Delta AG6248C User manual

Delta Networking – Agema Family
AG6248C Power-Over-Ethernet Switch
Installation Guide

ii
AG6248C Power-Over-Ethernet Switch
Copyright
All specications and gures are subject to change without prior notice. Actual products may look
different from the photos.
All trademarks and logos mentioned in this guide are the properties of their respective holders.
Copyright © Delta Products Corporation. All rights reserved.
Regulatory and Safety Information
This product has been tested in accordance to, and complies with the following safety standards and
electromagnetic compatibility (EMC) inspection standards.
Emissions
Applicable standard
• AS/NZS CISPR 22: Class A
• ICES-003, Issue Class A
• EN 55022: Class A
• VCCI Class A
• FCC CFR 47 Part 15, Subpart B Class A
Safety
Applicable standard
• EN 60950-1, Second Edition
• UL/CSA 60950-1, Second Edition
• IEC 60950-1, Second Edition Including All National
Immunity
Applicable standard
• EN 300 386, EMC for Network Equipment
• EN 55024:
• EN 61000-3-2: Harmonic Current Emissions
• EN 61000-3-3: Voltage Fluctuations and Flicker
• EN 61000-4-2: ESD
• EN 61000-4-3: Radiated Immunity
• EN 61000-4-4: EFT
• EN 61000-4-5: Surge
• EN 61000-4-6: Low Frequency Conducted Immunity
• EN61000-4-8: Power Frequency magnetic eld
• EN61000-4-11: Voltage dips and interruptions
RoHS
Applicable standard All AG-Series components are EU RoHS compliant
Warning: Fiber Optic Port Safety
When using a ber optic port, never look at the transmit laser while it is powered
on. Also, never look directly at the ber TX port and ber cable ends when they are
powered on.

iii
Table of Contents
Table of Contents
Chapter 1: Introduction -------------------------------------------------------------------1
1.1 Overview ------------------------------------------------------------------------------------ 1
1.2 Package Content -------------------------------------------------------------------------- 1
1.3 Features ------------------------------------------------------------------------------------- 2
Chapter 2: Appearance and Mechanism --------------------------------------------3
2.1 Product Overview ------------------------------------------------------------------------- 3
2.2 LED Identication ------------------------------------------------------------------------- 4
2.3 System Requirements ------------------------------------------------------------------- 7
2.4 Data Center Deployment ---------------------------------------------------------------- 8
2.5 Power Supply Modules ------------------------------------------------------------------ 9
2.6 Fan Tray Module -------------------------------------------------------------------------- 9
Chapter 3: Installation ------------------------------------------------------------------- 10
3.1 Mounting -----------------------------------------------------------------------------------10
3.2 Installing an Optional SFP+ Transceiver -------------------------------------------12
3.3 Connecting to the Console Port ------------------------------------------------------13
3.4 Connecting to a Power Source -------------------------------------------------------13
Chapter 4: Making the Network Connections ----------------------------------- 15
4.1 Twisted-pair Connections --------------------------------------------------------------15
4.2 Fiber Optic Connections ---------------------------------------------------------------16
4.3 Ethernet Cabling -------------------------------------------------------------------------16
Appendix 1 : Technical Specifications--------------------------------------------- 17
Appendix 2 : Warranty------------------------------------------------------------------- 19
Limited and Support Warranty -------------------------------------------------------------19
Technical Support -----------------------------------------------------------------------------19

1
AG6248C Power-Over-Ethernet Switch
Chapter 1: Introduction
1.1 Overview
AG6248C PoE has 48 10/100/1000BaseT copper ports plus 2 combo SFP ports and 2 SFP+
ports. Each copper port supports auto-sensing and auto negotiation. To further simplify
network setups, all ports also automatically sense half- or full-duplex connections for high-
speed server or switch-to-switch congurations. The AG6248C PoE provides power and data
from a single point, using Power over Ethernet (PoE) over a single Cat-5 cable. All of these
48 10/100/1000Base-T ports can supply industry-standard IEEE 802.3at power over Ethernet.
Advanced auto-sensing algorithm gives power only to 802.3at/802.3af complied end devices,
preventing of damaging proprietary PoE or non-PoE equipment.
1.2 Package Content
After unpacking this switch, check the contents to be sure you have received all the
components. Then, before beginning the installation, be sure you have all other necessary
installation equipment.
•AG6248C PoE switch
•1 x AC power supply
•Rack-mounting kits
•2 x Velcro strips
•Installation guide
If any item is missing or damaged, contact the vendor immediately, see “Technical Support”.

2
• IntroductionChapter 1
1.3 Features
The following lists the main features of the AG6248C PoE switch:
•48 x 10/100/1000 BASE-T ports
•2 x combo SFP ports
•2 x 10GbE SFP+ ports
•48 x 1G RJ45 ports are to support PoE+
•1-12 of RJ45 ports capable of UPoE
•1 x Management port
•1 x Console port (RJ-45 type)
•1 x USB port for system le access
•Hot plugging redundant power supply support
•1 Fan tray module (2 Fans)
•Power supply LED / System / FAN status LED indication
•1 x 1100w AC power supply
•Temperature monitoring. (TMP75)
•Software readable thermal monitor
•Standard 1U chassis high and Rack mountable in standard 19” racks
•Automatic address learning function to build the packet-forwarding information table. Up to
32K MAC address table.
•4MB of packet buffer memory
•Support Jumbo Frame up to 12Kbyte
•Pre-loaded with Open Network Install Environment (ONIE) for automated loading of
compatible SwitchOS software

3
AG6248C Power-Over-Ethernet Switch
Chapter 2: Appearance and Mechanism
2.1 Product Overview
2.1.1 Front View USB port
Combo SFP port x 2
Management port
10/100/1000BaseT port x 48
Console port
10GbE SFP+ port x 2
(Figure 2-1: Front View)
2.1.2 Rear View
Redundant PSU x 2
Fan tray slot (2 Fans per tray)
(Figure 2-2: Rear View)
NOTE:
The switch supports up to two PSUs. However, it is shipped with one power supply
pre-installed in the rear panel of the switch. You may purchase an additional PSU for
redundancy.

4
• Appearance and MechanismChapter 2
2.2 LED Identification
This section provides an overview of the front and rear LEDs.
2.2.1 Front LEDs
Upper 1G BASE-T port LED
Lower 1G BASE-T port LED
1G combo SFP port LED
Console port LED
Management port LED
10G SFP+ port LED
Power 1/ Power 2 LED
Status LED
Fan LED
(Figure 2-3: Front LED Identification)
LED Description
STATUS LED
• Solid Green – Normal operation
• Blinking Green – Booting in progress
• Solid Red – Critical system error
• Blinking Red – Non-critical system error (FAN failure, power supply failure)
Power 1 LED
• Off – Power failure or no power
• Solid Green – Operating normally
• Blinking Green – Locator function is enabled
Power 2 LED
• Off – Power failure or no power
• Solid Green – Operating normally
• Blinking Green – Locator function is enabled
FAN LED • Solid Green – FAN operating normally
• Solid Red – FAN failure or not inserted

5
AG6248C Power-Over-Ethernet Switch
LED Description
1G BASE-T ports
LEDs
Link/SPD LED (left)
• Off – No link
• Solid Green – A valid link at 1000Mbps
• Solid Yellow – A valid link at 10/100Mbps
POE/ACT LED (right)
• Off – No Activity, PoE is powered OFF
• Blinking Green – Activity, PoE is powered OFF
• Blinking Yellow – Activity, PoE is powered ON
• Solid Yellow – No Activity, PoE is powered ON
1G combo SFP
ports LEDs
Link/SPD LED (left)
• Off – No link
• Solid Green – A valid link at 1000Mbps
• Solid Amber – A valid link at 100Mbps
ACT LED (right)
• Off – No Activity
• Blinking Green – Activity
10G SFP+ ports
LEDs
Link/SPD LED (left)
• Off – No link
• Solid Green – A valid link at 10Gbps
• Solid Amber – A valid link at 1Gbps
ACT LED (right)
• Off – No Activity
• Blinking Green – Activity
Management port
LEDs
Link/SPD LED (left)
• Off – No link
• Solid Green – A valid link at 1Gbps
• Solid Amber – A valid link at 1Mbps or 10Mbps
Act LED
• Off – No link
• Blinking Green – Activity, transmitting or receiving packet at this port
Console port LED
Link/SPD LED
• Off – No link
• Solid Green – A valid link

6
• Appearance and MechanismChapter 2
2.2.2 Rear LEDs
Power Supply LED
(Figure 2-4: Rear LED Identification)
LED Description
Power Supply
LEDs
• Off – No power
• Solid Green – Power is ok
• Solid Red – Power supply is detected but is inadequate

7
AG6248C Power-Over-Ethernet Switch
2.3 System Requirements
Component Requirement
System requirements
Switch fabric capacity Non-blocking full wire speed on all packet sizes
Forwarding architecture Store and forward or cut-through
Port packet forwarding rate
• 14880pps (10Mbps)
• 148800pps (100Mbps)
• 1488000pps (1000Mbps)
• 14880000pps (10Gbps)
MAC address entries
supported 32K entries
Memory type 4 MB buffer memory
OOB port 10/100/1000Mbps, auto sensing, auto negotiation
MAC Address Aging
Support
• 1,000,000 seconds programable
• Default 300 seconds
Spanning Tree Support
• Support IEEE802.1d STP
• Support IEEE802.1s MSTP
• Support IEEE802.1w RSTP
Storm Control
• Rate control based on packet / byte
• Unknown unicast (DLF) packet
• Broadcast packet
• Known & unknown L2MC packets
• Known & unknown IPMC packets
• Enable individual threshold per port
Port requirements
Speed Capability per Port 100/1000Mbps Auto-Sensing
Full-Duplex Flow Control Support the IEEE 802.3x PAUSE frame