
96
127
Vender Specific
(32 bytes)
128
255
Reserved in SFP
MSA
(128 bytes)

SPBD-155F4J1R
DELTA ELECTRONICS, INC.
11 Revision: S1
09/20/2006
www.deltaww.com
11. Regulatory Compliance
Feature Test Method Reference Performance
Human Body Model
(HBM)
MIL-STD-883E Method 3015.7
EIA-JESD22-A114
Electrostatic Discharge
(ESD) to the Electrical
Pins Machine Model (MM) EIA-JESD22-A115
Contact Discharge IEC/EN 61000-4-2Electrostatic Discharge
(ESD) to the Simplex
Receptacle Air Discharge IEC/EN 61000-4-2
Radio Frequency
Electromagnetic Field
Immunity
IEC/EN 61000-4-3
Electromagnetic
Interference (EMI)
FCC Part 15 Class B
EN 55022 Class B
(CISPR 22A)
(1) Satisfied with
electrical
characteristics of
product spec.
(2) No physical damage
Laser Eye Safety
FDA/CDRH
TUV
FDA 21CFR 1040.10, 1040.11
IEC/EN 60825-1
IEC/EN 60825-2
CDRH File # 0420993
TUV Certificate #
R50032471
Component Recognition
TUV
UL/CSA
IEC/EN 60950
UL 60950
UL File # E239394
Appendix A. Document Revision
Version No. Date Description
S0 2006-03-28 Preliminary datasheet
S1 2006-09-20
1. Update receiver differential data output swing to min. 400mV.
2. Update EEPROM contents of Byte 60,61 to 06,0E
3. Add barcode on product label