Delta LD-100E-M22 User manual

Laser Displacement Operating Manual
LD-E Laser Displacement Operating
Manual V1.0
Table of Contents
Chapter 1: Product Profile................................................... 1-1
1.1 Packaging........................................................................................ 1-1
1.2 Part Names and Functions .............................................................. 1-1
1.3 Installation ....................................................................................... 1-2
Chapter 2: Settings and Measurements ......................... 2-1
2.1 Display Operation ............................................................................ 2-1
Chapter 3: Software Operation .......................................... 3-1
3.1 Communication Setting ................................................................... 3-1
Chapter 4: Communication Setting .................................. 4-1
4.1 Communication Address.................................................................. 4-1
4.2 Communication Protocol ................................................................. 4-4
Chapter 5: Specifications .................................................... 5-1
Chapter 6: Safety Precautions........................................... 6-1
Chapter 7: Warranty .............................................................. 7-1

Chapter 1 Product Profile
LD-E Operation Manual
1-1
Chapter 1
Product Profile
1.1 Packaging
The following is included:
1) Laser displacement and cable (optional)
2) Laser label
3) Simple instruction sheet
Laser Label Description
1.2 Part Names and Functions
◎Exterior
Positive Side
Laser light emitting
area
Laser light receiving
area
Panel setting
and display
Ø3 mounting
holes
9 Pin outlet
Laser Radiations: Class 2 Product
Maximum Output: <1mW
Pulse Duration: 0.5ms max.
Wave Length:655nm, IEC 60825-1:2014

Chapter 1 Product Profile
LD-E Operation Manual
1-2
◎Laser Indicator
Indicator Color Description
Laser indicator Blue light Start (laser on)
OUT Green light DO
IN Yellow light DI
Negative Red light Negative
1.3 Installation
◎Dimension (unit: mm)
Laser indicator
DI
DO
Negative

Chapter 1 Product Profile
LD-E Operation Manual
1-3
◎Wiring Instructions

Chapter 1 Product Profile
LD-E Operation Manual
1-4
◎Caution on Mounting Direction
For best product performance, please note the following instructions when installing products.
1) When products cling to devices, install the products in parallel with the devices to assure product
performance.
2) When the shape of an inspection object is extrusive, ensure the product's lighting route is vertical to
the inspection object's path to assure product performance.

Chapter 2 Settings and Measurements
LD-E Operation Manual
2-1
Chapter 2
Settings and Measurements
2.1 Display operation
◎Display instruction

Chapter 2 Settings and Measurements
LD-E Operation Manual
2-2
Basic teaching (2 point teaching)
The teaching point of second point is greater than the first point 2 hysteresis (Hys) size.
1. 2.
1. In a state of background, press .
2. When there is a detection object, press
When the object can be detected
When the object cannot be detected

Chapter 2 Settings and Measurements
LD-E Operation Manual
2-3
Single point teaching (window comparison mode)
Single point teaching is used for the distance between the reference plane of the detection object, the
method of setting the upper and lower limits, and the output between the upper and lower limits.
After the reference plane of the detection object is taught
1_SL = The height of the detection object minus 2 times the hysteresis
2_SL = The height of the detection object plus 2 times the hysteresis
1. With the detection object, press twice. (1st time: TEACH mode, 2nd time: teaching)
2. After teaching, press once to leave.

Chapter 2 Settings and Measurements
LD-E Operation Manual
2-4
2 point teaching (window comparison mode)
Execute 2 point teaching and set the reference value.
First, come to the advanced setting, set the detection output to _P_2 (2-point teaching)
When executing, use detection objects with different distances (P-1, P-2)
1. When there is a detection object (P-1), press the first to enter the teaching mode, and press the second
2. With the detection object (P-2), press the third
When the object can be detected, press the fourth to leave.
When the object cannot be detected, press the fourth to leave.

Chapter 2 Settings and Measurements
LD-E Operation Manual
2-5
3 point teaching (window comparison mode)
Before executing 3 point teaching, set the reference value 1_SL between 1st time and 2nd time
and set the reference value 2_SL between 2nd time and 3rd time.
First, come to the advanced setting, set the detection output to _P_3 (3-point teaching)
1. When there is a detection object (P-1), press the first to enter the teaching mode, and press the second
2. With the detection object (P-2), press the third
3. With the detection object (P-2), press the fourth
When the object can be detected, press the fifth to leave.
When the object cannot be detected, press the fifth to leave.