Denver ACT-8030W User manual

ACT-8030W Quick Start Guide
ENG 1
I
In nt tr ro od du uc ct ti io on n t to o a ap pp pe ea ar ra an nc ce e a an nd d k ke ey ys s
Display/Menu key
2.0’’ HD LCD
Lens
Infrared remote
control lamp
Charging /Busy indicator
Busy indicator
Microphone

ACT-8030W Quick Start Guide
ENG 2
Wifi/Down key
HDMI port
Power/Mode key
Battery door
Micro SD Card
Shutter/OK key
Micro USB port
Speaker

ACT-8030W Quick Start Guide
ENG 3
S
St ta ar rt t u us si in ng g _ __ __ __ __ __ __ _
1. Charge the built-in lithium battery
Connect the camera to the computer for charging, at this time, the charging indicator will be in red, and it
will be off after charging. Generally, it takes 2-4 hours to charge the battery.
2. Use the storage card
1. Push the Micro SD card into the slot till it is in place as per the instruction in concavely engraved words by
USB cable

ACT-8030W Quick Start Guide
ENG 4
the storage card slot.
2. To take out the Micro SD card, press the tail of the storage card inwardly softly and it will be popped out.
Note: There’s no built-in memory unit in the camera, so make sure to insert a storage card into it prior
to use (it is recommended that a Micro SD card of better quality be used).
3. Power on/off
3.1 Power on: Press Power key for 3 seconds, the screen will be on and the camera will be started.

ACT-8030W Quick Start Guide
ENG 5
3.2. Power off: Hold on Power key for 3 seconds when the camera is in the idle state to turn it off.
3.3. Auto screen off: The screen will be turned off automatically when the time that the camera is in the
idle state for automatic screen off to save power. After that, the lamp for screen off will be on.
3.4. Power off when the camera is lack of electricity. When electrical quantity of the battery is very low, an
icon of will be displayed on the LCD screen, prompting you to charge it in time. When the icon
turns red and flickers, the camera will be turned off automatically.
4. Shift among functional modes
The camera has 3 modes, namely video recording mode, shooting mode and replay mode. After power is on,
press Power key to shift among them.
Video recording mode Shooting mode
5. Indicator
Busy indicator (red): When the camera is busy such as recording videos, shooting photos and turning off
screen automatically, the work indicator will flicker.
Charging indicator (blue): When it is on, the user is prompted that the camera is being charged and it will
be off after charging is completed.

ACT-8030W Quick Start Guide
ENG 6
6. Video recording mode
After power is on, the video camera will enter video recording mode directly and in preview mode, press
Shutter key to start video recording; Press it again to stop shooting. If the memory card is full or electrical
quantity is low, it will also stop shooting:
Taking a photo while recording: press the Power button during recording to take a photo. When a photo is
taken, the texts “CAPTURE DONE” will display on the screen.
1. Icon of mode, indicating video recording mode;
2. Indicate quality of video;
3. Indicate size of video, and FHD 1080P (60FPS)
/ FHD 1080P (30FPS) / HD 720P (120FPS)
/ HD 720P (60FPS) / HD 720P (30FPS) is optional;
4. Recording time, indicating recordable length of time;
5. Icon of battery, indicating current electrical quantity;
( With maximum 29 minutes video recording and then stop.Must be
started manually on the camera again.)
7. Shooting mode
After power is on, press Power key twice to enter shooting mode, and in preview state, press Shutter key
to take a photo:

ACT-8030W Quick Start Guide
ENG 7
1. Icon of mode, indicating the current is shooting mode;
2. Size of video, and 5M/8M//12M/16MP is optional;
3. Icon of quality of pictures;
4. Counter, indicating number of photos to be taken;
5. Icon of electrical quantity of battery.
8.Menu operation
There is a different menu in each working mode as shown in the following figures:
Menu for video recording Menu for shooting mode

ACT-8030W Quick Start Guide
ENG 8
Menu for setting mode Menu for replay mode
Operation: Press Menu key, the menu for this mode will be displayed on the LCD. At this time, press
Power key to move the cursor leftward or rightward and select on the menu, and press WIFI key to move the
cursor upward or downward and select on the menu in a circulating way. Press OK key to confirm and press
Menu key to return or exit from menu mode.
Description of “Slow Motion” function
Slow-Motion refers to record at normal FPS and play at lower down FPS. For example, to record a video at
60fps, and then play the video at 30fps, you will see a slow motion.
Operation: in the menu, select “Slow Motion” and press OK to enter the sub-menu, move the cursor to select On,
then press OK to conform. You will see the following display:

ACT-8030W Quick Start Guide
ENG 9
Slowmotion Icon
Press the Shutter to start recording, and press Shutter again to stop;Play the slow-motion video:
Press the Power button to switch to Playback mode; select Video
Press OK to play the video in a slow-motion effect, as shown in the right picture.

ACT-8030W Quick Start Guide
ENG 10
Description of “timelapse” function
Time Lapse function is mainly used to shoot cityscape, natural scenery, astronomical phenomena, and
biological evolution. This function allows the device to take a photo automatically according to the
pre-set time interval, then create a video by collecting, analyzing the processing these taken photos;
the playing speed of the video is adjustable through changing the interval of the frames (photos), thus
to finally create a special video effect.
Operation:
1 In the menu, select “Timelapse” and press OK to enter the sub-menu, then move the cursor to select time interval
among 3s/5s10s30s/1min, and then press OK to confirm.
2 In the menu, select “Timelapse Duration” and press OK to enter the sub-menu, then move the cursor to select the
duration among 5min/10min/15min/20min/30min/60min/Unlimited, and the press OK to confirm. You will see the
following display:

ACT-8030W Quick Start Guide
ENG 11
Timelapse icon
Press the Shutter to start the Timelapse recording, and press Shutter again to stop;
Play the recorded video: press the Power button to switch to Playback mode; select Video
Press OK to play the video in a timelapse effect, as shown in the right picture.

ACT-8030W Quick Start Guide
ENG 12
Note: If Timelapse funcion is activated under Photo mode, the device will only take photos according to the pre-set
time interval, and will stop when reaching the set duraion. The operation is similar to Video mode.
Application of remote controller
1. Definition of keys of remote controller
Keys of remote controller are as shown
in the right figure:
2. Use of remote controller:
Using the remote controller, you can achieve functions of power on, video recording, shooting and power off
without operating on the camera. Just point the signal transmission port of the remote controller at IR signal
receiving lamp of the camera, and press corresponding keys to achieve functions of power on, video recording,
shooting and power off.
Power on/off key
Video recording key
Shooting key
Signal transmission port
Infrared remote control lamp

ACT-8030W Quick Start Guide
ENG 13
Connect device to HDTV:
Connect the video camera to an HDTV with a HD cable as shown in the following figure, display signals in
the camera will be output into the HDTV automatically, and you can browse HD videos and photos that are
recorded or taken in the HDTV.
Diagram of connection
Signal transmission

ACT-8030W Quick Start Guide
ENG 14
APP(forAndroid and iOS System)
I. How to Obtain the APP Installation Program
1. For the Android System, you can search “DENVER ACTION CAM 2” in the Play Store to obtain
corresponding installation programs, and then you can install them according to the indicated steps.
2. For the IOS System, you can search “DENVER ACTION CAM 2” in the APP Store to obtain
corresponding installation programs, and then you can install them according to the indicated steps.
II. Camera WIFI and SystemApplications
AndroidApplications
1. Please install the DENVER ACTION CAM 2 application program (provided by the Supplier or the Internet)
for the Android mobile phone or tablet PC, and then the Display Screen will show the Icon ;
2. Insert a Storage Card into the Camera and then power it on. Press the WIFI key to conduct WIFI connection,
and the Screen of the Camera will show the WIFI signal Icon with the external screen revealing WIFI
Connecting.

ACT-8030W Quick Start Guide
ENG 15
3. Enable the WIFI function of the Android mobile phone or tablet PC, and try to find the AP Name
ACT-8030W; please conduct connection between them till the system reveals a successful connection;
if you are conducting WIFI connection for the first time, please input the password: 1234567890.
4. Tap and enable the Application Program Icon on the Android mobile phone or tablet PC; you can
directly view the preview picture transmitted by the Camera (see the following picture), and then conduct
relevant operations.
IOS Applications
1. Please install the DENVER ACTION CAM 2 application program (provided by the Supplier or the Internet)
1. Resolution
2. White Balance
3. Settings (Enter Settings Menu)
4. Wi-Fi Signal Icon
5. Camera’s Battery Status Icon
6. Enter the Playback Mode
7. Shutter Button
8.Video Mode
9. Photo Mode
10. Timelapse Mode

ACT-8030W Quick Start Guide
ENG 16
for the IOS mobile phone or tablet PC, and then the Display Screen will show the Icon ;
2. Insert a Storage Card into the Camera and then power it on. Press the WIFI key to conduct WIFI connection,
and the Screen of the Camera will show the WIFI signal Icon with the external screen revealing WIFI
Connecting.
3. Enable the WIFI function of the IOS mobile phone or tablet PC, and try to find the AP Name ACT-8030W;
please conduct connection between them till the system reveals a successful connection;
if you are conducting WIFI connection for the first time, please input the password: 1234567890.
4. Tap and enable the Application Program Icon on the IOS mobile phone or tablet PC; you can
directly view the preview picture transmitted by the Camera (see the following picture), and then conduct
relevant operations.
1. DV battery icon
2. Video resolution
3. White balance
4. Setup (enter setup menu)
5. Enter Playback mode
6. Timelapse Mode
7. Photo mode
8. Video mode
9. Shutter button

ACT-8030W Quick Start Guide
ENG 17
Warning
•Lithium battery inside!
•Do not try to open the product!
•Do not expose to heat, water, moisture, direct sunlight!
•Only charge with the original adaptor supplied with this product!
CAUTION!

ACT-8030W Quick Start Guide
ENG 18
ALL RIGHTS RESERVED, COPYRIGHT
DENVER ELECTRONICS A/S
Electric and electronic equipment and included batteries contains materials, components and substances that
can be hazardous to your health and the environment, if the waste material (discarded electric and electronic
equipment and batteries) is not handled correctly.
Electric and electronic equipment and batteries is marked with the crossed out trash can symbol, seen below.
This symbol signifies that electric and electronic equipment and batteries should not be disposed of with other
household waste, but should be disposed of separately.

ACT-8030W Quick Start Guide
ENG 19
As the end user it is important that you submit your used batteries to the approriate and designated facility. In
this manner you make sure that the batteries are recycled in accordance with legislature and will not harm the
environment.
All cities have established collection points, where electric and electronic equipment and batteries can either
be submitted free of charge at recycling stations and other collection sites, or be collected from the households.
Additional information is available at the technical department of your city.
Hereby, Inter Sales A/S, declares that this product (ACT-8030W) is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC. A copy of the Declaration of conformity
may be obtained at:
Inter Sales A/S
Stavneagervej 22,
DK-8250 Egaa
Denmark
Imported by:
DENVER ELECTRONICS A/S
Stavneagervej 22
DK-8250 Egaa
Denmark
www.facebook.com/denverelectronics