Denver AC-5000W MK2 User manual

AC-5000W MK2 Quick Start Guide
ENG 1
Camera Diagram:
LCD Display Diagram:
Turn on the Wi-Fi camera, the LCD will display the following status and settings:
1. Camera mode
2. Video recording mode (default)
3. Wi-Fi icon (display when enabled)
4. Micro SD card icon (display when loaded)
5. Resolution icon:
In camera mode, HI stands for 8 Mega Pixels (interpolated) (3264x2448), and in video
recording mode, it stands for FHD (1920x1080, 30fps);
In camera mode, LO stands for 5 Mega Pixels (2592x1920), and in video recording mode,
it stands for 720P (1280x720, 30fps);
HILO only displays in video recording mode, standing for 720P (1280x720,60fps).
6. Mute mode, displays when enabled, and disabled by default.
7. Counter, displays up to 999.
8. Timer, displays hours and minutes.
9. Battery icon: current battery level of the camera.
Note: The above icons may vary according to the status of the camera.
Using your camera:
1)When you use the camera for the first time, please:
Insert a micro SD or micro SDHC card (not included), as shown in the following picture.
A Class 10 Micro SD Card is required for this camera.
Turn off the camera before inserting or removing the card.
2)Turn on/off
1, Turn on: press and hold the button for about 3 seconds, LCD displays “ON” and a
beep can be heard from buzzer.
2,Turn off: press and hold the button for about 3 seconds, LCD displays “OFF” and a
beep can be heard from buzzer.
3)Start to Use
1. Default setting: After turn on the DV, the default setting is as below:
Video recording
mode icon The DV is in video recording mode.
HI Video resolution FHD: 1080p@30fps
Recording time Stands for 0 hour and 00 minute.
Micro SD card
icon Display when a Micro SD card is inserted, otherwise no display.
Battery level Battery is full
Mute icon The DV is in Mute mode, no Beep will be heard
when pressing the buttons. It displays only
when Mute mode is activated.
Wi-Fi icon Display when activated.
2.Shooting modes. The DV provides different shooting modes. Press the button
repeatedly, the following first two modes will show on the DV screen , and other models
display on the APP operation.
Video HI stands for FHD (1920x1080,30 fps) video
Lo stands for 720P (1280x720,30 fps) video
HILO stands for 720P (1280x720,60 fps) video
Photo HI stands for 8M (3264 x 2448) resolution
Lo stands for 5M (2592 x 1920) resolution
Continuou
s shot The DV supports taking 3 photos continuously (only via App)
Self-timer In self-timer mode , you can set 0s, 2s or 10s (only
via App)
3, Video
( With maximum 29 minutes video recording and then stop.Must be started manually on
the camera again.)
To record a video, please check whether the DV is under Video mode. If the icon is
not displayed on the screen, press the button repeatedly until it appears.
Start recording: Press and release the button, the icon and [:] displayed in
LCD will flash. At the same time the red indicator will flash too, meaning the recording is
in process.
Stop recording: Press and release the button, the icon and [:] displayed in
LCD will stop flashing. At the same time the red indicator will stop flashing either, meaning
the recording is stopped.
When the Micro SD card is full, or the battery runs out, the recording will stop
automatically, and the recorded video will be saved before the DV turns off. Stops
automatically when 29 minutes of video recording is reached.
4. Photo
To take a photo, please check whether the DV is under Camera mode. If the icon is
not displayed on the screen, press the button repeatedly until it appears.
Press and release the button, a beep will be heard and the red indicator will flash,
meaning a photo is taken.(If you take photos more than 999 copies, the LCD screen
display only 999)
5. Enable/disable Wi-Fi
The Wi-Fi is disabled by default. Press the Wi-Fi button on the side of the DV to enable it.
When starting connecting to Wi-Fi network, the indicator will flash, and when a Wi-Fi
network is connected, the indicator will remain on, and the Wi-Fi icon will display on LCD
screen.( In order to save power, Wi-Fi will be automatically disabled if no terminal is
connected after 30 seconds)
1. Shutter button 8. Micro SD card slot
2. Microphone 9. Micro USB port
3. LCD display 10. Battery cover push switch
4. Lens 11. Charge/Busy light
5. Wi-Fi switch and status indicator (red) 12. HDMI Port
6. Power /Mode button
7. Infrared signal reception light
Wi-Fi er disabled by
default
When Wi-Fi is enabled, the
Wi-
Fi icon will display on LCD

AC-5000W MK2 Quick Start Guide
ENG 2
4) Using the Battery
1. Install the battery.
Please install the lithium battery correctly as shown:
Figure 1 Figure 2 Figure 3 Figure 4
Step 1. Push the battery cover switch to the unlock position( ), and remove the
battery cover.As shown in figure 1.
Step 2. Place the lithium battery into the battery slot. Make sure the polarity of the battery
is corresponding to the symbols of the camera shell( ). As shown in figure 2 and
figure 3.
Step 3. Install the battery cover back in place, and lock the switch to
the lock position( )to fix the battery. As shown in figure 4.
2. Charging the battery:
The camera uses removable rechargeable lithium battery. When the camera is off,
connect it to the PC via the USB cable to charge the battery.
During charging, the status indicator (blue) will be lit up and the indicator will
turnoff when charging completes.
Note: When the camera is on, connecting it to the PC will not charge.
5) Pair the Camera to Your Smartphone or Pad.
1. Download and install the app “DENVER ACTION CAM 1”from Apple
Appstore® or Google Play
2. Press the Wi-Fi button on the side of the camera to initialize the signal, the LED will be
red
3. Search for the wireless signal “DENVER AC-5000W MK2” on your smartphone or
tablet using
the password “1234567890”.
4. You can now start using the camera once the wireless signal is connected and you
have opened the app.
Warning
• Lithium battery inside!
• Do not try to open the product!
• Do not expose to heat, water, moisture, direct sunlight!
CAUTION!
ALL RIGHTS RESERVED, COPYRIGHT
DENVER ELECTRONICS A/S
Electric and electronic equipment and included batteries contains materials, components
and substances that can be hazardous to your health and the environment, if the waste
material (discarded electric and electronic equipment and batteries) is not handled
correctly.
Electric and electronic equipment and batteries is marked with the crossed out trash can
symbol, seen below. This symbol signifies that electric and electronic equipment and
batteries should not be disposed of with other household waste, but should be disposed
of separately.
As the end user it is important that you submit your used batteries to the approriate and
designated facility. In this manner you make sure that the batteries are recycled in
accordance with legislature and will not harm the environment.
All cities have established collection points, where electric and electronic equipment and
batteries can either be submitted free of charge at recycling stations and other collection
sites, or be collected from the households. Additional information is available at the
technical department of your city.
Hereby, Inter Sales A/S, declares that this product (AC-50002 MK2) is in compliance with
the essential requirements and other relevant provisions of Directive 1999/5/EC. A copy
of the Declaration of conformity may be obtained at:
Inter Sales A/S
Stavneagervej 22,
DK-8250 Egaa
Denmark
Imported by:
DENVER ELECTRONICS A/S
Stavneagervej 22
DK-8250 Egaa
Denmark
www.facebook.com/denverelectronics