Delta Electronics LCP-8500A4EDR User manual

LCP-8500A4EDR
Preliminary
DELTA ELECTRONICS, INC.
1 2008/7/16
Rev. 0A
www.deltaww.com
RoHS Compliant 8.5Gb/s Short Wavelength SFP+ Transceiver
FEATURES
 Compliant with SFP+ MSA, SFF-8431
specification and Fiber Channel FC-PI-4
 Compliant with SFF-8472 MSA
 850nm VCSEL laser
 Built-in digital diagnostic monitoring function
 Backward compatible to 2G/4G Fiber Channel
 Duplex LC connector
 Power consumption ＜1W
 Laser Class 1 Product which comply with the
requirements of IEC 60825-1 and IEC 60825-2
Description
The LCP-8500A4EDR is hot pluggable 3.3V
Small-Form-Factor transceiver modules designed
expressly for high-speed communication
applications that require rates of up to 8.5Gb/s.
It is compliant with SFP+ MSA, SFF-8431
specification and Fiber Channel FC-PI-4, as well as
MSA SFF-8472.
The LCP-8500A4EDR transceivers provide with the
LC receptacle that is compatible with the industry
standard LCTM connector. The transceiver is also
compatible with industry standard RFT connector
and cage.
The post-amplifier of the LCP-8500A4EDR also
includes a LOS (Loss Of Signal) circuit that
provides a TTL logic-high output when an
unusable optical signal level is detected.
The LCP-8500A4EDR transceiver is a Class 1
eye safety product. The optical power levels,
under normal operation, are at eye safe level.
Applications

High-speed storage area networks

Computer cluster cross-connect

Custom high-speed data pipes

LCP-8500A4EDR
Preliminary
DELTA ELECTRONICS, INC.
2 2008/7/16
Rev. 0A
www.deltaww.com
Absolute Maximum Ratings
Parameter Symbol Min. Typ. Max. Unit Note
Storage Temperature TS-40 85 ºC
Supply Voltage VCC 0 4 V
Relative Humidity RH 5 95 %
Recommended Operating Conditions
Parameter Symbol Min. Typ. Max. Unit Note
Case Operating Temperature TC-5 70 ºC
Supply Voltage VCC 3.135 3.465 V
Data Rate 8.5 9 Gbps
Electrical Characteristics
(VCC=3.135V to 3.465V)
Parameter Symbol Min. Typ. Max. Unit Note
Total Supply Current ICC 180 300 MA
Transmitter
Differential Input Voltage Vin,pp 120 1000 mVppd 1
Data Input Rise/Fall Time 15 40 Ps 2
Transmitter Disable Input-High VDISH 2 VCC+0.3 V
Transmitter Disable Input-Low VDISL 0 0.8 V
Transmitter Fault Output-High VTXFH 2 VCC+0.3 V
Transmitter Fault Output-Low VTXFL 0 0.8 V
Receiver
Differential Output Voltage Vout,pp 300 1000 mVppd 3
Data Output Rise/Fall Time 45 Ps 1
LOS Output Voltage-Low VLOSH 2 VCC+0.3 V
LOS Output Voltage-High VLOSL 0 0.8 V
VIL -0.3 0.8 V 4
RS0, RS1 VIH 2.0 Vcc+0.3 V
Notes:
1. Internally AC coupled and terminated to 100 Ohm differential load.
2. These are 20%~80% values.
3. Internally AC coupled, but requires a 100 Ohm differential termination at or internal to Serializer/ Deserializer.
4. Shall be pulled low to VeeT with a ＞30k ohms resistor in the module.

LCP-8500A4EDR
Preliminary
DELTA ELECTRONICS, INC.
3 2008/7/16
Rev. 0A
www.deltaww.com
Optical Characteristics
(VCC=3.135V to 3.465V, Data Rate=8.5Gb/sec, PRBS=27-1 NRZ, 50/125µm MMF)
Parameter Symbol Min. Typ. Max. Unit Note
Transmitter
Output Optical Power (Avg.) PO-8.2 -1.8 dBm
Optical Modulation Amplitude OMA 302
µW 1
Center Wavelength λ840 850 860 nm
Spectral Width (RMS) σ0.65 nm
Optical Rise/Fall Time (20% - 80%) tr/ tf50/50 ps 2
RIN12OMA -128 dB/Hz 3
Output Eye Complies with the ANSI FC-PI-4 Rev. 6.01 specification, and is class
1 laser eye safety
Receiver
Sensitivity in OMA
@8.5Gbps
@4.25Gbps
@2.125Gbps
PIN
76
61
49
µW 4
Input Optical Wavelength λ840 850 860 nm
Average Received Power, max Rmax 0 dBm
LOS-De-asserted (Avg.) PD-14 dBm
LOS-Asserted (Avg.) PA-30 dBm
LOS-Hysteresis PD-PA0.5 dB
Optical Return Loss ORL 12 dB
Link Length
Data Rate/Standard Fiber Type Modal Bandwidth
@850nm (MHz*km) Distance Range(m) Notes
.
62.5/125 µm MMF 200 0.5 to 21 5
50/125 µm MMF 500 0.5 to 50 5
50/125 µm MMF 900 0.5 to 90 5
50/125 µm MMF 1500 0.5 to 120 5
8.5Gbps
50/125 µm MMF 2000 0.5 to 150 5
Notes:
1. Equivalent extinction ratio specification for Fiber Channel. Allows smaller ER at higher average power.
2. Measured at nominal data rate. These are unfiltered 20%~80% values.
3. Transmitter Dispersion Penalty is measured using the methods specified in the IEEE standard 802.3-2005 Clause
52 except that the transversal filter differential delay is 33 ps.
4. The sensitivity is tested at a BER of 1×10-12 or better with an input signal consisting of 27-1 NRZ PRBS.
5. Distance, shown in the “Link Length” table, are calculated for worst case fiber and transceiver characteristics
based on the optical and electrical specifications shown in this document using techniques utilized in IEEE 802.3.
In the nominal case, longer distances are achievable.

LCP-8500A4EDR
Preliminary
DELTA ELECTRONICS, INC.
4 2008/7/16
Rev. 0A
www.deltaww.com
SFP+ Transceiver Electrical Pad Layout
Module Electrical Pin Definition

LCP-8500A4EDR
Preliminary
DELTA ELECTRONICS, INC.
5 2008/7/16
Rev. 0A
www.deltaww.com
Pin Logic Symbol Name/Description Note
1 VeeT Module Transmitter Ground 1
2 LVTTL-O TX_Fault Module Transmitter Fault 2
3 LVTTL-I TX_Disable Transmitter Disable; Turns off transmitter laser output 3
4 LVTTL-I/O SDA 2- write Serial Interface Data Line
5 LVTTL-I/O SCL 2- write Serial Interface Clock
6 MOD_ABS Module Absent, connected to VeeT or VeeR in the module 4
7 LVTTL-I RS0
Rate Select 0, optionally controls SFP+ module receiver.
When High input data rate>4.25GBd and when LOW input
data rate 4.25GBd.≦
8 LVTTL-O RX_LOS Receiver Loss of Signal Indication 2
9 LVTTL-I RS1 Not Implement
10 VeeR Module Receiver Ground 1
11 VeeR Module Receiver Ground 1
12 CML-O RD- Receiver Inverted Data Output
13 CML-O RD+ Receiver Non-Inverter Data Output
14 VeeR Module Receiver Ground 1
15 VccR Module Receiver 3.3V Supply
16 VccT Module Transmitter 3.3V Supply
17 VeeT Module Transmitter Ground 1
18 CML-I TD+ Transmitter Non-Inverted Data Input
19 CML-I TD- Transmitter Inverted Data Input
20 VeeT Module Transmitter Ground 1
Notes:
1. The module signal ground pins, VeeR and VeeT, shall be isolated from the module case.
2. This pin is an open collector/drain output pin and shall be pulled up with 4.7k-10k ohms to Host_Vcc
on the host board. Pull ups can be connected to multiple power supplies, however the host board
design shall ensure that no module pin has voltage exceeding module VccT/R + 0.5V.
3. This pin is an open collector/drain input pin and shall be pulled up with 4.7k-10k ohms to VccT in the
Module.
4. This pin shall be pulled up with 4.7k-10k ohms to Host_Vcc on the host board.

LCP-8500A4EDR
Preliminary
DELTA ELECTRONICS, INC.
6 2008/7/16
Rev. 0A
www.deltaww.com
Low speed electrical control pins and 2-wire interface
In addition to the 2-wire serial interface, the SFP+ module has the following low speed pins for control and
status:
‧TX_Fault
‧TX_Disable
‧RS0/RS1
‧MOD_ABS
‧RX_LOS
1. TX_Fault
.TX_Fault is a module output pin that when High, indicates that the module transmitter has detected a fault
condition related to laser operation or safety.
The TX_Fault output pin is an open drain/collector and must be pulled p to the Host_Vcc with 4.7k-10k
ohms on the host board.
2. TX_Disable
TX_Disable is a module input pin. When TX_Disable is asserted High or Left open, the SFP+ module
transmitter output must be turned off. The TX_DIS pin must be pulled up to VccT in the SFP+ module.
3. RS0/RS1
RS0 and RS1 are module input rate select pins and are pulled low to VeeT with a > 30kΩresistor in the
module. RS0 is an input hardware pin which optionally selects the optical receives data path rate
coverage for an SFP+ module. RS1 is an input hardware pin which optionally selects the optical transmits
path data rate coverage for an SFP+ module.
RS1 is commonly connected to VeeT or VeeR in the legacy SFP modules. The host needs to ensure that
it will not be damaged if this pin is connected to VeeT or VeeR in the module.
4. MOD_ABS
Mod_ABS is pulled up to Host_Vcc with 4.7k-10k ohms on the host board and connected to VeeT or VeeR
in the SFP+ module. MOD_ABS is then asserted “High” when the SFP+ module is physically absent from
a host slot. In the SFP MSA (INF8074i) this pin had the same function but is called MOD_DEF0.
5. SCL/SDA
SCL is the 2-wire interface clock and SDA is the 2-wire interface data line. SCL and SDA are pulled up to
a voltage in the range of 3.14V to 3.46V on the host.
6. RX_LOS
RX_LOS when High Indicated an optical signal level below that specified in the relevant standard. The
RX_LOS pin is an open drain/collector outpit and must be pulled up to host Vcc with a 4.7k-10k ohms on
the host board.
RX_LOS assert min and de-assert max are defined in the relevant standard. To avoid spurious transition
of RX_LOS a minimum hysteresis of 0.5 dBo is recommended.

LCP-8500A4EDR
Preliminary
DELTA ELECTRONICS, INC.
7 2008/7/16
Rev. 0A
www.deltaww.com
Laser Diode
Photo Diode
Laser Driver
100 Ohms
0.01uF
0.01uF
0.01uF
0.01uF
Preamp &
Qu an t i ze r
EEPROM
10K Ohms
DELTA SFP+ Module
0.1uF
0.1uF10uF
1uH
1uH
0.1uF10uF
3.3V
100 Ohms*
RES1
RES1
VCC
SerDes IC
RES1RES1RES1
3.3V
PLD / PAL
Protocol Vcc
Tx_Dis able
Tx_Fault
Rx_LOS
Receiv er Rate Select
Transmit t er Rat e Select
Protocol IC
VccT
Tx_Disable
Tx_Fault
TD+
TD-
VeeT
VccR
RD+
RD-
Rx_LOS
VeeR
RS0
RS1
SCL
SDA
MOD- ABS
RES1 = 4.7k TO 10k Ohms
* Depands on SerDes IC used
30k Ohms
30k Ohms Mi c ro
Cont rol
Recommend Circuit Schematic

LCP-8500A4EDR
Preliminary
DELTA ELECTRONICS, INC.
8 2008/7/16
Rev. 0A
www.deltaww.com
Package Outline Drawing for Metal Housing with Bail de-latch
Complies with 21 CFR
1040.10 and 1040.11
Made in x FSFS

LCP-8500A4EDR
Preliminary
DELTA ELECTRONICS, INC.
9 2008/7/16
Rev. 0A
www.deltaww.com
Timing parameters for SFP+ management
Parameter Symbol Min. Max. Unit Note
TX_DISABLE Assert time t_off 10 µsec 1
TX_DISABLE Negate time t_on 2 msec 2
Time to initialize 2-wire
interfase t_2w_start_up 300 msec 3
Time to initialize t_start_up 300 msec 4
Time to initialize cooled
module t_start_up_cooled 90 sec 4
Time to Power Up to Level 2 t_power_level2 300 msec 5
Time to Power Down from
Level 2 T_power_down 300 msec 6
TX_Fault assert TX_Fault_on 1 msec 7
TX_Fault assert for cooled
module TX_Fault_on 50 msec 7
TX_Fault Reset t_reset 10 µsec 8
Module Reset t_module_reset TBD msec TBD
RS0, RS1 rate select timing
for FC
t_RS0_FC,
RS1_FC 500 µsec 9
RS0, RS1 rate select timing
non FC t_RS0, t_RS1 10 msec 9
RX_LOS assert delay t_los_on 100 µsec 10
RX_LOS negate delay t_los_off 100 µsec 11
Notes:
1) Rising edge of TX_Disable to fall of output signal below 10% of nominal.
2) Falling edge of TX_Disable to rise of output signal above 90% of nominal. This only applies in normal operation,
not during start up or fault recovery.
3) From power on or negation of TX_Disable.
4) From power on or TX_Disable negated during power up, or TX_Fault recovery, until non-cooled power level 1
part (or non-cooled power level 2 part already enabled at power level 2 for TX_Fault recovery) is fully operational.
5) From falling edge of stop bit enabling power level 2 until non-cooled module is fully operational.
6) From falling edge of stop bit disabling power level 2 until module is within power level 1 requirements.
7) From Occurrence of fault to assertion of TX_Fault.
8) Time TX_Disable must be held High to reset TX_Fault.
9) From assertion till stable output.
10) From Occurrence of loss of signal to assertion of LOS.
11) From Occurrence of presence of signal to negation of RX_LOS.

LCP-8500A4EDR
Preliminary
DELTA ELECTRONICS, INC.
10 2008/7/16
Rev. 0A
www.deltaww.com
Enhanced Digital Diagnostic Interface
The memory map in the following describes an extension to the memory map defined in SFP+ MSA. The enhanced
interface uses the two wire serial bus address 1010001x (A2h) to provide diagnostic information about the module’s
present operating conditions.
2 wire address 1010000 X (A0h) 2 wire address 1010001 X (A2h)
0 0
55
Alarm and Warning Thresholds
(56 bytes)
95
Serial ID Defined by SFP MSA
(96 bytes) 56
95
Cal Constants
(40 bytes)
96 96
119
Real Time Diagnostic Interface
(24 bytes)
127
Vender Specific
(32 bytes) 120
127
Vender Specific(Note)
128 128
247
User Writable EEPROM
(120 bytes)
255
Reserved in SFP MSA
(128 bytes) 248
255
Vender Specific
(8 bytes)
Digital Diagnostic Memory Map Specific Data Field Descriptions
Note:
1) Write the password (11h, 11h, 11h, 11h) on the bytes of 123-126 of address A2h then the address of
bytes 128-255 (User Writable) can be read and written.

LCP-8500A4EDR
Preliminary
DELTA ELECTRONICS, INC.
11 2008/7/16
Rev. 0A
www.deltaww.com
EEPROM Serial ID Memory Contents (2-Wire Address A0h)
Address Hex ASCII Address Hex ASCII Address Hex ASCII
00 03 43 2D - 86 DC
01 04 44 38 8 87 DC
02 07 45 35 5 88 DC
03 03 46 30 0 89 DC
04 00 47 30 0 90 DC
05 00 48 41 A 91 DC
06 00 49 34 4 92 68
07 40 50 45 E 93 FA
08 40 51 44 D 94 03
09 0C 52 52 R 95 CS2 Note 4
10 54 53 30 96 00
11 03 54 30 97 00
12 55 55 30 98 00
13 03 56 41 99 00
14 00 57 20 100 00
15 00 58 20 101 00
16 05 59 20 102 00
17 02 60 03 103 00
18 00 61 52 104 00
19 00 62 00 105 00
20 44 D 63 CS1 Note 1 106 00
21 45 E 64 00 107 00
22 4C L 65 3A 108 00
23 54 T 66 00 109 00
24 41 A 67 00 110 00
25 20 68 SN Note 2 111 00
26 20 69 SN 112 00
27 20 70 SN 113 00
28 20 71 SN 114 00
29 20 72 SN 115 00
30 20 73 SN 116 00
31 20 74 SN 117 00
32 20 75 SN 118 00
33 20 76 SN 119 00
34 20 77 SN 120 00
35 20 78 SN 121 00
36 00 79 SN 122 00
37 00 80 SN 123 00
38 00 81 SN 124 00
39 00 82 SN 125 00
40 4C L 83 SN 126 00
41 43 C 84 DC Note 3 127 00
42 50 P 85 DC 128 00 Note5
Notes:
1) Byte 63: Check sum of bytes 0-62.
2) Byte 68-83: Serial number.
3) Byte 84-91: Date code.
4) Byte 95: Check sum of bytes 64-94.
5) Byte 128 to 255 had been set hex 00.

LCP-8500A4EDR
Preliminary
DELTA ELECTRONICS, INC.
12 2008/7/16
Rev. 0A
www.deltaww.com
Digital Diagnostic Monitoring Interface
Alarm and Warning Thresholds (2-Wire Address A2h)
Address #
Bytes Name Value (Dec.) Unit Note
00-01 2 Temp High Alarm TC (MAX.)+15
02-03 2 Temp Low Alarm TC (MIN.)
04-05 2 Temp High Warning TC (MAX.)+10
06-07 2 Temp Low Warning TC (MIN.)+10
℃1
08-09 2 Voltage High Alarm Vcc+5%
10-11 2 Voltage Low Alarm Vcc-5%
12-13 2 Voltage High Warning Vcc+3%
14-15 2 Voltage Low Warning Vcc-3%
Volt
16-17 2 Bias High Alarm IOP+10
18-19 2 Bias Low Alarm IOP-5
20-21 2 Bias High Warning IOP+7
22-23 2 Bias Low Warning IOP-3
mA 2
24-25 2 TX Power High Alarm P+3
26-27 2 TX Power Low Alarm P-3
28-29 2 TX Power High Warning P+2
30-31 2 TX Power Low Warning P-2
dBm 3
32-33 2 RX Power High Alarm P0+3
34-35 2 RX Power Low Alarm PS-2
36-37 2 RX Power High Warning P0+2
38-39 2 RX Power Low Warning PS
dBm 4
40-45 16 Reversed
56-91 36 External Calibration Constants
92-94 3 Reversed
95 1 Checksum 5
96-97 2 Real Time Temperature
98-99 2 Real Time Supply Voltage
100-101 2 Real Time Tx Bias Current
102-103 2 Real Time Tx Optical Power
104-105 2 Real Time Rx Received Power
106-109 4 Reserved
110 1 Optional Status/ Control Bits 6
111 1 Reserved
112-119 8 Optional Set of Alarm and Warning 7
Notes:
1) TC: Case operating temperature.
2) IOP: Operating current at room temperature. The min. setting current is 0 mA.
3) P: Operating optical power of transmitter at room temperature.
4) P0: Overload optical power of receiver.
PS: Sensitivity optical power of receiver.
5) Byte 95 contains the low order 8bits of sum of bytes 0-94.

LCP-8500A4EDR
Preliminary
DELTA ELECTRONICS, INC.
13 2008/7/16
Rev. 0A
www.deltaww.com
6)
State/ Control Bits
Byte Bit Name Description
110 7 Tx Disable State Digital state of the Tx disable input pin
110 6 Soft Tx Disable Read/ Write bit that allow software disable of laser
110 5 Reserved
110 4 Rate Select tate NA
110 3 Soft Rate Select NA
110 2 Tx Fault Digital state of the Tx fault output pin
110 1 LOS Digital state of the LOS output pin.
110 0 Data_Ready_Bar NA
7)
Optional Set of Alarm and Warning
Byte Bit Name Description
112 7 Temp High Alarm Set when internal temperature exceeds high alarm level
112 6 Temp Low Alarm Set when internal temperature is below low alarm level
112 5 Vcc High Alarm Set when internal supply voltage exceeds high alarm level
112 4 Vcc Low Alarm Set when internal supply voltage is below low alarm level
112 3 Tx Bias High Alarm Set when Tx Bias current exceeds high alarm level
112 2 Tx Bias Low Alarm Set when Tx Bias current is below low alarm level
112 1 Tx Power High Alarm Set when Tx output power exceeds high alarm level
112 0 Tx Power Low Alarm Set when Tx output power is below low alarm level
113 7 Rx Power High Alarm Set when received power exceeds high alarm level
113 6 Rx Power Low Alarm Set when received power is below low alarm level
113 5-0 Reserved
116 7 Temp High Warning Set when internal temperature exceeds high warning level
116 6 Temp Low Warning Set when internal temperature is below low warning level
116 5 Vcc High Warning Set when internal supply voltage exceeds high warning level
116 4 Vcc Low Warning Set when internal supply voltage is below low warning level
116 3 Tx Bias High Warning Set when Tx Bias current exceeds high warning level
116 2 Tx Bias Low Warning Set when Tx Bias current is below low warning level
116 1 Tx Power High Warning Set when Tx output power exceeds high warning level
116 0 Tx Power Low Warning Set when Tx output power is below low warning level
117 7 Rx Power High Warning Set when received power exceeds high warning level
117 6 Rx Power Low Warning Set when received power is below low warning level
117 5-0 Reserved
Digital Diagnostic Monitor Accuracy
Parameter Typical Value Note
Transceiver Temperature ±3℃1
Power Supply Voltage ±3% 2
TX Bias Current ±10%
TX Optical Power ±1.5dB
RX Optical Power ±3dB
Notes:
1) Temperature is measured internal to the transceiver.
2) Voltage is measured internal to the transceiver.

LCP-8500A4EDR
Preliminary
DELTA ELECTRONICS, INC.
14 2008/7/16
Rev. 0A
www.deltaww.com
Regulatory Compliance
Test Item Reference Qty’ Evaluation
(#1)
Electromagnetic Interference
EMC
FCC Class B
EN 55022 Class B
CISPR 22
5
(#2) Immunity：
Radio Frequency
Electromagnetic Field
EN 61000-4-3
IEC 1000-4-3
5
(#3) Immunity：
Electrostatic Discharge to the
Duplex SC Receptacle
EN 61000-4-2
IEC 1000-4-2
IEC 801.2
5
(#4) Electrostatic Discharge to
the Electrical Pins
MIL-STD-883C
Method 3015.4
EIAJ#1988.3.2B
Version 2,
Machine model
5
(1) Satisfied with electrical characteristics of
product spec.
(2) No physical damage