Denon POA-3012CI - Multi-Zone Audio Distribution Power... User manual

DENON
MULTI CHANNEL POWER AMPLIFIER
POA-3012CI
Owner's Manual
Bedienungsanleitung

ENGLISH DEUTSCH
oSAFETY PRECAUTIONS
ARISK OF ELECTR~C SHOCK A
~ '--_-=D:....;:O::....:N=O:::..T-=--O=.:....;PE=N-=--_.....J ~
CAUTION:
TO REDUCETHE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK).
NO USER·SERVICEABLE PARTS INSIDE.
REFER SERVICINGTO QUALIFIED SERVICE PERSONNEL.
A
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of
uninsulated "dangerous voltage" within the product's enclosure
that may be of sufficient magnitude to constitute arisk of electric
shock to persons.
A
The exclamation point within an equilateral triangle is in. tended
to alert the
user to the presence of important operating
and maintenance (servicing) instructions in the literature
accompanying the appliance.
WARNING:
TO REDUCETHE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSETHISAPPLIANCETO RAIN OR MOISTURE.
CAUTION:
• The ventilation should not be impeded by covering the ventilation
openings with items. such as newspapers, tablecloths, curtains,
etc.
• No naked flame sources, such as lighted candles, should be
placed on the unit
• Observe and follow local regulations regarding battery disposal.
•
Do not expose the unit to dripping or splashing fluids.
•Do
not place objects filled with liquids, such as vases, on the
unit
ACHTUNG:
• Die Beluftung sollte auf keinen Fall durch das Abdecken der
Beluftungsbffnungen durch Gegenstande wie beispielsweise
Zeitungen, Tischtucher, Vorhange o. A behindert werden.
• Auf dem Gerat sollten keinerlei direkte Feuerquellen wie
beispielsweise angezundete Kerzen aufgestellt werden.
• Bitte beach ten Sie bei der Entsorgung der Batterien die brtlich
geltenden Umweltbestimmungen.
•Das Gerat so lite keiner trapfenden oder spritzenden Flussigkeit
ausgesetzt werden.
• Auf dem Gerat sollten keine mit Flussigkeit gefUliten Behalter
wie beispielsweise Vasen aufgestellt werden.
I
IMPOTANT SAFETY
INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings.
Install
in accordance with the manufacturer's instructions.
8. Do not install near any heat sources such as radiators, heat registers,
stoves,
or other apparatus (including amplifiers) that produce heat
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug
has two blades with one wider than the other. Agrounding
type plug
has two blades and athird grounding prong. The wide blade or the
third prong
are provided for your safety. If the provided plug does not fit into
your outlet. consult
an electrician for replacement of the obsolete outlet
10. Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table (I)
specified by the manufacturer, or sold with the apparatus.
When acart
is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
.,
13. Unplug this apparatus during lightning storms or when l~
unused for long periods of time. ~-
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus
has been damaged in any way,
such as power·supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.
CAUTION:
To completely disconnect this product from the mains, disconnect
the plug fram the wall socket outlet
The mains plug is used to completely interrupt the power supply to
the unit and must be within easy access by the user.
VORSICHT:
Um dieses Gerat vollstandig von der Stromversorgung abzutrennen,
ziehen Sie bitte den Stecker aus der Wandsteckdose.
Der Netzstecker wird verwendet, um die Stromversorgung zum
Gerat vbllig zu unterbrechen; er muss fur den Benutzer gut und
einfach zu
erreichen sein.
FCC INFORMATION (For US customers)
1, COMPUANCE INFORMATION
Product Name: Multi Channel Power Amplifier
Model Number:
POA·3012CI
This product complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
(1) this product may not cause harmful
interference,
and (2) this product must accept any interference received,
including interference that may
cause undesired operation.
Denon Electronics (USA), LLC
(a 0 & M Holdings Company)
100 Corporate Drive
Mahwah,
NJ 07430·2041
Tel. [phone]
2. IMPORTANT NOTICE: DO NOT MODIFY THIS PRODUCT
This product, when installed as indicated in the instructions contained
in this manual, meets FCC requirements. Modification not expressly
approved
by DENON may void your authority, granted by the FCC, to use
the product
3. NOTE
This product has been tested and found to comply with the limits for
a
Class Bdigital device, pursuant to Part 15 of the FCC Rules. These
limits
are designed to provide reasonable protection against harmful
interference
in aresidential installation.
This product generates,
uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in aparticular installation. If this
product does
cause harmful interference to radio or television reception,
which
can be determined by turning the product OFF and ON, the user
is encouraged to try to correct the interference by one or more of the
following measures:
•Reorient
or relocate the receiving antenna.
•Increase the separation between the equipment
and receiver.
•Connect the product into
an outlet on acircuit different from that to
which the receiver
is connected.
•Consult the local retailer authorized to distribute this type of product
or
an experienced radio!TV technician for help.
ThiS Class Bdigital apparatus complies With Canadian ICES-003.
Cet appareil numerique de la cia sse Best conforme a la norme NMB-003 du
Canada.

DEUTSCH ENGLISH
oNOTE ON USE IHINWEISE ZUM GEBRAUCH oFor Europe model
DENON Europe
Division
of D&M Germany GmbH
An der Landwehr
19, Nettetal,
0-41334 Germany
DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product. to which this declaration relates, is in
conformity with the following standards:
EN60065, EN55013, EN55020, EN61000-3-2
and EN61000-3-3.
Following the provisions of 2006/95/EC and 2004/108/EC Directive.
UBEREINSTIMMUNGSERKLARUNG
Wir erklaren unter unserer Verantwortung, da~ dieses Produkt, auf das sich diese Erklarung bezieht,
den folgenden Standards entspricht:
EN60065, EN55013, EN55020, EN61000-3-2 und EN61000-3-3.
Entspricht den Verordnungen der Direktive 2006/95/EC und 2004/108/EC.
• Do not let foreign objects into the unit.
• Lassen Sie Kaine fremden Gegenstande in
das Gerat Kammen.
• Keep the unit free from moisture. water,
and dust.
•Halten Sie das Gartit von Feucht~kelt.
Wasser und Staub fern. f----------------j
• Avoid high temperatures.
Allow for sufficient heat dispersion when 1- --1
installed in a rack.
•Vermeiden Sie hohe Temperaturen.
Beadlten SIB. dass eine ausrelchende
Beluftung gewahrleistet wird, wenn das
Garat auf ein Regal gestellt wird.
HINWEIS ZUM RECYCLING:
Das Verpackungsmaterial dieses Produktes ist zum Recyceln geeignet und kann wieder verwendet werden. Bine
entsorgen Sie aile Materialien entsprechend der 6rtlichen Recycling-Vorschriften.
Beachten
Sie bei der Entsorgung des Gerates die 6rtlichen Vorschriften und Bestimmungen.
Die Batterien durfen nicht
in den Hausmull geworfen oder verbrannt werden; bitte entsorgen Sie die Batterien gemaB
der 6rtlichen Vorschriften.
Dieses Produkt und das im Lieferumfang enthaltene Zubeh6r (mit Ausnahme der Batterien!) entsprechen der WEEE-
Direktive.
-
ANOTEABOUT RECYCLING:
This product's packaging materials are recyclable and can be reused. Please dispose of any materials
in accordance with the local recycling regulations.
When discarding the unit, comply with local rules or regulations.
Batteries should never be thrown away or incinerated but disposed
of in accordance with the local
regulations concerning battery disposal.
This product and the supplied accessories, excluding the batteries, constitute the applicable product
according to the
WEEE directive.
• 00 not let insecticides. benzene, and
thinner come in contact with the unit.
• Lassen SIB das Gerat nidlt mit lnsektiziden,
Benzin oder Verdunnungsmitteln In
Beruhrung kommen.
• Never disassemble or modIfy the unit in
any way.
• Ne jamais demanter au modifier I'appareij
d'une maniere au d'une autre.
.-.J\\~II
U:i:~~\w
, 0: .,...,...
• (For apparatuses with ventilation holes)
• Unplug the power cord when not uSing the
unit for long periods of time.
•Wenn das Gerat langere Zeit nicht
verwendet werden soli, trennen Sie das
Netzkabel vom Netzstecker.
• Do not obstruct the ventilation holes.
• Decken Sie den Luftungsbereich nicht abo
• Handle the power cord carefully.
Hold the plug when unplugging the cord.
• Gehen Sie vorslchtlg mit dem Netzkabel
urn.
Halten Sle das Kabel am Stecker, wenn Sle
den Stecker herauszlehen.
n

ENGLISH
~
:0 I
jl *]
I
! ; Wall
'~/..w..w&ffmff;/,w/ffi;~
Cautions on Handling
Cautions on Installation
•Before turning the ON/STANDBY switch on
Check once again that all connections are correct and that there are
no problems with the connection cables.
•Power
is supplied to some of the circuitry even when the unit is
set to the standby mode. When traveling or leaving home for long
periods of time. be sure to unplug the power cord from the power
outlet.
•About condensation
II there
is amajor difference in temperature between the inside of
the unit and the surroundings. condensation (dew) may form on
the operating parts inside the unit. causing the unit not to operate
properly.
II this happens. let the unit sit for
an hour or two with the power
turned off and wait until there is little difference in temperature
before using the unit.
•Cautions on using mobile phones
Using amobile phone near this unit may result
in noise. If so. move
the mobile phone away from this unit when it
is in use.
•Moving
the unit
Turn off the power and unplug the power cord from the power
outlet.
Next. disconnect the connection cables to other system units before
moving the unit.
•Note that the illustrations
in these instructions may differ from the
actual unit for explanation purposes.
Note:
For proper heat dispersal. do not install this unit in aconfined
space.
such as abookcase or similar enclosure.
Q) Owner's manual 1
@Warranty Ifor North America model only).. 1
<1J Service station list.. .. 1
®Power cord... . 1
Cord length: 0North America model: 6.6 ft /2.0 m
•Europe model: 5.2 ft /1.6 m
Getting Started
I Oper1!u,on, . • 1
Tuming the Power On ··17
Check the Status of Each Channel .. · .. · .. · ·· ..·· ·· .. ··· .. · .. · 17
Other Operations············· .. ················ .. ····· .. · .. · .. ···· .. ···· .. ········ .. ······17
Other Operations During Playback.. ..· · 17
Operating the POA-3012CI Using aBrowser (Web control) 17, 18
Resetting the Microprocessor· ···· · .. ··18
Accessories
Thank you for purchasing this DENON product. To ensure proper
operation. please read this owner's manual carefully before using the
product.
After reading them. be sure to keep them for future reference.
Check that the following parts are supplied
with the product.
I r~~ClOtln9~';+;',t;}~\i;iF·';;'·,:·,·,··~;;:,·'r,;;i;·;·; .·)."···,··,,,:;·:··:·,'<;'·.;A9 '1
1·§p4K;i[IC;oI~···;··:··;~;;;:;L;;;., .. ,., ;..........•. ;.: ,.; :::."i', ;.; 19,1
·······1
1
······1
········2
··2
3
'-0"
................... ········4
.................... ·······4
········4
··.. ·········5
Accessories·· .
Cautions on Handling ..
Cautions on Installation··
Part Names and Functions
Front Panel·
Rear Panel··
Preparations········· .
Before Connecting .
Cables Used for Connections
Speaker Connections·····
Connection Method
When Outputting
2Channels From One ZONE ·······5
Connection Method for BRIDGED Output ... ····5.6
Input Connections ···· .. ······· .. ····7
BUS INPUT Connections . ··· .. ·············7
AUDIO INPUT Connections ··················7
Connections to Other Devices···· . 8
ETHERNET Connections
··· .. ···· .. ············8
External controller ·····
.. ·······9
• RS-232C Connector····· 9
•Trigger output jack· ········· .. · .. ·········· .. ··········9
•Master trigger input jack·· ··· .. ·········9
•ZONE trigger input jacks············· ··········9
Connecting the Power Cord········ 10
Once Connections are Completed··· . 10
Contents
Example of Displav of DefaultValues 10
Operations· . 10
Menu Map·· .. ·· ·11.12
Main Setup ····13
DVOLUME CONTROL · .. ·· .. · .. · .. 13
DINPUT SELECT .·13
II LOW CUT FILTER···· .. ·················· .. ···· .. ················ .. · 13
BOPERATION MODE· 13
iii ZONE TRIGGER ON MODE ·14
II DIMMER MODE ···14
•POWER CONFIGURATION ······14
Network Setup.. . 15
DNetwork Information ·······15
DNetwork Setup ···········15. 16
Option Setup·· .··········16
DMaintenance ··16
DFirmware Update ······16
LGetting Started
----{
1

ENGLISH
Part Names and Functions
For bunons not explained here, see the page indicated in parentheses ( ).
FrontPanel
O-CD
DEADAI
I
.. ----- --- ----- __ _ -- _--_ --- ..
,'1 2 3 4 5 ,'\
!© © © © © ©i
\'''''''_''._'''''''''''' ... ... __ ~ ...... __ ...... __ ......... ... __ ......... _"J
[
1
. .. (17)
......... (17)
.. (17)
oPower operation button
(ON /STANDBY)
..
f) Power indicator· .
.Display· .
CD Infonnation display
Displays present status information and Setup
menu etc.,
GZONE select buttons (10)
oZONE operation mode indicators (6, 13)
oSETUP button . .. (10)
8DISPLAY button .(17)
oSELECT /ENTER knob ... .(10)
oV(Down) button (10)
4i> /:;. (Up) /RETURN button (10)
2

ENGLISH
IIRear Panel
4~ 4')
4~ 0
4'
0
-
,?l
'---
~
'.-J
,""'M$1IIlIJ'I""'"
~O
O~
-TRlGG£llIi :
DC 3-JOV TRIGG£II OIIT: DC 12Y 250mA M l.
~.~ .. ~~
~JIi ________ •
••••••••• IllIlllif.R.IIL._ •••••••
••••• _ •• .lIll~ •• __ •••
._ •••••• _~JIi •••••••••
• •••••••• IllW'.IUIIL_ ••• __ ••
• ••••••• JJIIGGflIJ:
c..@ ............ ........... @ ...........
............ @ ..... _ .. _ ..
.......... _@ ............
. .......... @ .... _ .... _.
............ @)
•••• .I&1!IiiI!lI._.'
(ej'="O";'
.......... _ ........ _ ................
_ .. _ .... _ .. _ ... -- ...... _ .... - -- ............
.. --------- ..... -----------_ .....
..... _-_ ............. _---_ ...... _--_ ..
.. .......... _ ........... _ ..............
~l @1i@~
30=0
45
O~~O 67
0=0
89
0=0
1011
0=0~2
1 rul •I
~,lqg~~_J~ .. )t ... _)
" ............ - .. --------- - .. - .....
............................ - ...................
.......... _-_ ... _- ....... __ ....... _--
-------------- _ .. _ .. -_ .. __ .. _-
........................ ----_ ...........
.. ................................... -_ .... '
BRIDGED BRIDGED BRIDGED BRIDGED
BRIDGED BRIDGED
.~
ACIN
in
--i ZONE 1 t---- --i ZONE 2 t---- --i ZONE 3 t----
--i ZONE 4 t---- --i ZONE 5 t---- --iZONE6t----
....
-Ld
0
SPEAX£R SYSTEMS SPEAX£R SYSTEMS SPEAX£R SYSTEMS SPEAXER SYSTEMS SPEAX£R SYSTEMS
SPEAXER SYSTEMS
BRIDGED - BRIDGED + BRIDGED - BRIDGED + BRIDGED - BRIDGED +
BRIDGED -
BRIDGED +
BRIDGED - BRIDGED + BRIDGED - BRIDGED +
~
(®)'~"(®)'"
.. _ .. _ .................. _ ........ -- .. _ .... _ .. -
......... ------- ................... _---_ ..
---_ .... _ ...... _--_ ............. _----- _ .......... - ---_ ............... --_ .. -- ......
··(@)··~·(®)·1
@)o@) @)o@) @)o@)
@)o@)
-$
@]
°0
00
1: 2345 6 7 8 9
10
11 .2
00
t~ .. ~ .. ~ ...
... ~.~ .. ~ ....
... ~ .. ~ .. ~ ... ..~ .. ~-~ ... ... ~ .. ~ .. ~ ....
@)o@)j
0
RS·232C
lIAlGHT CA8lf ....
_-------_ ............'
SPEAKER IMPEDANCE NORMAL: 4-16Q BRIDGED: 8-16 Q
... --II
I-~
-=
0 t~
4)
0
······(8)
.. (9)
oETHERNET connector·
•RS-232C
connector
•Speaker tenninals
(SPEAKER SYSTEMS) . (5)
oAC inlet lAC IN) (10)
oAUDIO INPUT connectors·· (7)
3
oTRIGGER IN jacks· (9)
8MASTERTRIGGER OUT jack·· (9)
eBUS INPUT connectors··· (7)
oBUS OUTPUT connectors···· (7)
~ MASTERTRIGGER IN jack (9)

ENGLISH
Preparations I
'Cables Used forConnectiC)ns
Input
Output
Audio signal:
~ Output I
(Input r
Speaker cables
.• Si9n{lldi~ .
Stereo pin-plug cable
Pin-plug cable
Ethernet cable
(Black) 0
(Black) 0
Audio input connections
(Black) 0 9[]::=-----::DlP G
Businput/output connections (stereo)
Networic connections
o cmJl ..... ---~ 0
Speaker connections
: )~iiiiiiiiiiiiiii( +
Select the cables according to the equipment being connected.
c ...... S_e_lect __ th_e_in....:p_u_t_te_rm_in::-a_l_to_u_se_. )
I Each Zone input connectors or
..". BUS input connectors.
J"'NPlITSElECT" -"'''' 131
CSet the input
source. )
~-------=-------::-:--==----
"Input Connection" (Gf'page 7)
Connect the extemal device to the input
terminal.
The POA-3012CI incorporates six sets of 2-channel amplifier from
ZONE1 to ZONE6.
The same audio signal can be output from all ZONE or separate
signals
can be output from each ZONE. The POA-3012CI also supports
BRIDGED output.
Before making the connections, determine the input signals
and
output signals for each ZONE and then set up the POA-3012CI in
accordance with the following procedure.
oInput Setting
oOutput Setting
(Select the speaker output method. )
INORMAL output or BRIDGED
..". output
Connections
Connections for all compatible audio signal formats are described
in this owner's manual. Please select the types of connections
suited for
the equipment you are connecting.
With some types of connections. certain settings must be made
on the POA-3012CI. For details, refer to the instructions for the
respective connection items below.
• ~[.ii.
• Do not plug in the power cord until all connections have been
completed.
•When making connections, also refer to the operating instructions of
the other components.
•
In the case of Bus input/output connections, be sure to connect the
left and right channels properly (left with left, right with right).
•
Do not bundle power cords together with connection cables. Doing
so can result in humming or noise.
c ...... Co_n_n_e_ct~t_h_e_s_p_e_a_ke_r_c_a_b_le_._~-::---)
I"Speaker Connections"
..". (Gf' page 5)
c ...... s_e_t_th_e_o_u_tP_u_t-::c-:-h=-a::-:n-=n-=e-:-:I.-:-::=-::--~)
"OPERATION MODE"
(Gf'page
13)
4

ENGLISH
CH1&2 CH3&4 CH5&6 CH7&8 CH9&1O CHll&12
DDDDDD
• In BRIDGED mode, one channel is output from one ZONE.
• To set BRIDGED mode, select "BRIDGED" as the "OPERATION MODE" on the "Main Setup" menu.
•When BRIDGED out putting asignal input to theAUDIO INPUT terminal, input to
an even-numbered input
terminal.
•
To select asignal for BRIDGED output from among the signals ("t.:' "R:' "L+R") input to the BUS INPUT
terminal, use "INPUT SELECT"
on the "Main Setup" menu.
I Co"n~ionMethoct for ~8ID~ED O~ut.
= =
DO
CH 11 CH 12
==
DO
CH 8 CH 7
CH 9 CH 10
nc
= =
=
on
= =
CH 3 CH 4
=
o0
CH 6 CH 5
CH 1 CH 2
o0
= =
Cqnnection; Method When OutPlIttin9 2'Chan"fitl$ Ftom
ZONE,
Speaker Connections
I
5

ENGLISH
I
If speakers with an impedance lower than specified (for example 4
O/ohms speakers/NORMAL MODE) are used for an extended period
of
time with the volume turned up high, the temperature may rise,
activating the protection circuit.
There are 2kind
of protection circuits in POA·3012CI.
1. Protection circuit for individual Ampilfier (Zone1 - 6)
This protection circuit detects over load condition of the amplifier
circuit.
When the protection circuit
is activiated, the speaker output of
individual Amplifier (Zone1 -
6) is shutoff, and the Zone operation
mode indicator for protected Zone
No. flashes red.
If this happen, unplug the power cord, then check the speaker
cable and input cable connections.
2. Temperature rise protection circuit in the chassis
This protection circuit detects temperature rising in the chassis.
When the protection circuit is activiated, the power source for all
Amplifier circuits is shut off, and the power indicator flashes red.
If this happen. it may be extremely hot
in the chassis. unplug the
power cord.
Wait for it too cool off and improve ventilation around it.
Once this
is done, plug the power cord back in and turn the set's
power back on.
If the protection circuit is activated again even though there are no
problems
in the ventilation around the set nor in the connections.
the set may
be damaged. Turn the power off. then contact aDENON
service center.
Connecting the Speaker Cables
1
Peel offabout0.03 ftilO mm of sheathing
from the tip of the speaker cable, then
either twist the core wire tightly or
terminate it.
Carefully check the channel numbers and + (red) and - (black) polarities
on the speakers being connected to the POA·3012CI, and be sure to
interconnect the channels and polarities correctly.
~.Wh.~J'l u:~ing ~ b~I)~~{t .p'u:g ,t(qfNorttt,~m~~fI)~~lt,~i
Tighten the speaker terminal firmly before
inserting the banana plug.
2Thm
the speaker terminal
counterclockwise to loosen it.
4Thm
the speaker tenninal clockwise to
tighten it.
3
Insert the speaker cable's core wire to
the hilt into the speaker terminal.
-MIn-
•Use speakers with an impedance of 4to 16 O/ohms. Use a 8 to 16
O/ohms speaker for BRIDGED output.
•Connect the speaker cables
in such away that they do not stick out
of the speaker terminals. The protection circuit may be activated if
the core wires touch the rear panel or if the +and -sides touch each
other (13f" "Protection circuit").
•Never touch the speaker terminals while the power supply is
connected. Doing
so could result in electric shock.
6

ENGLISH
I
Input Connections
IBUS INPUT ConneCtions "
• To play signals input to the BUS INPUT terminal, select the channel
using "INPUT SELECT"
on the "Main Setup" menu.
•When "BUS L+R"
is used, signals input to BUS INPUT Land Rare
mixed
and output as monaural.
Audio Source
AUDIO
0t1T
A l
00
Signals input from the BUS INPUT are output from the BUS OUTPUT
terminal. These signals can be output to the BUS INPUT terminal of
another
POA-3012CI unit.
7
I AUDIOINPUT:ConnectioQ~.
oWhen Using in NORMAL MODE
To play signals input to the AUDIO INPUT terminal, use "INPUT
SELECT" on the "Main Setup" menu to set each channel to AUX.
[Example)
Connect the left and right channels from audio source to audio
inputs of arbitrary numbers.
Audio Source
AUDIO
0t1T
l A
00
oWhen Using in BRIDGED MODE
Input BRIDGED output signals to an even-numbered input
terminal.
[Example)
Connect the left and right channels from audio source to audio
inputs of arbitrary numbers.
Audio Source
AUDIO
0t1T
l A
00

ENGLISH
Modem I
For connections to the Internet, contact an ISP (Internet Service
Provider) or acomputer shop.
oOthers
•If you have an Internet provider contract for aline on which network
settings are made manually. make the settings at
"Network Setup"
(@"page 15) .
•With the
POA-3012CI. it is possible to use the DHCP and Auto IP
functions to make the network settings automatically.
•When using abroadband router
(DHCP function). the POA-3012CI
sets the
IP address. etc,. automatically.
When using the
POA-3012CI connected to anetwork with no DHCP
function. make the settings for the
IP address. etc,. at "Network
Setup"
(@"page 15l.
•The
POA-3012CI is not compatible with PPPoE. APPPoE-eompatible
router
is required if you have acontract for aline of the type with
which the
PPPoE is set.
-N'U-
• A contract with an ISP is required to connect to the Internet.
No additional contract
is needed if you already have abroadband
connection
to the Internet.
•The types of routers that
can be used depend on the ISF' Contact an
ISP or acomputer shop for details.
oBroadband Internet Connection
Abroadband line connection to the Internet is required in order to
use the POA-3012Cl's firmware update.
o Modem
This is adevice that is connected to the broadband line to
communicate with the Internet. Some are integrated with the
router
Required System
oRouter
•When using the POA-3012CI. we recommend you use arouter
equipped with the following functions:
.Built-in
DHCP (Dynamic Host Configuration Protocol) server
This function automatically assigns
IP addresses on the LAN.
.Built-in
100 BASE-TX switch
When connecting multiple devices. we recommend aswitching
hub with aspeed of 100 Mbps or greater
oEthemet Cable (CAT-5 or greater recommended)
•The POA-3012CI does not come with an Ethernet cable.
•Some flat type Ethernet cables
are easily affected by noise.
We recommend using anormal type cable.
•If the sound
is broken in an environment in which there is much
power supply noise from electric products or
in anoisy network
environment. use ashielded type Ethernet cable
(For North
America modell.
•
For the Ethernet cable. used ashielded twisted pair (STP) cable.
Do not use an unshielded twisted pair (UTP) cable. as it may exceed
noise standard limits
(For Europe modell.
oComputer
Acomputer with the following specifications is required to use a
server:
·OS
Windows® XP Service Pack2. Windows Vista
•Internet browser
Microsoft Internet Explorer
5.01 or later
•
LAN port
gID
........--~~~
LAN port!
Ethernet
connector
~
~, ...
-~
(';:::::::~~--
Internet
Connections to Other Devices '
(]I
To WAN side
-II
mJ
D~
To LAN port
C
To LAN port
(]I
D
Router
8

ENGLISH
···········ON
····STANDBY
The "POWER CONFIGURATION" setting
is valid
at the
time of a"MASTER TRIGGER ':
Voltage input to the MASTER TRIGGER input
terminal and operating status of the POA-3012CI:
t---tt=~~U
At DC 3 - 30 V········· ON
At DC 0V·· STANDBY
Mastertl'iggerinput jack
The ZONE TRIGGER ON MODE setting is valid at
the time of a"TRIGGER IN':
Voltage input
to the TRIGGER IN input terminal
and operating status of the power amplifier of
each ZONE:
At
DC 3 - 30V
At DC OV .
*If you wish to control the POA-3012CI from
an external controller using the RS-232C
connector, perform the operation below
beforehand.
G) Turn the POA-3012Cl's power.
® Turn off the POA-3012CI's power from the I--ii'+-~:'i-i
external controller.
QJ Check that the POA-3012CI is in the standby
mode.
RS.2~2C C()11"ector
This connector is used for an external controller.
The power of
an external device equipped with
atrigger input jack
can be turned on and off in
association with operations on the POA-3012CI.
•Output level: 250 mA/12 V
Check the trigger input conditions of the
connected device.
•If the trigger input level of the connected device
is higher than 250 mA/12 Vand depending on
the short-circuiting conditions. the POA-3012Cl's
protection circuit
may be activated, in which
case "TRIGGER
OUT OVER LOAD" appears on
the display. If this happens, turn off the POA·
3012CI's power and disconnect the connected
device.
I Extemal Controller
I
9

ENGLISH
Connecting the Power Cord Using the menu
o To select the item to be set
Turn the SELECT/ENTER knob until the item you want to set
appears.
o To enable lower level menu items to be displayed
Press the SELECT/ENTER knob or the \l button.
o To return to higher level menu items
Press the ~IRETURN button.
o To confirm selected item
Press the SELECT/ENTER knob.
o To exit SETUP mode
Press the SETUP button until the display returns to normal.
If
you want to configure the settings for aspecific ZONE, press
the
ZONE 1-6button for the ZONE concerned and configure the
settings.
•
In this case, the setting item of another ZONE is not displayed.
•
To configure the settings for "DIMMER MODE" and "POWER
CONFIGURATION:' use the
SETUP button to select "Main Setup"
mode.
ili" .. ca··"
-
ZONE1-6
~JRETURN
SETUP \1
c[ l
~-I----"'~~
SELECT/ENTER
Setup
In lists of selectable items or adjustable ranges, the item
surrounded
by aborder is the default value.
Example of Display of Default
Values
North America model:
To household power
outlet
(AC 120 V. 60 Hz)
:
l:J
.... _-_ .... : G)
Europe model:
To household power
outlet
(AC 230 V. 50 Hz)
Wait until all connections have been completed before connecting the
power cord.
Once Connections are Completed
@"
'0=0
12
_.
~
--
-----.
@}o~)
I ..
'@)o~
ITurning the Power On (rFpage 17)
.~[.u.
Insert the AC plugs securely. Incomplete connections could cause
noise.
[Selectable items] I~PQJJt I ,;!iID" iP!!t.0~<
Operations
For all settings, refer to "Menu map" (Gf'page 11, 12).
For details of individual settings refer to the explanations of settings
(Gf'page 13 - 16).
1Press the
SETUP button.
The POA-3012CI enters the "SETUP" mode and the first level
menu is displayed.
The selected item blinks.
2Select the required item on the menu and set it.
10

ENGLISH
r-- __ ~ ------------~-------------~-, p---------------- ,
~ _~L_;"';_'_'_~ __ .:::~98~M99~":;.:_~,_,,, ;.'-~:;...Jj:~ ~ ~_' .. _' .. ;"":.. _ .. _ '-M!q§~'_Mql?~ .. ;;; __ ~ .. __ .... =_;., __ ~
-900dB
---.-dB
BTL -900dB
BTL---.-dB
_______________ (J:L;!..~.I.~_ .. _ .. _ .. J---__.__- BTL AUX2
_______________ qL'1 __ ~.IL.____________ BTL BUS L
_____________ c;:J:i._§._~.IL____________ BTL BUS R
BTL BUS L+R
CH
12 BTL
................ Q:P .. ~.I.~ _ J--__._- BTL O.OdB
........ _. qL'1 .. ~.IL _ _
__ . ._ ... qU!._~.I.~ __ ._ .. ._. _
..................... Q:LJ J--__._- O.OdB
..................... ~!j .. f .
..................... ~!j .. ;'! .
_._. . ~!j . .J. ._ .. _. t__-__._- AUX. 1
_____________________ CJ:Lf ._. .______ BUS L
____________ ~!j __ L_________________ BUS R
BUS L+R
CH12
f)INPUT SELECT
(r::rpage 13)
%11---.-------1 .VOLUME CONTROL
(r::rpage 13)
(r::rpage 13)
Menu Map
•
11 LOW CUT FILTER
(r::rpage 13)
CH 12
_________ . .. __ ._.~!j __ L._._. l_-__.__- LCF OFF
..................... ~!j .. L _. LCF ON
.......... __ Q:t.;'! _
CH 12 BTL
- ---------- (J:iJ-~.I.~--------.----.J---,L- BTL LCF OFF
.... _ _.(J:i . .'1 .. ~.IL _BTL LCF ON
... _ .. _ .. _ (J:i .. §_~.I1o_ .
BOPERATION MODE
(r::rpage 13)
CH 12
................. ~J:L.] .. ~ .. f .... __ ._._ t__-__.__- NOR MAL
................. ~.tL;l.~ .. L. BRIDGED
............ _ ~t! .. 9..!!! .. § _ .
................. ~.t!.J..!!! .. !'! _ .
_. __ .~.t!_!!._!!!_J.Q .
CH 11 & 12
CH 12 BTL
- _._ ..... _._.~.tU..§!.L .. _ __ ~--.-- L- BRIDGED
.......... _ ..... ~.ti.;lAL .. _ _ NORMAL
............... _~.t!.~.~ .. § ._._ _
. ~.t! . .?.!!! .. !'! _ _
.._ .. _ _ .. _.Q:UL~.J.Q _ ..
CH 11 & 12
IIZ0NETRIGGER ON
MODE
(r::rpage 14)
_ .. ~_t:l_.J_.!!! __ f ._. J---__.__- CONSTANT
..... . __ ~.t:I .. ;lA'1._. __ ._____ TRIG. IN
....... __ ~.t! . .9..!!! .. §A.SIGNAL
. __ . _ .. _ .. ~_t!..7..~_.~L __ . __ OFF
_. __ ._ .. _ .. _. ~_t:l_!!..~.J.Q __ .
CH 11 & 12
l'
INetwork Setup
,Option Setup
II DIMMER MODE
(r::rpage 14)
DpOWER
CONFIGURATION
Bright
Dim
Dark
OFF
POWER
BUnON
ON LINE
MASTER TRIGGER
11

OFF [Address
ON ---
Name
DNetwork.
Information
(Gr'page 15)
fI Network Setup
(Gr'page 15)
DMaintenance
(Gr'page 16)
fIFirmware Update
(Gr'page 16)
DHCP
IP Address
Mac Address
DHCP
Proxy
ON
OFF
IPAddress
~
Subnet Mask
Default Gateway
Primary
DNS
Secondary DNS
-----1- Proxy Address
L Port
-----1- Proxy Name
L Port
ENGLISH
•
12

ENGLISH
NORMAL MODE
BRIDGED MODE
CH 1 &2
0 0
CH 3&4
00
CH 5&6
0 0
CH 7 &8
0 0
CH 9& 10 0 0
CH 11 & 12
0 0
Default: NORMAL MODE
[Selectable Channels]
Sets each of the following channel pairs.
[Selectable items]
.()p.l;~n()NI\IIODE . . .. ~
Set$lDeo0tpufrnElthod for channe~ineach lONE. ....
•During NORMAL MODE, ZONE operations mode indicators are lit
green.
•During BRIDGED MODE, ZONE operations mode indicators are lit
orange.
-N·n.
The method of connecting speakers differs for each mode. Connect
the speakers in accordance with the mode setting. For details, refer to
"Speaker Connection"
((jf'page 5).
I"~J :2-channel output
l,!g~iP;; :BRIDGED-channel output (1-channel output)
,.
:AUDIO INPUT terminal of each ZONE.
:L terminal of BUS INPUT
:R terminal of BUS INPUT
: Land Rterminals of BUS INPUT .
Inputs a Land Rmixed mono signal.
[Selectable items]
[Selectable Channels]
For details of the channels which can be set in each mode, see
[Selectable ChannelsI in "BVOLUME CONTROL:'.
.AUX
"
.8,1tS;!,..
BUSR
,BUU+Il
~~.';:;:o-:..t:~'~'''.-
[Selectable Channels]
For details of the channels which can be set in each mode, see
[Selectable Channelsl
in "BVOLUME CONTROL:'.
[Selectable items]
~~~::; :Low frequency component is cut.
l:ji>QFf,~tl :Low frequency component is not cut.
fJ INPUT SELECT
II LOW CUT FILTER
II ZONETRIGGER ON MODE
II POWER CONFIGURATION
DOPERATION MODE
II DIMMER MODE
BVOLUME CONTROL
[Selectable Channels]
Channels which can be set in each mode.
NORMAL MODE BRIDGED MODE
CH 10x
CH 200
CH 30x
CH 400
CH 50x
CH 60 0
CH 70x
CH 800
CH 90x
CH 10
0 0
CH 11
0X
CH 12
0 0
•
1
0: Setting possible
x : Setting not possible
Default: NORMAL MODE
13

ENGLISH
[Selectable Channels]
For details of the channels which can be set in each mode. see
[Selectable Channelsl
in "0 OPERATION MODE" (!:'?page 13)
[Selectable items]
1·~g,.§iqJ'J :The power amplifier operates constantly.
tli~[li;i;!I!;J;' :The power amplifier operates when trigger input is
detected.
When trigger input is not detected, it remains
in
standby mode.
;~"':;,!!l!iLi, : Very low display brightness.
~ .. ::.J!~fusi., :Display is off unless controls are operated.
II
When setting to "Dim': "Dark" and "OFF': the display brightness
changes to "Bright" for about 3seconds during the operation before
reverting to the set brightness. •
:Operate with the ON/STANDBY button only.
~~~~~=
rji!;~ii!!kq!I;~lIgii.~'i :Operate from an external device via Ethernet
or RS-232C input.
li;.autllllfi~~::1 :Operate by detection of atrigger signal input
to the
MASTER TRIGGER input terminal.
•
Turns on when asignal is detected.
•If no input
is received for aperiod of 10
minutes, it switches to standby mode.
The POA-3012CI accepts +3 - 30V trigger input.
ik;~1§!g~:i;,The power amplifier operates when an audio signal is
input.
If no input
is received for aperiod of 10 minutes. it
switches to standby mode.
:'J;J;ii;~!~~:d:JJJl : Turns the power amplifier off.
.,
• The POA-3012CI accepts +3 - 30 Vtrigger input.
•
Even when "ON LINE" or"MASTERTRIGGER" has been set. power
source operation
is possible by means of ON/STANDBY button.
14

~ button:
\l button:
ZONE 6button :
ZONE 5button :
®Use the following buttons to input the address and press the
SELECT/ENTER knob.
*Button functions when entering address
SELECTJENTER knob: Turn Select
Press
·· Confirm
Cursor to right
Cursor
to left
Setting during address entry
Cancel entry
df~:
Set the IP address within the ranges shown below. The Network
function cannot
be used if other IP addresses are set.
CLASS A: 10.0.0.0 -10.255.255.255
CLASS B: 172.16.0.0 -172.31.255.255
CLASS C: 192.168.0.0 -192.168.255.255
i~.~~:
When connecting an xDSL modem or terminal adapter directly
to the POA·3012CI, input the subnet mask indicated in the
documentation supplied by. your provider. Normally input
255.255.255.0.
!,~.~~~,;.
When connected to agateway (router), input its IP address.
t~~PN$,.~~DNS
If there is only one DNS address indicated in the documentation
supplied by your provider, input it at "Primary DNS".
If there are
two or more DNS addresses, input the first one at "Secondary
DNS".
®Press the SELECT/ENTER knob.
Setup is complete.
*When connecting to the network via aProxy server, select
"Proxy" and press the
SELECT/ENTER knob (Gr"page 16 "Proxy
settings").
..... 4f
..
'-.L;,-
L·' !"",!,=. Sec 0 no::! .::t~-."/
r ~ Select ·DHCPW• ,I : ;1{:'~lt
______ '--_ -_ ~_.-:.:-:- ·:~~ .. ::I'=@=2 =Se=t=·Q=F=F
M
=. '1-
IP Addre~~ 1
[Ti;~:r.;~:~:::~~:::}:}. d .. •••• .. ••••• .. :
I
.. _~J~ S'!·!.f;. !_1'L~~t:_ --- - -. I :
,I .-::. C' t:' .-::,0=1:" .') t::' 0= .:"~:-.& ••••• ' •• It lit '" .' i1*'
'. '~'.l_'_~'.l_''''''''''-''''''' '-'_~. •
·
..
•
........,
"------;:================-~ .
•
P t;'_!-'j§.!-~':~ _ I~i2 .. :
~£1. ... ~J [1 fL~ •••• 4)._
'-;::====::=:=:===========~ :
·
·
Use this procedure to configure the Wired LAN settings.
Wired LAN settings
I®Input the add res;.
CD Select" DHCP" and press the SELECTJENTER knob.
@ Turn the SELECT/ENTER knob to set "DHCP" to "OFF", then
press the
SELECTJENTERknob.
The DHCP function is disabled.
1Connect the LAN cable (t::V' page 8).
2
Tum on the POA-3012CI (t::V'page 17).
POA-3012CI performs automatic network setupdue to the DHCP
function ..
When connecting to anetwork that has no DHCP function,
perform the setting
in step 3.
3Set the IP address at the menu "Network Setup" -
"Network Setup".
I'
·~fittwork '§~p .. , .•.
i Mak~settingsfor'~!f~:LAN.
Network Setup
oNetworklnfonnation
Network Setup
It:,
.. to::
• Menu tree •
•If you are using abroadband router (DHCP function). there is no need
to make the settings at "Setting the
IP Address" and "Setting the
Proxy", since the
DHCP function is set to "ON" in the POA-3012CI's
default settings.
•If the
POA-3012CI is being used connected to anetwork without the
DHCP function, the network settings must be made. In this case,
some knowledge of networks
is required. For details, consult a
network administrator.
•If
you cannot connect to the Internet, recheck the connections and
settings (Gr"page 8)
•If you do not understand about Internet connection, contact your ISP
(Internet Service Provider) or the store from which you purchased
your computer.
aNetwork,Infonnation
DisplaY ~etwork .Information.' ,,'
Network Setup
Make network settings.
Main Setup
•DHCP (Dynamic Host Configuration Protocol) :
These are systems by which the IP address and other network
settings are automatically set for the
POA-3012CI, computer,
broadband router
and network devices.
•DNS (Domain Name System) :
This is asystem for converting the domain names used when
browsing Internet sites (for example,
.. www.denon.jp .. )into the
IP addresses actually used for communications (for example,
"202.221.192.106").
[Items to be checked] h.PttCP. ON or Off .. . ., Address
:'~<<>:i, ,'''''''''''~;:'': -!h:,;;-_"~':~':'U':;,};_ Wj(L~~;~
,tfA~6!!!tel
ENGLISH
•
15

ENGLISH
•
)j:
kt
<, ':'Q~lrti9"
;t
Updating failed Updating failed.
Login failed Failure to log into server.
Server is busy Server is busy. Wait awhile then try again.
Connection fail Failure connecting to server.
II fjl1Jlware Update
UPdate the'firmware of themulti channel power amplifier.
Update Check
You can check for firmware updates. You can also check approximately
how long it will take to complete
an update.
Execute the update process.
When updating starts, the power indicator lights red. "Updating
** *" is shown on the display during updating. Once updating is
completed, "Updatingcomplete" is displayed.
"Latest firmware"
is displayed when the firmware is the latest
version.
'*' If the display reads as shown below, check the settings and network
environment, then update again.
Update Start
.~(.ji.
•Connection to the network and specific settings are required to
update the firmware.
For details, see page 8, 15.
• Do not turn off the power until updating is completed.
•Normally there
is no need to use this function, aside from the cases
described below.
,
The Firmware Update function is only used for updating the
firmware (free or for acharge)
via the Internet, for example for the
purpose of adding functions to the
POA·3012CI in the future.
·Information regarding the Firmware Update function will
be
announced on the DENON web site each time related plans are
defined.
· A broadband connection to the Internet is required
to use this
function
(rF' page 8).
· Even with abroadband connection to the Internet, approximately
13 min is required for the updating procedure to be completed.
Once updating starts, normal operations on the
POA-3012CI cannot
be performed until updating is completed.
Furthermore, updating the firmware may reset the backup data for
the parameters, etc., set for the
POA-3012CI.
~ button:
\l button:
ZONE 6button:
ZONE 5button:
DISPLAY button:
@ Use the following buttons to input the proxy server address or
domain name
and press the SELfCT/ENTER knob.
'* Button functions when entering address
SELfCT/ENTER knob: Turn .. ··Select
Press · · .. ··Confirm
Cursor to right
Cursor to left
Setting during address entry
Cancel entry
Character insert/delete/overwrite
Cursor
~: Character insert
Cursor
~: delete
Cursor.: overwrite
When "Address" is selected in step ®: Input the address
When "Name" is selected in step ®: Input the domain name
® Turn the SELfCT/ENTER knob to select the "Port" and press
SELfCT/ENTER knob.
® Use the above buttons to input the proxy server port number and
press the SELfCT/ENTER knob.
(J) Press the SELfCT/ENTER knob.
Setup
is complete.
.M,intenan~L '.
Thj!) ;,5ets:' the function for maint~nance by' a DENQN
'. s~ivic~~rson'or instalter~ (For professJorjal use only.) , .
This function allows a DENON serviceperson or installer to check the
POA-3012CI's status and make settings via the Internet.
'N'O*
Only use this function if so instructed by aDENON serviceperson or
installer.
.c:: * F' ,-. ,-, ',., .....
~r------------.
~ _.Iid,~ ~-.;..;:;;:.=: _ ~
I- •
=--=~~"="='-a--------'
®Selecting the
input method
Example) Address
@Input the
address
or domain
name.
oProxy settings
Make this setting when connecting to the Internet via aproxy server.
:+: t·~ e 1:: i .• J0 ~-. k Set U F-
CD Select MProxy·. I •• ""-...:~",:",j:,-=:,-=,;-",~-"":-,,,::-,,,:-,,-:-,-} -----'
[Characters that can be input]
a ~~ O~9;
"';::}:i,:f..,>;:,>!,<
.0< ... : .·~;::,':'!.·Jl· tt':JJ.i.:'fi:1 ~ nJl~.a.s.e).
®Input the port
number.
CD Select menu "Network Setup" -"Network Setup" -"Proxy" and
press the SELfCT/ENTER knob.
<1> Turn the SELfCT/ENTER knob to set "Proxy" to "ON" and press
the
SELfCT/ENTER knob.
The proxy server is enabled.
® Turn the SELfCT/ENTER knob to select the proxy server input
method.
and then press the \l button.
[Selectable items]
AddrllSS :Select when inputting by address.
Name :Select when inputting by domain name.
<>:,:".J,;=~~"""
16

ENGLISH
Click the menu
CHANNEL SETUP IGrExample: 1)
SYSTEM SETUP IGrExample : 2)
WARNING AND PROTECTION DATA
IGrExample :3)
AUDIO SIGNAL AND TRIGGER
INPUT IGrExample : 4)
OPTION SETUP IGrExample: 5)
-Network SetupW - -Network Infonnation- (Grpage 15)
.OPClr:atin9 . th~. POA~3012CI . Using a
BroW$M (Web'f;Ontroll
. -,-:- ,' •. ' ,; -.,-, .'.' . . .. ~.,. '-~,-_:",</,_. - , .. :
This.function lets YolJ~ratethe Pq..\-3P12CI using Internet
Exp.lorer!>Y",. ." g ...... ;.y;·Y.c
Y
;,.:..,' , ... 'y;":'.' <.•. .' .. .
Click -SAVE- when you want to save settings,
and click -LOAD- when you want to call settings
Becomes each operation screen
1Check the POA-3012CI's IP Address.
2Input the POA-3012CI's
IP Address in Internet
Explorer.
For example. if the IP address is "10.3.18.90; enter
http://10.3.18.90.
3Hthe top menu is displayed, click ''Setup Menu"•
4When the ''Setup Menu" is displayed, click on the
menu you want to operate.
--------
1Press the DISPLAY button.
*Zone status is indicated on the bottom line of the display.
* Turn the SELECTjENTER knob to change the display as follows.
[
Channel No. & INPUT Line -- VOLUME CONTROL lellel I
- .. ZONET.ON MODE -- LON CUT FILTER -----J
Check the Status of Each Channel
Other Operations
2Press the DISPLAY button again.
*System status is indicated on the bottom line of the display.
* Turn the SElfCT/ENTER knob to change the display as follows.
POWER CONFIG -- DIMMER
o To Retum to the Regular Display
Press the .6./RETURN button until the display returns to normal.
o To Adjust the Volume
Refer to "VOLUME CONTROL.:' on the "Main Setup" menu
(Grpage 13)
o To Switch Input Setting
Refer to "INPUT SELECT" on the "Main Setup" menu (Grpage
13).
o To Reduce the Low Frequency Volume
Refer to "LOW CUT FILTER" on the "Main Setup" menu (Grpage
13).
i rO:' .-:
i I~·:L
Press the ON/STANDBY button.
The power indicator flashes green and the power turns on.
*The signal input to each channel is output from the speaker
terminal of each channel.
* The setting status of each channel is indicated on the display.
* Turn the SELECT/ENTER knob to change the channel displayed.
Output channel Input terminal
I I
OPERATION MODE Volume level
(No display when in "NORMAL MODE")
o~I~-DT""B-y----z-J-E-5 -D-I-J: )1
.6./RETURN
Turning the Power On
Operation
ZONE op,,,tioo mod, iOdi"'tO'~'~~SELECTIENTER
... -,;~~
.. -_:..!J
o To return to STANDBY
Press the ON/STANDBY button again.
The power indicator lights red.
-k
ll
".
-When the "POWER CONFIGURATION" is set to "MASTER
TRIGGER': the device will automatically enter the standby status
when no trigger input is detected for aperiod of
10 minutes.
-When the "POWER CONFIGURATION"
is set to "ON LINE': send
astandby command to the ETHERNET terminal or the
RS-232C
terminal of the POA-3012CI.
-Power continues to be supplied to some of the circuitry even when
the power
is in the standby mode. When leaving home for long
periods
of time or when traveling, unplug the power cord from the
power outlet.
I
17