Deltran Hyperion 043-1002-HY-WH User manual

1


Instruction Manual
3-in-1 Vehicle Repair Kit
Electric Jack/Inflator Pump/Electric Impact Wrench
P/N 043-1002-HY-WH
Read this material before using this product.
Failure to do so can result in serious injury.
Save this manual.
2

CONTENTS
Important Safety Instructions and Warnings……………….. 3
Product Specifications………………………………………….. 5
Product Overview………………………………………………… 6
Electric Jack Features/Operation..……………………………. 6
Electric Impact Wrench Features/Operation..………………. 7
Trouble Shooting…………………………………………………. 8
Customer Service………………………………………………… 8
Warranty…………………………………………………………… 8

3

IMPORTANT SAFETY INSTRUCTIONS & WARNINGS
1) SAVE THESE INSTRUCTIONS – This manual contains important safety and
operating instructions for the 3-in-1 Vehicle Repair Kit, P/N 043-1002-HY-WH
2) Read all warning labels and instructions. Operating instructions must be
understood before using equipment. Never remove labels from equipment.
Replace missing, worn or damaged labels. Always wear safety goggles and
protective clothing when using hydraulic equipment.
3) Fully support each jack or ram at its base.
Every jack or ram, whether used individually or in a system, should be completely
supported on a solid, firm, non-sliding foundation capable of supporting the load.
4) Center the load on the lifting point.
The load must be centered on the ram, or equally distributed on multiple rams.
Off-center loading can result in the ram slipping out and loss of the load.
5) Block or crib load as it rises.
Place blocking or cribbing under the load as you raise it. Each time you raise it
higher, insert more blocking. Position yourself in a manner that will keep you
clear of the load, and will not allow your hands or other body parts between the
load and the cribbing.
4

6) Do not use rams as permanent supports.
Hydraulic rams are not meant to be used as permanent supports, but are
designed to lift and lower. If you need to hold the load for any length of time,
place blocking or cribbing under the load.
7) Apply parking brake and chock tires before lifting vehicle.
8) Do not exceed rated capacity.
9) Before use, read manufacturer’s instruction manual for the vehicle (or object)
you will lift.
10) Keep clear of load while lifting and lowering.
11) Lift vehicle only at manufacturer-recommended locations.
12) Inspect before every use; do not use if parts loose or damaged.
13) Do not work under the vehicle without properly supporting the vehicle with jack
stands.
14) Avoid dangerous oncoming traffic. Use the Jack as far away from the roadside
as possible.
15) Before lowering the Jack, remove all tools and equipment from under the
vehicle.
16) The warnings, precautions, and instructions discussed in this manual cannot
cover all possible conditions and situations that may occur. The operator must
understand that common sense and caution are factors, which cannot be built
into this product, but must be supplied by the operator
17) This product is not designed to be used by children.
18) Do not modify the equipment in anyway.
19) Do not use any accessories that are not recommended by the manufacture.
20) Hyperion® is not responsible for any loss caused by an accident or for
providing any support regarding the outcome.

5

SPECIFICATIONS
Electric Jack
Input Voltage 12 Volt DC
Rated Power 150 Watts
Maximum Current 13 Amps
Fuse 15 Amp, 250 Volt
Maximum Lifting Weight 3 Tons (6000 pounds)
Lifting Height Range 6-17½ inches (155 – 444mm)
Working Temperature 5 - 122°F (-15 - 50°C)
Inflator Pump
Input Voltage 12 Volt DC
Inflation Speed 77lbs/min. (35L/min)
Maximum Current 10 Amps
Maximum Pressure 150PSI
Length of Air Hose 23½ inches
Electric Impact Wrench
Input Voltage 12 Volt DC
Rated Power 100 Watts
Maximum Current 10 Amps
Maximum Torque 250 pounds (340N.M)
Weight 4.4lbs (2.0Kg)
 6

PRODUCT OVERVIEW
Below is a list of items that should be included in your retail box:
1) Electric Jack/Inflator Pump
2) Electric Impact Wrench
3) Plastic Carry Case
4) 12VDC Power Cable
5) Safety Hammer
6) Reversible Sockets (2)
7) Battery Clamp Connecting Cable
8) Inflation needle and hose connectors (3)
9) Fuse (2)
10) Hex wrench
11) Gloves (1 pair)
ELECTRIC JACK FEATURES/OPERATION
Right side pocket contains:
1) Inflation needle and hose connectors (3)
2) Fuse (2)
3) Hex wrench

 7

Left side pocket contains:
1) Air Hose
Switch Operations:
 8

Safety Release Valve Operation:
1) Remove the dustproof plug to expose the hex screw.
2) With the supplied hex wrench, loosen the hex screw until the jack starts to
descend.
3) Once descended remove from under vehicle.
4) Then tighten the hex screw and replace the dustproof plug.
Adjusting Screw Operation:
1) Once the jack is placed under the vehicle in the correct position the
adjusting screw on top the ram can be un-screwed so that the pressure
ram does not have to travel as far to lift the vehicle.

9

Electric Jack Operation
1) Before operating the jack, read and understand all the important safety
instructions and warnings contained in the front of this manual.
2) Also refer to any vehicle owner’s guide before lifting any vehicle.
3) Connect the power adapter to the vehicles 12 volt power outlet or use the
supplied alligator clips and female adapter and connect to a 12volt battery.
4) Connect the two pin plug to the power port on the Jack.
5) Press the Jack ram power switch (shown in the diagram on page 7) down
to the On position.
6) Then press the Jack Ram switch down to activate the Ram upwards.
7) Once the Ram has reached its desired or maximum height return the Jack
Ram switch to its Off position.
8) To lower the Jack Ram press the switch in the down direction.
9) Once down turn the switch to the Off position to turn the Jack Ram Off.
Inflator Pump Operation
1) Connect the power adapter to the vehicles 12 volt power outlet or use the
supplied alligator clips and female adapter and connect to a 12volt battery.
2) If any valve adapters are required check the right side pocket.
3) Connect the hose to the valve.
4) Also refer to any vehicle owner’s guide before inflating any tires.
5) Press the inflator switch into the On position and inflate to the required
value by watch the pressure gauge.
 10

ELECTRIC IMPACT WRENCH FEATURES/OPERATION
Electric Impact Wrench Operation
1) Connect the power adapter to the vehicles 12 volt power outlet or use the
supplied alligator clips and female adapter and connect to a 12volt battery.
2) Connect the two pin plug to the power port on the Wrench.
3) To loosen (Anti-clockwise “L”) press the switch down to the left.
4) Hold the switch down for a second or more then the torque will activate.
5) To tighten (Clockwise “R”) press the switch down to the right.
6) After using this impact wrench always check the tightness of lug nuts using
a torque wrench set to the correct setting (see owner’s manual).

11

TROUBLE SHOOTING
PROBLEM POSSIBLE CAUSE SOLUTION
Electric jack/inflator
does not have
power
The switches are set in the
incorrect position Set switches to correct position
The power cable is not
connected securely to the
vehicles power outlet
Check connection and ensure
the red LED indicator is on.
The LED indicator on the
power cable is not on and
the internal fuse is blown
Replace the 15A fuse with one
that is supplied in the left
pocket
The power cable is
dama
g
ed Replace the cable
The vehicles power outlet
fuse is blown Refer to the vehicles owner’s manual and replace the fuse
The vehicles battery is dead Charge or replace the battery
The inflator is
running but will
not inflate the
tire
The hose in not properly
attached to the valve stem Check connection
The tire is completely
deflated and the seal
between the tire and wheel
rim is leakin
g
ai
r
Jack up the vehicle to release
the pressure on the tire rim.
The vehicles battery is too
low Recharge/replace the battery
The inflator hose is
damaged Repair the hose
The jack motor is
running but will
not lift the
vehicle
The load is too heavy Relocate the jack to a different
lifting point
The safety valve screw is
loose Tighten the screw
The jack is
taking a long
time to lift the
load
The vehicle’s battery is too
low Recharge/replace the battery
12

CUSTOMER SERVICE
WARRANTY
For customer support please visit Deltran-Global.com/Hyperion. You can also
call our customer service hotline [phone]
The Hyperion ® Vehicle repair kit comes with a twelve (12) month limited
warranty against defects or failure (within one (1) year of purchase).
THIS LIMITED WARRANTY IS VOID under the following conditions:
1) The product is misused, subjected to careless handling, or operated under
conditions of extreme temperature, shock, or vibration beyond our
recommendations for safe and effective use.
2) The product is misused, subjected to careless handling, or operated under
conditions of extreme temperature, shock, or vibration beyond our
recommendations for safe and effective use.
3) The product is disassembled or repaired by anyone who is not an
authorized service representative.
4) The product was purchased from an unauthorized source. Warranty is not
transferable from the original purchaser.
5) Any physical damage to the Vehicle repair kit or any accessory after
purchase.
6) Any modifications to the 3-in-1 vehicle repair kit.