Delta Electronics OPT-1250xxxx Series User manual

OPT-1250xxxx Series
DELTA ELECTRONICS, INC.
1 Jan., 2008
Rev. 0H
www.deltaww.com
RoHS Compliant 1X9 SC Duplex Receptacle Transceiver Module for
Gigabit Ethernet
Features
 Industry Standard 1 x 9 Footprint and duplex SC
Connector interface
 Compliant with Specifications for IEEE 802.3z/
Gigabit Ethernet
 OPT-1250Bxxx compliant with the 1.0625GBd
Fiber Channel 100-SM-LC-L FC-PI Rev.13
 OPT-1250Axxx compliant with the 1.0625GBd
Fiber Channel FC-PI 100-M5-SN-I Rev.13

Single +3.3V or 5V Power Supply
 PECL or TTL Receiver Signal Detect Indicator
 Wave Solderable and Aqueous Washable

Laser Class 1 Product which comply with the
requirements of IEC 60825-1 and IEC 60825-2
 RoHS Compliant per Directive 2002/95/EC.
Description
The OPT-1250xxxx series from DELTA is a 1X9
transceiver module designed expressly for
high-speed communication applications that
require rates of up to 1.25Gbit/sec. It is compliant
with the Gigabit Ethernet standards as well as 1x
Fiber channel standards.
The OPT-1250xxxx transceivers are provided with
the SC receptacle that is compatible with the
industry standard SC connector.
The post-amplifier of the OPT-1250xxxx also
includes a Signal Detect circuit that provides a
PECL or TTL logic-Low output when an unusable
optical signal level is detected. (see order
information)
The OPT-1250xxxx transceiver is a Class 1 eye
safety product. The optical power levels, under
normal operation, are at eye safe level.
Applications
 Gigabit Ethernet/Fast Ethernet

Switched backplane applications
Performance
OPT-1250AxFxx:
 850nm VCSEL, up to 500m in 50/125μm MMF
 850nm VCSEL, up to 220m in 62.5/125μm
MMF
OPT-1250BxQxx:
 1310nm FP laser, Data Link up to 10km in
9/125um SMF
 1310nm FP laser, up to 550m in 50/125μm
MMF
 1310nm FP laser, up to 550m in 62.5/125μm
MMF

OPT-1250xxxx Series
DELTA ELECTRONICS, INC.
2 Jan., 2008
Rev. 0H
www.deltaww.com
Absolute Maximum Ratings
Parameter Symbol Min. Typ. Max. Unit Note
Storage Temperature Ts -40 85 ºC
Lead Soldering Temperature TSOLD 260 ºC
Lead Soldering Time tSOLD 10 sec.
Supply Voltage VCC 0 6 V
Recommended Operating Conditions
Parameter Symbol Min. Typ. Max. Unit Note
Ambient Operating Temperature TA0 70 ºC 1
Supply Voltage
OPT-1250x1xx
OPT-1250x2xx, OPT-1250x4xx VCC
4.75
3.135 5.25 3.465 V
Note:
1.See ordering information for detail
Electrical Characteristics
(At recommended ambient operating temperature, TAand supply voltage, VCC)
Parameter Symbol Min. Typ. Max. Unit Note
Total Supply Current ICCT 310 mA
Transmitter
Transmitter Data Input Voltage-Low VIL-VCC -1.810 -1.475 V 1
Transmitter Data Input Voltage-High VIH-VCC -1.165 -0.880 V 1
Transmitter Differential Input Voltage VDT 0.3 1.6 V 2
Receiver
Data Output Voltage-Low VOL-VCC -1.95 -1.62 V 1
Data Output Voltage-High VOH-VCC -1.045 -0.74 V 1
Receiver Differential Output Voltage VDR 0.5 0.7 1.2 V 2
Output Data Rise/Fall Time tr/tf0.4 ns 3
PECL SD Output
LOW level output voltage
HIGH level output voltage
VSDL-VCC
VSDH-VCC
-1.84
-1.1
-1.60
-0.9 V 4
TTL SD Output
LOW level output voltage
HIGH level output voltage
VSDL
VSDH
0
2
0.8
VCC V 5
Notes:
1. For OPT-1250A1F1x, OPT-1250A4F1x, OPT-1250B2Q1x and OPT-1250B1Q1x.
2. For OPT-1250A2F2x and OPT-1250B4Q2x.
3. These are 20%~80% values
4. For OPT-1250A1F1x, OPT-1250A2F2x, OPT-1250B1Q1x and OPT-1250B2Q1x
5. For OPT-1250A4F1x and OPT-1250B4Q2x

OPT-1250xxxx Series
DELTA ELECTRONICS, INC.
3 Jan., 2008
Rev. 0H
www.deltaww.com
Single Mode Transceiver (OPT-1250B1Q1x, OPT-1250B2Q1x, OPT-1250B4Q2x)
(At recommended ambient operating temperature, TAand supply voltage, VCC; Data Rate=1.25Gb/sec,
PRBS=27-1 NRZ, 9/125um SMF)
Parameter Symbol Min. Typ. Max. Unit Note
Transmitter
Output Optical Power (Avg.)
OPT-1250BxIx
OPT-1250BxQx PO
-12
-9.5
-3
-3 dBm
Optical Extinction Ratio ER 9 dB
Center Wavelength λC 1270 1310 1355 nm
Spectral Width (RMS) σ4.5 nm
Optical Rise/Fall time tr/tf0.4 ns 1
Relative Intensity Noise RIN -120 dB/Hz
Output Eye Complies with the IEEE 802.3z/D2 specification, and is class 1
laser eye safety
Receiver
Sensitivity (Avg.) PIN -19 dBm 2
Input Optical Wavelength λ1310 nm
Optical Rise/Fall Time tr/tf0.5 ns 1
Signal Detect-Asserted (Avg.) PA-19 dBm
Signal Detect-De-asserted (Avg.) PD-35 dBm
Signal Detect-Hysteresis PA-PD0.5 dB
Receiver Saturation Power PSAT -3 dBm
Notes:
1. These are unfiltered 20%~80% values
2. The sensitivity is provided at a BER of 1×10-10 or better with an input signal consisting of
1250Mb/s, 27-1 PRBS and ER=9dB.
Mask of the eye diagram for the optical transmit signal

OPT-1250xxxx Series
DELTA ELECTRONICS, INC.
4 Jan., 2008
Rev. 0H
www.deltaww.com
Multi-Mode Series Transceiver (OPT-1250A1F1x, OPT-1250A2F2x, OPT-1250A4F1x)
(At recommended ambient operating temperature, TAand supply voltage, VCC; Data Rate=1.25Gb/sec,
PRBS=27-1 NRZ, 62.5/125um MMF)
Parameter Symbol Min. Typ. Max. Unit Note
Transmitter
Output Optical Power (Avg.) PO-9.5 -4 dBm
Optical Extinction Ratio ER 9 dB
Center Wavelength λC 830 850 860 nm
Spectral Width (RMS) σ0.85 nm
Optical Rise/Fall time tr/tf0.26 ns 1
Relative Intensity Noise RIN -117 dB/Hz
Output Eye Complies with the IEEE 802.3z/D2 specification, and is class 1
laser eye safety
Receiver
Sensitivity (Avg.) PIN -17 dBm 2
Input Optical Wavelength λ850 nm
Optical Rise/Fall time tr/tf0.36 ns 1
Signal Detect-Asserted (Avg.) PA-17 dBm
Signal Detect-De-asserted (Avg.) PD-30 dBm
Signal Detect-Hysteresis PA-PD0.5 dB
Receiver saturation power PSAT -4 dBm
Notes:
1. These are 20%~80% values
2. The sensitivity is provided at a BER of 1×10-10 or better with an input signal consisting of
1250Mb/s, 27-1 PRBS and ER=9dB.
Mask of the eye diagram for the optical transmit signal

OPT-1250xxxx Series
DELTA ELECTRONICS, INC.
5 Jan., 2008
Rev. 0H
www.deltaww.com
Pin Definition
PIN Symbol Functional description
1 GND Receiver Signal Ground
2 RD (+) Receiver Data Out Non-inverted (LVPECL)
3 RD (-) Receiver Data Out Inverted (LVPECL)
4 SD Receiver Signal Detect (LVPECL or TTL)
5 VccR Receiver Power Supply,
6 VccT Transmitter Power Supply
7 TD (-) Transmitter Data In Inverted (LVPECL)
8 TD (+) Transmitter Data In Non-inverted (LVPECL)
9 GND Transmitter Signal Ground
Pin Descriptions
Pin 1 Receiver Signal Ground, GND
Directly connect these pins to the ground plane.
Pin 2 Receiver Data Out Non-inverted (LVPECL), RD (+)
Receiver Data output Non-inverted (LVPECL), RD (+).
Pin 3 Receiver Data Out Inverted (LVPECL), RD (-)
Receiver Data output Inverted (LVPECL), RD (-).
Pin 4 Receiver Signal Detect (LVPECL/TTL), SD
PECL/TTL logic family. Normal Operation: Logic “1” Output
Fault Condition: Logic “0” Output.
Pin 5 Receiver Power Supply, VccR
Provide +3.3/5V dc power supply.
Pin 6 Transmitter Power Supply, VccT
Provide +3.3/5V dc power supply.
Pin 7 Transmitter Data In Inverted (LVPECL), TD (-)
Transmitter Data Input Inverted (LVPECL), TD (-)
Pin 8 Transmitter Data In Non-inverted (LVPECL), TD (+)
Transmitter Data Input Non-inverted (LVPECL), TD (+)
Pin 9 Transmitter Signal Ground, GND
Directly connect these pins to the ground plane.

OPT-1250xxxx Series
DELTA ELECTRONICS, INC.
6 Jan., 2008
Rev. 0H
www.deltaww.com
Recommend Circuit Schematic for Internal DC Coupled Transceivers
R1=R3=82 ohm (3.3V),68 ohm(5V)
R2=R4=130 ohm (3.3V),191 ohm (5V)
R5=R6=150 ohm (3.3V),270 ohm (5V)
R7=130 ohm (3.3V PECL),82 ohm(5V),NC (TTL)
R8=82 ohm (3.3V PECL),130 ohm(5V),NC (TTL)
C1=C2=C3=C4=C5=C6=C7=100 nF
C8=C9=10uF
L1=L2=1uH

OPT-1250xxxx Series
DELTA ELECTRONICS, INC.
7 Jan., 2008
Rev. 0H
www.deltaww.com
Recommend Circuit Schematic for Internal AC Coupled Transceivers
R1=130 ohm (3.3V PECL),82 ohm(5V),NC (TTL)
R2=82 ohm (3.3V PECL),130 ohm(5V),NC (TTL)
C1=C2=C3= 100 nF
C4=C5=10uF
L1=L2=1uH

OPT-1250xxxx Series
DELTA ELECTRONICS, INC.
8 Jan., 2008
Rev. 0H
www.deltaww.com
Package Outline Drawing (without shielding)
Package Outline Drawing (A type shielding)
Class 1 Laser Product

OPT-1250xxxx Series
DELTA ELECTRONICS, INC.
9 Jan., 2008
Rev. 0H
www.deltaww.com
Package Outline Drawing (B type shielding)
Package Outline Drawing (C type shielding)

OPT-1250xxxx Series
DELTA ELECTRONICS, INC.
10 Jan., 2008
Rev. 0H
www.deltaww.com
Regulatory Compliance
Feature Reference Performance
Electromagnetic Interference
(EMI) FCC Class B
EN 55022 Class B (CISPR 22A)
Radio Frequency
Electromagnetic Field EN 61000-4-3
IEC 1000-4-3
Electrostatic Discharge to the
Duplex LC Receptacle EN 61000-4-2
IEC 1000-4-2
IEC 801.2
Electrostatic Discharge to the
Electrical Pins MIL-STD-883E Method 3015.7
(1) Satisfied with electrical
characteristics of product
spec.
(2) No physical damage
Eye Safety US FDA CDRH AEL Class 1
EN 60950: 2000
EN 60825-1: 1994+A11+A2
EN 60825-2: 2000
CDRH File # 0321539-00
TUV Certificate No. R50032471
Component Recognition Underwriters Laboratories and
Canadian Standards Association Joint
Component Recognition for Information
Technology Equipment Including
Electrical Business Equipment
UL File # E239394

OPT-1250xxxx Series
DELTA ELECTRONICS, INC.
11 Jan., 2008
Rev. 0H
www.deltaww.com
Ordering Information
OPT- 1250X1X2X3X4X5X6X7
X1: Fiber
A: Multi-mode 850nm
B: Single-mode 1310nm
X
5: RoHS Compliant
Blank: Non-RoHS Compliant
R: RoHS Compliant
X2: Power Supply Voltage and SD Level
1: 5.0V, PECL SD Level
2: 3.3V, PECL SD Level
4: 3.3V, TTL SD Level
X
6: Shielding Type & Revision Code
A: New design
B: B type shielding
C: C type shielding
D: A type shielding
X
3:
X4:
Distance
F: 500m, 50/125μmMMF
Q: 10km, 9/125μmSMF
Data Coupling
1: 1x9 SC DC/DC
2: 1x9 SC AC/AC
X
7:Temperature
Blank: 0 to +70 degree C
H: -10 to + 85 degree C
T: -40 to + 85 degree C
Appendix A．Document Revision
Version No. Date Description
0G 2006-09 Release
0H 2008-01
Correct “Total Supply Current”、“TTL SD Output”、“PECL SD
Output”、Recommend Circuit Schematic、Optical Rise/Fall time、
Spectral Width (RMS)、Pin Definition、Package Outline、Order
Information