Delta Electronics SFBD-155E2J1RM User manual

SFBD-155E2J1RM
DELTA ELECTRONICS, INC.
1 Revision: S0
12/20/2006
www.deltaww.com
Small Form Factor Bi-Directional Transceiver Module
for Fast Ethernet, ATM, SONET OC-3/SDH STM-1
FEATURES
 RoHS compliant
 2x5 Pin SFF Package with SC Receptacle
 Single Mode Fiber, Bi-Directional
Transmission with 1310nm Transmitter and
1550nm Receiver
 Link Distance up to 15km
 Single +3.3V power supply and PECL logic
interface
 Wave Solderable and Aqueous Washable
 Bellcore GR-468 compliant
 Laser Class 1 Product which comply with the
requirements of IEC 60825-1 and IEC 60825-2
Description
DELTA’s SFF Bi-Directional transceiver is
designed for point-to-point Bi-Directional Optical
Network transmission. The module consists
multiple quantum well laser, InGaAs PIN,
Preamplifier and WDM filter in a high-integrated
optical sub-assembly, and it receives up to
155Mbps of continuous data at 1550nm, and
transmits 155Mbps of continuous data at 1310nm.
The module is contained in a 2x5 SFF
industry standard package with a SC receptacle
connector, and support LVTTL transmitter disable
input, LVPECL electrical signal Interface and
receiver signal detect output.
Application
 TTC TS-1000
 ITU-T G.985
 IEEE 802.3ah 100BASE-BX/ Fast Ethernet
 SONET OC-3/SDH STM-1/ ATM Network
 FTTx Broadband Access System
Performance
 SFBD-155E2J1RM data link up to 15km in
9/125um single mode fiber.

SFBD-155E2J1RM
DELTA ELECTRONICS, INC.
2 Revision: S0
12/20/2006
www.deltaww.com
0.85
1.20
0.80
1.00
0.50
0.20
0.00
-0.20
Amplitude
0.350.150.00
Time
0.65
Mean level of logical "0"
1.00
Mean level of logical "1"
Optical Pulse Mask with Bessel Filter Specified in ITU
-
T G.957
1. Absolute Maximum Ratings
Parameter Symbol Min. Typ. Max. Unit Note
Storage Temperature Ts -40 85 ºC
Storage Ambient Humidity HA5 95 %
Power Supply Voltage VCC -0.5 5 V
Signal Input Voltage -0.3 Vcc+0.3 V
Optical Input Power (Peak) 0 dBm
Lead Soldering Temperature TSOLD 260 ºC
Lead Soldering Time tSOLD 10 sec
2. Recommended Operating Conditions
Parameter Symbol Min. Typ. Max. Unit Note
Ambient Operating Temperature TA0 70 ºC
Without air flow
Ambient Humidity HA5 85 %
Non-condensing
Power Supply Voltage VCC 3.13 3.3 3.47 V
Power Supply Current ICC 230 mA
Power Supply Noise Rejection 100 mVp-p 100Hz to 1MHz
Data Rate 10 155.52 Mbps
Transmission Distance 15 km
3. Optical Specification of Transmitter
Parameter Symbol Min. Typ. Max. Unit Note
Average Launched Power PO-14 -11 -8 dBm Note (1)
Launched power (Peak.) -5 dBm
Extinction Ratio ER 8.5 dB
Center Wavelength λC1260 1310 1360 nm
Spectrum Width (RMS) σ6 nm
Optical Rise/Fall Time tr/tf1.3 ns Note (2)
Total Jitter tJ1 ns Note (3)
Optical Transmitter Reflectance -14 dB
Optical Return Loss Tolerance ORLT 14 dB
Relative Intensity Noise RIN -116 dB/Hz
Output Eye Mask Compliant with Bellcore TR-NWT-000253
and ITU recommendation G.957 Note (4)
Note (1). Launched power (avg.) is power coupled into a 9/125um single mode fiber.
Note (2). These are unfiltered 20-80% values.
Note (3). Measure at 223-1 NRZ PRBS pattern.
Note (4). Eye Mask definition

SFBD-155E2J1RM
DELTA ELECTRONICS, INC.
3 Revision: S0
12/20/2006
www.deltaww.com
4. Optical Specification of Receiver
Parameter Symbol Min. Typ. Max. Unit Note
Input Optical Wavelength λIN 1480 1600 nm
Receiver Sensitivity PIN -30 dBm Note (1)
Input Saturation Power (Overload) PSAT -3 dBm
Signal Detect -Assert Power PA- -30 dBm
Signal Detect -Deassert Power PD-44 dBm Note (2)
Signal Detect Hysteresis PA-PD0.5 2.5 6 dB
Optical Receiver Reflectance -14 dB Note (3)
Output Data Rise/Fall time tr/tf1.5 ns Note (4)
S/X Endurance 10 dB Note (5)
Optical Isolation 25 dB Note (6)
Note (1). Measured with 1520nm, ER=10dB; BER =<10-10@PRBS=223-1 NRZ
Note (2). When SD deasserted, the data output is Low-level (fixed)
Note (3). When the terminal is viewed from the optical path, the reflection toward the optical path of the
optical signal with a central wavelength of 1480nm to 1580nm transmitted to terminal.
Note (4). These are 20%~80% values
Note (5). X=10 MHz, Rectangular BER =10-10
Note (6). Receiver isolation between 1260nm ~1360nm
5. Electrical Interface Characteristics
Parameter Symbol Min. Typ. Max. Unit Note
Transmitter
Total Supply Current ICC A mA Note (1)
Differential line input Impedance RIN 80 100 120 Ohm
Differential Data Input Swing VDT 300 1600 mVp-p
Data Input Voltage- High VIH-VCC -1.165 -0.880 V
Data Input Voltage- Low VIL-VCC -1.810 -1.475 V LVPECL
Transmitter Disable Input-High VDISH 2 VCC+0.3 V
Transmitter Disable Input-Low VDISL 0 0.8 V LVTTL
Receiver
Total Supply Current ICC B mA Note (1)
Differential Data Output Swing VDR 400 2000 mVp-p
Data Output Voltage-High VOH-VCC -1.085 -0.880 V
Data Output Voltage-Low VOL-VCC -1.830 -1.555 V
Signal Detect Output Voltage-High VOH-VCC -1.085 -0.880 V
Signal Detect Output Voltage-Low VOL-VCC -1.830 -1.555 V
LVPECL
Note (1). A (TX)+ B (RX) = 230mA
(A: Not include termination circuit; B: using a resister of 150Ωbetween Data-output and ground)

SFBD-155E2J1RM
DELTA ELECTRONICS, INC.
4 Revision: S0
12/20/2006
www.deltaww.com
6. Pin Description
Tx/Rx Pin No. I/O Pin Name Description
1 VeeR Receiver Ground
2 VccR +3.3V Receiver Power Supply
3 O SD
Normal Optical Input indicated by logic “High”, and No Optical
Input indicated by logic “Low”.
4 O RD(n) Inverted Receiver Data Output
Rx
5 O RD(p) Non-Inverted Receiver Data Output
6 VccT +3.3V Transmitter Power Supply
7 VeeT Transmitter Ground
8 I Tx_Dis
LVTTL Logic “High” to Disable Transmitter, and Enable
Transmitter by Logic “Low” or “Open”.
9 I TD(p) Non-Inverted Transmitter Data Input
Tx
10 I TD(n) Inverted Transmitter Data Input
MS Mounting studs/ connect this pin to Chassis ground
Note. EMI shielding lead must be connected to Signal ground
Bottom View
MS
MS

SFBD-155E2J1RM
DELTA ELECTRONICS, INC.
5 Revision: S0
12/20/2006
www.deltaww.com
7. Recommended Interface Circuit
Transmitter
9. TD(p)
10. TD(n)
8. Tx_Dis
6. VccT
7. VeeT
Receiver
1. VeeR
5. RD(p)
4. RD(n)
3. SD
2. VccR
100nF
10uF 100nF
10uF 100nF
1uH
1uH
3.3V
Protocol IC
SerDes IC
Tx_Enable
SD
DELTA SFF Module
270 ohm
Tx-Coupled
interface
Rx-Coupled
interface
82ohm
130ohm
3.3V
130ohm
3.3V
82ohm
100nF
100nF
DELTA
Module
Host
Board
DELTA
Module
Host
Board
Z0=50ohm
Z0=50ohm
RES0RES0
Z0=50ohm
Z0=50ohm
DC - Coupled interface AC - Coupled interface
Tx-Coupled
interface
3.3V
130ohm
82ohm
130ohm
82ohm
3.3V
82ohm
130ohm
3.3V
130ohm
3.3V
82ohm 100nF
100nF
DELTA
Module
Host
Board
DELTA
Module
Host
Board
Z0=50ohm
Z0=50ohm
Z0=50ohm
Z0=50ohm
DC - Coupled interface AC - Coupled interface
Rx-Coupled
interface
3.3V
RES2
RES1
RES2
RES1
3.3V
150ohm150ohm
RES0, RES1 and RES2 depend on SerDes chip used

SFBD-155E2J1RM
DELTA ELECTRONICS, INC.
6 Revision: S0
12/20/2006
www.deltaww.com
C o m p l i e s w i t h F D A r a d i a t i o n
p e r f o r m a n c e s t a n d a r d s , 2 1 C F R S u b c h a p t e r J .
C l a s s 1 L a s e r P r o d u c t
8. Outline Dimensions
Parameter Unit Description Note
Mechanical Dimensions mm 48.3x13.5x9.6
Connector Type - SC connector IEC-61754-4
Week (52Weeks/Year) : 1月2日=01

SFBD-155E2J1RM
DELTA ELECTRONICS, INC.
7 Revision: S0
12/20/2006
www.deltaww.com
9. Regulatory Compliance
Feature Test Method Reference Performance
Human Body Model
(HBM)
MIL-STD-883E Method 3015.7
EIA-JESD22-A114
Electrostatic Discharge
(ESD) to the Electrical
Pins Machine Model (MM) EIA-JESD22-A115
Contact Discharge IEC/EN 61000-4-2Electrostatic Discharge
(ESD) to the Simplex
Receptacle Air Discharge IEC/EN 61000-4-2
Radio Frequency
Electromagnetic Field
Immunity
IEC/EN 61000-4-3
Electromagnetic
Interference (EMI)
FCC Part 15 Class B
EN 55022 Class B
(CISPR 22A)
(1) Satisfied with
electrical
characteristics of
product spec.
(2) No physical damage
Laser Eye Safety
FDA/CDRH
TUV
FDA 21CFR 1040.10, 1040.11
IEC/EN 60825-1
IEC/EN 60825-2
CDRH File # 0420993
TUV Certificate #
R50032471
Component Recognition
TUV
UL/CSA
IEC/EN 60950
UL 60950
UL File # E239394
Appendix A. Document Revision
Version No. Date Description
S0 2006-12-20 Preliminary Datasheet